EN 62271-200:2004

High-voltage switchgear and controlgear - Part 200: AC metal-enclosed switchgear and controlgear for rated voltages above 1 kV and up to and including 52 kV

Specifies requirements for factory-assembled metal-enclosed switchgear and controlgear for alternating current of rated voltages above 1 kV and up to and including 52 kV for indoor and outdoor installation, and for service frequencies up to and including 60 Hz. Enclosures may include fixed and removable components and may be filled with fluid (liquid or gas) to provide insulation. This standard defines several types of metal enclosed switchgear and controlgear which differ due to - the consequences on network service continuity in case of maintenance on the switchgear and controlgear; - the need and convenience of maintenance of the equipment. For metal-enclosed switchgear and controlgear containing gas-filled compartments, the design pressure is limited to a maximum of 300 kPa (relative pressure). Metal-enclosed switchgear and controlgear for special use, for example, in flammable atmospheres, in mines or on board ships, may be subject to additional requirements. Components contained in metal-enclosed switchgear and controlgear are to be designed and tested in accordance with their various relevant standards. This standard supplements the standards for the individual components regarding their installation in switchgear and controlgear assemblies. This standard does not preclude that other equipment may be included in the same enclosure. In such a case, any possible influence of that equipment on the switchgear and controlgear is to be taken into account. This first edition of EN 62271-200 cancels and replaces the third edition of EN 60298, published in 1990, and constitutes a technical revision. Significant technical changes from the third edition of EN 60298 are as follows: This revised document has been basically changed to be updated to today's use of high- voltage switchgear and controlgear up to 52 kV. The main changes are: new definitions and classification of equipment, introduction of internal arc classes (IAC) and its testing. This standard is to be rea

Hochspannungs-Schaltgeräte und -Schaltanlagen - Teil 200: Metallgekapselte Wechselstrom-Schaltanlagen für Bemessungsspannungen über 1 kV bis einschließlich 52 kV

Appareillage à haute tension - Partie 200: Appareillage sous enveloppe métallique pour courant alternatif de tensions assignées supérieures à 1 kV et inférieures ou égales à 52 kV

Spécifie les exigences pour l'appareillage préfabriqué sous enveloppe métallique pour courant alternatif, prévu pour être installé à l'intérieur et à l'extérieur, pour des tensions assignées supérieures à 1 kV et inférieures ou égales à 52 kV et pour des fréquences de service inférieures ou égales à 60 Hz. Les enveloppes peuvent contenir des composants fixes et amovibles et peuvent être remplies de fluide (liquide ou gaz) pour assurer l'isolation. Cette norme définit plusieurs types d'appareillage sous enveloppe métallique qui diffèrent par - les conséquences sur la continuité de service en cas de maintenance sur l'appareillage; - les besoins et la facilité de maintenance des équipements. Pour l'appareillage sous enveloppe métallique comprenant des compartiments à remplissage de gaz, la pression effective de calcul est limitée à un maximum de 300 kPa (pression relative). L'appareillage sous enveloppe métallique destiné à une utilisation spéciale, par exemple pour atmosphères inflammables, dans les mines ou à bord des navires, peut faire l'objet d'exigences complémentaires. Il faut que les matériels compris dans l'appareillage sous enveloppe métallique soient conçus et essayés suivant leurs différentes normes respectives. La présente norme complète les normes des matériels spécifiques, concernant leur installation dans les ensembles d'appareillage. Cette norme n'interdit pas que d'autres équipements puissent être incorporés dans la même enveloppe. Dans de tels cas, il faut tenir compte de l'influence de ces équipements sur l'appareillage. Cette première édition de la EN 62271-200 annule et remplace la troisième édition de la EN 60298 parue en 1990 dont elle constitue une révision technique. Cette édition inclut les modifications techniques majeures suivantes par rapport à la troisième édition de la EN 60298: Le fondement des modifications de ce document révisé consiste en la prise en compte du mode d'utilisation actuel de l'appareillage haute tension de moins de 52

High-voltage switchgear and controlgear - Part 200: AC metal-enclosed switchgear and controlgear for rated voltages above 1 kV and up to and including 52 kV

General Information

• Status: Withdrawn
• Publication Date: 26-Feb-2004
• Withdrawal Date: 31-Jan-2007
• ICS: 29.130.10 - High voltage switchgear and controlgear
• Technical Committee: CLC/TC 17AC - High-voltage switchgear and controlgear
• Drafting Committee: IEC/SC 17C - IEC_SC_17C
• Parallel Committee: IEC/SC 17C - IEC_SC_17C
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Start Date: 28-Nov-2014
• Completion Date: 28-Nov-2014
• Ref Project: SIST EN 62271-200:2004 - High-voltage switchgear and controlgear -- Part 200: AC metal-enclosed switchgear and controlgear for rated voltages above 1 kV and up to and including 52 kV

Relations

• Replaces: EN 60298:1996/A11:1999 - A.C. metal-enclosed switchgear and controlgear for rated voltages above 1 kV and up to and including 52 kV
• Effective Date: 29-Jan-2023
• Replaces: EN 60298:1996 - A.C. metal-enclosed switchgear and controlgear for rated voltages above 1 kV and up to and including 52 kV
• Effective Date: 29-Jan-2023
• Replaced By: EN 62271-200:2012 - High-voltage switchgear and controlgear - Part 200: AC metal-enclosed switchgear and controlgear for rated voltages above 1 kV and up to and including 52 kV
• Effective Date: 29-Jan-2023

Standards Content (Sample)

SLOVENSKI SIST EN 62271-200:2004

STANDARD
junij 2004
High-voltage switchgear and controlgear - Part 200: AC metal-enclosed switchgear
and controlgear for rated voltages above 1 kV and up to and including 52 kV
ICS 29.130.10 Referenčna številka
©  Standard je založil in izdal Slovenski inštitut za standardizacijo. Razmnoževanje ali kopiranje celote ali delov tega dokumenta ni dovoljeno

EUROPEAN STANDARD EN 62271-200
NORME EUROPÉENNE
EUROPÄISCHE NORM February 2004

ICS 29.130.19 Supersedes EN 60298:1996 + A11:1999

English version
High-voltage switchgear and controlgear
Part 200: AC metal-enclosed switchgear and controlgear
for rated voltages above 1 kV and up to and including 52 kV
(IEC 62271-200:2003)
Appareillage à haute tension Hochspannungs-Schaltgeräte und
Partie 200: Appareillage sous enveloppe -Schaltanlagen
métallique pour courant alternatif Teil 200: Metallgekapselte
de tensions assignées supérieures à 1 kV Wechselstrom-Schaltanlagen für
et inférieures ou égales à 52 kV Bemessungsspannungen über 1 kV bis
(CEI 62271-200:2003) einschließlich 52 kV
(IEC 62271-200:2003)
This European Standard was approved by CENELEC on 2004-02-01. CENELEC members are bound to
comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and
notified to the Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden,
Switzerland and United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Central Secretariat: rue de Stassart 35, B - 1050 Brussels

© 2004 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.

Ref. No. EN 62271-200:2004 E
Foreword
The text of document 17C/311/FDIS, future edition 1 of IEC 62271-200, prepared by SC 17C, High-
voltage switchgear and controlgear assemblies, of IEC TC 17, Switchgear and controlgear, was
submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 62271-200 on
2004-02-01.
This European Standard supersedes EN 60298:1996 + A11:1999.
Significant technical changes with respect to EN 60298:1996 are as follows:
This revised document has been basically changed to be updated to today's use of high-voltage
switchgear and controlgear up to 52 kV. The main changes are: new definitions and classification of
equipment, introduction of internal arc classes (IAC) and its testing.
This standard is to be read in conjunction with EN 60694:1996. Clause numbering follows the clause
numbering of that standard. Additional subclauses, as they relate to a particular clause or subclause
from EN 60694, are numbered 101, 102, etc.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2004-11-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2007-02-01
Annexes ZA and ZB have been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 62271-200:2003 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards indicated:
IEC 60137 NOTE Harmonized as EN 60137:1996 (not modified).
IEC 60517 NOTE Harmonized as HD 358 S3:1992 (not modified).
__________
- 3 - EN 62271-200:2004
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
Publication Year Title EN/HD Year
IEC 60050-151 2001 International Electrotechnical - -
Vocabulary (IEV)
Part 151: Electrical and magnetic
devices
IEC 60050-441 1984 Chapter 441: Switchgear, controlgear - -
and fuses
IEC 60060-1 1989 High-voltage test techniques HD 588.1 S1 1991
+ corr. March 1990 Part 1: General definitions and test
requirements
IEC 60243-1 1998 Electrical strength of insulating EN 60243-1 1998
materials - Test methods
Part 1: Tests at power frequencies

IEC 60265-1 1998 High-voltage switches EN 60265-1 1998
Part 1: Switches for rated voltages
above 1 kV and less than 52 Kv

IEC 60270 2000 High-voltage test techniques - Partial EN 60270 2001
discharge measurements
IEC 60466 1987 AC insulation-enclosed switchgear and - -
controlgear for rated voltages above
1 kV and up to and including 38 kV

IEC 60470 2000 High-voltage alternating current - -
contactors and contactor-based motor-
starters
IEC 60480 1974 Guide to the checking of sulphur - -
hexafluoride (SF6) taken from electrical
equipment
IEC 60529 1989 Degrees of protection provided by EN 60529 1991
enclosures (IP Code) + corr. May 1993

IEC 60694 1996 Common specifications for high-voltage EN 60694 1996
switchgear and controlgear standards + corr. May 1999

Publication Year Title EN/HD Year
IEC 60909-0 2001 Short-circuit currents in three-phase a.c. EN 60909-0 2001
systems
Part 0: Calculation of currents

IEC 60932 1988 Additional requirements for enclosed - -
switchgear and controlgear from 1kV to
72,5 kV to be used in severe climatic
conditions
IEC 61634 1995 High-voltage switchgear and controlgear - -
– Use and handling of sulphur
hexafluoride (SF ) in high-voltage
switchgear and controlgear
IEC 62271-100 2001 High-voltage switchgear and controlgear EN 62271-100 2001
Part 100: High-voltage alternating-
current circuit-breakers
IEC 62271-102 2001 Part 102: High-voltage alternating EN 62271-102 2002
+ corr. April 2002 current disconnectors and earthing
switches
IEC 62271-105 2002 Part 105: Alternating current switch-fuse EN 62271-105 2003
combinations
ISO/IEC Guide 51 1999 Safety aspects - Guidelines for their - -
inclusion in standards
- 5 - EN 62271-200:2004
Annex ZB
(informative)
A-deviations
A-deviation: National deviation due to regulations, the alteration of which is for the time being outside
the competence of the CENELEC member.
This European Standard does not fall under any Directive of the EC.
In the relevant CENELEC countries these A-deviations are valid instead of the provisions of the
European Standard until they have been removed.
Clause Deviation
1 Italy (Italian pressure vessel code for electrical switchgear DM 1 December 1980 and
DM 10 September 1981 published in Gazzetta Ufficiale n° 285 dated 16.10.1981)
For metal-enclosed switchgear and controlgear containing gas-filled compartments,
the design pressure is limited to a maximum of 0,5 bar (gauge) and the volume is
limited to a maximum of 2 m . Gas filled compartments having a design pressure
exceeding 0,5 bar (gauge) or a volume exceeding 2 m shall be designed according
to the Italian pressure vessel code for electrical switchgear.

IEC 62271-200
Edition 1.0 2003-11
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
High-voltage switchgear and controlgear –
Part 200: AC metal-enclosed switchgear and controlgear for rated voltages
above 1 kV and up to and including 52 kV

Appareillage à haute tension –
Partie 200: Appareillage sous enveloppe métallique pour courant alternatif
de tensions assignées supérieures à 1 kV et inférieures ou égales à 52 kV

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
XC
CODE PRIX
ICS 29.130.10 ISBN 2-8318-7240-5

62271-200 © IEC:2003 – 3 –
– 2 – 62271-200 © IEC:2003
CONTENTS
FOREWORD .5
1 General.9
1.1 Scope .9
1.2 Normative references.10
2 Normal and special service conditions .11
3 Terms and definitions.11
4 Ratings .17
4.1 Rated voltage (U ).17
r
4.2 Rated insulation level.17
4.3 Rated frequency (f ) .17
r
4.4 Rated normal current and temperature rise .17
4.5 Rated short-time withstand current (I ) .18
k
4.6 Rated peak withstand current (I ).18
p
4.7 Rated duration of short circuit (t ).18
k
4.8 Rated supply voltage of closing and opening devices and of auxiliary and
control circuits (U ) .18
a
4.9 Rated supply frequency of closing and opening devices and of auxiliary
circuits.18
4.10 Rated pressure of compressed gas supply for insulation and/or operation.18
4.10.1 Rated filling level (of fluid-filled compartments).18
5 Design and construction.19
5.1 Requirements for liquids in switchgear and controlgear .19
5.2 Requirements for gases in switchgear and controlgear .19
5.3 Earthing.19
5.4 Auxiliary and control equipment.21
5.5 Dependent power operation .21
5.6 Stored energy operation.21
5.7 Independent manual operation .21
5.8 Operation of releases.21
5.9 Low- and high-pressure interlocking and monitoring devices.21
5.10 Nameplates .21
5.11 Interlocking devices .22
5.12 Position indication.23
5.13 Degrees of protection by enclosures.23
5.14 Creepage distances .23
5.15 Gas and vacuum tightness .23
5.16 Liquid tightness.24
5.17 Flammability .24
5.18 Electromagnetic compatibility (EMC) .24
6 Type tests .30
6.1 General .30
6.2 Dielectric tests .32
6.3 Radio interference voltage (r.i.v.) test.35
6.4 Measurement of the resistance of circuits.36
6.5 Temperature-rise tests.38
6.6 Short-time withstand current and peak withstand current tests.37

62271-200 © IEC:2003 – 5 –
62271-200 © IEC:2003 – 3 –
6.7 Verification of the protection.39
6.8 Tightness tests .39
6.9 Elect
...