iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
IEC

IEC TS 60695-11-21:2005

(Main)

Fire hazard testing - Part 11-21: Test flames - 500 W vertical flame test method for tubular polymeric materials

Fire hazard testing - Part 11-21: Test flames - 500 W vertical flame test method for tubular polymeric materials

Describes a small-scale laboratory procedure for determining the comparative burning characteristics of tubular polymeric materials. A flame is applied to test specimens held in a vertical position, supported by a wire or mandrel. Upon removal of the test flame, the extinguishing times and the burning characteristics are determined. This test method can be used to compare the burning characteristics of tubular polymeric materials. This test method shall not be used to compare the burning characteristics of any wire or cable products or any cable management systems. This test method can be used to compare the relative performance of materials, to aid in material selection, for quality control purposes and for quality assurance.

Essais relatifs aux risques du feu - Partie 11-21: Flammes d'essai - Méthode d'essai à la flamme verticale de 500 W pour matériaux tubulaires polymères

Décrit une procédure de laboratoire à petite échelle pour déterminer les caractéristiques de combustion comparatives des matériaux polymères tubulaires. Une flamme est appliquée à des éprouvettes maintenues en position verticale, soutenues par un fil ou un mandrin. Après le retrait de la flamme d'essai, les temps d'extinction et les caractéristiques de combustion sont déterminés. Cette méthode d'essai peut être utilisée pour comparer les caractéristiques de combustion des matériaux polymères tubulaires. Cette méthode d'essai ne doit pas être utilisée pour comparer les caractéristiques de combustion des fils ou des câbles ou de tout système de gestion de câbles. Cette méthode d'essai peut être utilisée pour comparer les performances relatives des matériaux, pour aider dans le cadre de la sélection des matériaux, à des fins de contrôle de la qualité et pour l'assurance de la qualité.

General Information

Status
Published
Publication Date
03-May-2005
ICS
01 - GENERALITIES. TERMINOLOGY. STANDARDIZATION. DOCUMENTATION
13.220.40 - Ignitability and burning behaviour of materials and products
29.020 - Electrical engineering in general
Technical Committee
TC 89 - Fire hazard testing
Current Stage
PPUB - Publication issued
Start Date
30-Jun-2005
Completion Date
04-May-2005
Ref Project

Buy Standard

IEC TS 60695-11-21:2005 - Fire hazard testing - Part 11-21: Test flames - 500 W vertical flame test method for tubular polymeric materialsIEC TS 60695-11-21:2005 - Fire hazard testing - Part 11-21: Test flames - 500 W vertical flame test method for tubular polymeric materials
PreviousNext
Technical specification
IEC TS 60695-11-21:2005 - Fire hazard testing - Part 11-21: Test flames - 500 W vertical flame test method for tubular polymeric materials
English and French language
27 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

SPÉCIFICATION CEI
TECHNIQUE
IEC



TS 60695-11-21
TECHNICAL


Première édition
SPECIFICATION
First edition
2005-05

PUBLICATION FONDAMENTALE DE SÉCURITÉ
BASIC SAFETY PUBLICATION
Essais relatifs aux risques du feu –
Partie 11-21:
Flammes d'essai –
Méthode d'essai à la flamme verticale de 500 W
pour matériaux tubulaires polymères

Fire hazard testing –
Part 11-21:
Test flames –
500 W vertical flame test method
for tubular polymeric materials

Numéro de référence
Reference number
CEI/IEC/TS 60695-11-21:2005

---------------------- Page: 1 ----------------------
Numérotation des publications Publication numbering
Depuis le 1er janvier 1997, les publications de la CEI As from 1 January 1997 all IEC publications are
sont numérotées à partir de 60000. Ainsi, la CEI 34-1 issued with a designation in the 60000 series. For
devient la CEI 60034-1. example, IEC 34-1 is now referred to as IEC 60034-1.
Editions consolidées Consolidated editions
Les versions consolidées de certaines publications de la The IEC is now publishing consolidated versions of its
CEI incorporant les amendements sont disponibles. Par publications. For example, edition numbers 1.0, 1.1
exemple, les numéros d’édition 1.0, 1.1 et 1.2 indiquent and 1.2 refer, respectively, to the base publication,
respectivement la publication de base, la publication de the base publication incorporating amendment 1 and
base incorporant l’amendement 1, et la publication de the base publication incorporating amendments 1
base incorporant les amendements 1 et 2. and 2.
Informations supplémentaires Further information on IEC publications
sur les publications de la CEI
Le contenu technique des publications de la CEI est The technical content of IEC publications is kept
constamment revu par la CEI afin qu'il reflète l'état under constant review by the IEC, thus ensuring that
actuel de la technique. Des renseignements relatifs à the content reflects current technology. Information
cette publication, y compris sa validité, sont dispo- relating to this publication, including its validity, is
nibles dans le Catalogue des publications de la CEI available in the IEC Catalogue of publications
(voir ci-dessous) en plus des nouvelles éditions, (see below) in addition to new editions, amendments
amendements et corrigenda. Des informations sur les and corrigenda. Information on the subjects under
sujets à l’étude et l’avancement des travaux entrepris consideration and work in progress undertaken by the
par le comité d’études qui a élaboré cette publication, technical committee which has prepared this
ainsi que la liste des publications parues, sont publication, as well as the list of publications issued,
également disponibles par l’intermédiaire de: is also available from the following:
• Site web de la CEI (www.iec.ch) • IEC Web Site (www.iec.ch)
• Catalogue des publications de la CEI • Catalogue of IEC publications
Le catalogue en ligne sur le site web de la CEI The on-line catalogue on the IEC web site
(www.iec.ch/searchpub) vous permet de faire des (www.iec.ch/searchpub) enables you to search by a
recherches en utilisant de nombreux critères, variety of criteria including text searches,
comprenant des recherches textuelles, par comité technical committees and date of publication. On-
d’études ou date de publication. Des informations en line information is also available on recently
ligne sont également disponibles sur les nouvelles issued publications, withdrawn and replaced
publications, les publications remplacées ou retirées, publications, as well as corrigenda.
ainsi que sur les corrigenda.
• IEC Just Published • IEC Just Published
Ce résumé des dernières publications parues This summary of recently issued publications
(www.iec.ch/online_news/justpub) est aussi dispo- (www.iec.ch/online_news/justpub) is also available
nible par courrier électronique. Veuillez prendre by email. Please contact the Customer Service
contact avec le Service client (voir ci-dessous) Centre (see below) for further information.
pour plus d’informations.
• Service clients • Customer Service Centre
Si vous avez des questions au sujet de cette If you have any questions regarding this
publication ou avez besoin de renseignements publication or need further assistance, please
supplémentaires, prenez contact avec le Service contact the Customer Service Centre:
clients:
Email: custserv@iec.ch Email: custserv@iec.ch
Tél: +41 22 919 02 11 Tel: +41 22 919 02 11
Fax: +41 22 919 03 00 Fax: +41 22 919 03 00
.

---------------------- Page: 2 ----------------------
SPÉCIFICATION CEI
TECHNIQUE
IEC



TS 60695-11-21
TECHNICAL


Première édition
SPECIFICATION

First edition

2005-05


PUBLICATION FONDAMENTALE DE SÉCURITÉ
BASIC SAFETY PUBLICATION
Essais relatifs aux risques du feu –
Partie 11-21:
Flammes d'essai –
Méthode d'essai à la flamme verticale de 500 W
pour matériaux tubulaires polymères

Fire h
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

IEC
IEC TS 60695-1-14:2017(Main)
Fire hazard testing - Part 1-14: Guidance on the different levels of power and energy related to the probability of ignition and fire in low voltage electrotechnical products

IEC TS 60695-1-14:2017(E) provides guidance about the levels of power and energy that could cause ignition and fire in a low voltage electrotechnical product. It can be used by Product Committees to determine what fire hazard safeguards might be used, based on the electrical energy that could be dissipated as heat.
This document deals with products used in normal atmospheres commonly available in the home and does not deal with special locations such as those in explosive atmospheres. It is intended as guidance to IEC committees, and is intended be used with respect to their individual applications.
It has the status of a basic safety publication in accordance with IEC Guide 104 and ISO/IEC Guide 51.
This basic safety publication is intended for use by technical committees in the preparation of standards in accordance with the principles laid down in IEC Guide 104 and ISO/IEC Guide 51.
Key words: Fire Hazard, Probability of Ignition, Power and Energy Levels

  • Technical specification
    15 pages
    English language
    sale 15% off
IEC
IEC 60695-1-30:2017(Main)
Fire hazard testing - Part 1-30: Guidance for assessing the fire hazard of electrotechnical products - Preselection testing process - General guidelines

IEC 60695-1-30:2017 provides guidance for assessing and choosing candidate materials, components or sub-assemblies for making an end product based upon preselection testing.
It describes how preselection provides comparative fire hazard test methods to evaluate the performance of a test specimen and how preselection can be used in the selection of materials, parts, components and sub-assemblies during the design stage of an end product. It further describes how standardized test methods may be used as one part in the decision making processes directed to minimize the fire hazards from electrotechnical equipment. It takes into account the desired reaction to fire properties of the end product, and the possible effects of environmental conditions on the behaviour of the end product.
This third edition cancels and replaces the second edition published in 2008. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
- Reference to IEC 60695-1-12;
- Modified Introduction;
- Clause 2: updated and additional normative references;
- Clause 3: updated and additional terms and definitions;
- Clause 4: updated text, with a requirement and normative reference to IEC 60695-1-10, IEC 60695-1-11 and IEC 60695-1-12;
- Clause 5: modified text;
- Annex A: updated references with additions and deletions;
- Annex B: Examples of materials used in attended appliances replaces the previous example of an ITE product and the Bibliographic references updated.
It has the status of a basic safety publication in accordance with IEC Guide 104 and ISO/IEC Guide 51.
This standard is to be used in conjunction with IEC 60695-1-10:2016 and IEC 60695-1-11:2014.
This basic safety publication is intended for use by technical committees in the preparation of standards in accordance with the principles laid down in IEC Guide 104 and ISO/IEC Guide 51.

  • Standard
    31 pages
    English and French language
    sale 15% off
IEC
IEC 60695-11-5:2016(Main)
Fire hazard testing - Part 11-5: Test flames - Needle-flame test method - Apparatus, confirmatory test arrangement and guidance

IEC 60695-11-5:2016 is also available as IEC 60695-11-5:2016 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.
IEC 60695-11-5:2016 specifies a needle-flame test to simulate the effect of a small flame which may result from fault conditions, in order to assess the fire hazard by a simulation technique. The results of this test may be used as elements of a fire hazard assessment which takes into account all of the factors which are pertinent to an assessment of the fire hazard of a particular end use. It is applicable to electrotechnical equipment, its sub-assemblies and components and to solid electrical insulating materials or other combustible materials. This second edition cancels and replaces the first edition published in 2004. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
- The scope has been broadened to allow this test method to also simulate the effects of small flames from outside the equipment;
- Propane and butane gas are the specified fuel source with a minimum purity of 95 %;
- A new concept has been added which allows the burner to be moved during the test to avoid dripping material from falling onto the tip of the burner tube;
- The burner tube material is now a referenced source;
- The reference for the copper block material has changed - the ISO publication (ISO 1337) has been withdrawn with no replacement. A new callout is now used and Informative Annex C and a bibliography have been added. This basic safety publication is intended for use by technical committees in the preparation of standards in accordance with the principles laid down in IEC Guide 104 and ISO/IEC Guide 51.

  • Standard
    45 pages
    English and French language
    sale 15% off
IEC
IEC 60695-1-10:2016(Main)
Fire hazard testing - Part 1-10: Guidance for assessing the fire hazard of electrotechnical products - General guidelines

IEC 60695-1-10:2016 provides general guidance with respect to fire hazard testing on how to reduce to a tolerable level the risk of fire and the potential effects of fires involving electrotechnical products. It also serves as a signpost standard to the other guidance publications in the IEC 60695 series. It does not give guidance on the use of fire-resistant compartment boundaries or on the use of detection and suppression systems for the mitigation of fire risk. It describes the relationship between fire risk and the potential effects of fire, and provides guidance to IEC product committees on the applicability of qualitative and quantitative fire tests to the fire hazard assessment of electrotechnical products. Details of the calculation of fire risk are not included in the scope of this document. It emphasises the importance of the scenario approach to fire hazard and risk assessment and discusses criteria intended to ensure the development of technically sound hazard-based fire test methods. It discusses the different types of fire tests, in particular the nature of qualitative and quantitative fire tests. It also describes the circumstances under which it is appropriate for IEC product committees to maintain or develop qualitative fire tests. This standard is intended as guidance to IEC committees, and is to be used with respect to their individual applications. This second edition cancels and replaces the first edition published in 2009. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
- reference to IEC 60695-1-12;
- modified Introduction and Scope;
- updated normative references;
- updated terms and definitions;
- modified Table 1;
- addition of Table 2;
- new text in Subclauses 5.2, 5.3 and 5.4;
- mandatory text in Clause 8;
- Annex B changed to Annex A, and modified;
- new Annex B concerning common ignition sources.
This publication is to be read in conjunction with IEC 60695-1-11:2014 and IEC 60695-1-12:2015.
Key words: Fire Hazard, Fire Risk, Fire Safety Engineering

  • Standard
    49 pages
    English and French language
    sale 15% off
IEC
IEC 60695-8-2:2016(Main)
Fire hazard testing - Part 8-2: Heat release - Summary and relevance of test methods

IEC 60695-8-2:2016 presents a summary of published test methods that are relevant to the determination of the heat released in fire tests on electrotechnical products or materials from which they are formed. It represents the current state of the art of the test methods and, where available, includes special observations on their relevance and use. The list of test methods is not to be considered exhaustive, and test methods that were not developed by the IEC are not to be considered as endorsed by the IEC unless this is specifically stated. Heat release data can be used as part of fire hazard assessment and in fire safety engineering, as discussed in IEC 60695-1-10, IEC 60695-1-11 and IEC 60695-1-12. This standard is to be used in conjunction with IEC 60695-8-1.
Key words: Fire Hazard, Heat Release, Fire Safety Engineering, Test Methods

  • Standard
    54 pages
    English and French language
    sale 15% off
IEC
IEC 60695-8-1:2016(Main)
Fire hazard testing - Part 8-1: Heat release - General guidance

IEC 60695-8-1:2016 provides guidance on the measurement and interpretation of heat release from electrotechnical products and materials from which they are constructed. Heat release data can be used as part of fire hazard assessment and in fire safety engineering, as described in IEC 60695-1-11 and IEC 60695-1-12. This third edition cancels and replaces the second edition published in 2008. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
- a modified Introduction;
- reference to IEC 60695-1-12;
- updated normative references;
- revised terms and definitions;
- new text in 4.2.2, 4.2.3, 6.1 and 6.4, including several mandatory statements and
- mandatory statements in a new Subclause 6.5. This standard is to be used in conjunction with IEC 60695-8-2.
Key words: Fire Hazard, Heat Release, Fire Safety Engineering

  • Standard
    54 pages
    English and French language
    sale 15% off
IEC
IEC 60695-10-3:2016(Main)
Fire hazard testing - Part 10-3: Abnormal heat - Mould stress relief distortion test

IEC 60695-10-3:2016 specifies a mould stress relief distortion test. It is applicable to electrotechnical equipment including parts made from polymeric materials. This test method is intended to evaluate the effects caused by relief of the residual process-induced stress, set in a moulded polymeric assembly of an end product. This stress relief occurs when the sample (energized or not), is exposed to conditioning at a defined temperature for a defined period of time. The test specimen is considered to have satisfactorily withstood the test if, after conditioning to room temperature, it meets defined test criteria. This basic safety publication is primarily intended for use by technical committees in the preparation of standards in accordance with the principles laid down in IEC Guide 104 and ISO/IEC Guide 51. It is not intended for use by manufacturers or certification bodies. This second edition of IEC 60695-10-3 cancels and replaces the first edition issued in 2002. It constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
- Updated references;
- Updated equipment;
- Added terms and definitions;
- and added Bibliography. Key words: Fire Hazard, Abnormal Heat, Fire Safety Engineering, Mould Stress Relief Distortion Test.

  • Standard
    21 pages
    English and French language
    sale 15% off
IEC
IEC 60695-1-21:2016(Main)
Fire hazard testing - Part 1-21: Guidance for assessing the fire hazard of electrotechnical products - Ignitability - Summary and relevance of test methods

IEC 60695-1-21:2016 provides a summary of test methods that are used to determine the ignitability of electrotechnical products or materials from which they are formed. It also includes test methods in which, by design, ignitability is a significant quantifiable characteristic. It represents the current state of the art of the test methods and, where available, includes special observations on their relevance and use. The list of test methods is not to be considered exhaustive, and test methods which were not developed by the IEC are not to be considered as endorsed by the IEC unless this is specifically stated. This basic safety publication is primarily intended for use by technical committees in the preparation of standards in accordance with IEC Guide 104 and ISO/IEC Guide 51. It is not intended for use by manufacturers or certification bodies. This first edition of IEC 60695-1-21 cancels and replaces the first edition of IEC TR 60695-1-21 published in 2008. It constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
- Change from a TR to an international standard;
- Modified Introduction;
- Modified Scope;
- Updated normative references;
- Updated terms and definitions;
- Updates and new text in Clause 4;
- Addition of text concerning ASTM D 3638;
- Updates to Annex A and Updates to the bibliography. Key words: Fire Hazard, Fire Safety Engineering, Ignitability.

  • Standard
    69 pages
    English and French language
    sale 15% off
IEC
IEC 60695-1-20:2016(Main)
Fire hazard testing - Part 1-20: Guidance for assessing the fire hazard of electrotechnical products - Ignitability - General guidance

IEC 60695-1-20:2016 provides guidance on the ignitability of electrotechnical products and the materials from which they are formed. It gives guidance on the principles of ignitability; the selection of appropriate test methods and the use and interpretation of results. This first edition of IEC 60695-1-20 cancels and replaces the first edition of IEC TS 60695-1-20 published in 2008. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
- ISO 5660-1 has been added to the normative references;
- definitions of pyrolysis and short-circuit have been added to Clause 3;
- some text from the introduction has been moved to Clause 5 and is now part of the normative text and Clause 5 now contains several mandatory statements. This part of IEC 60695 is intended for use by technical committees in preparation of standards in accordance with IEC Guide 104 and ISO/IEC Guide 51. Key words: Fire Hazard, Fire Test Method, Fire Safety Engineering, Ignitability.

  • Standard
    46 pages
    English and French language
    sale 15% off
IEC
IEC 60695-11-20:2015(Main)
Fire hazard testing - Part 11-20: Test flames - 500 W flame test method

IEC 60695-11-20:2015 describes a test method consisting of two small-scale laboratory test procedures which is intended to compare the burning behaviour of different materials used in electrotechnical products. Vertically oriented bar specimens or horizontally oriented plate test specimens are exposed to a small flame ignition source with a nominal thermal power of 500 W. The test method uses two test specimen configurations to classify material performance. Rectangular bar-shaped test specimens are used to assess ignitability and burning behaviour, and square plate test specimens are used to assess the resistance of the test specimen to burn-through, as defined in 8.3.3. This test method only applies to materials that have been classified as V-0 or V-1 according to IEC 60695-11-10. This test method is only applicable to solid and cellular materials that have an apparent density of more than 250 kg/m3, determined in accordance with ISO 845. The method does not apply to materials that shrink away from the applied flame without igniting due to their thinness. The test method described provides classifications which may be used for quality assurance, the pre-selection of component materials of products, or to verify the required minimum flammability classification of materials used in end products. If used for pre-selection, then positive results shall be obtained at a test specimen thickness which equals the smallest thickness used in the product application. The results obtained provide some information about the behaviour of materials in service, but cannot by themselves assure safe performance in service. This second edition cancels and replaces the consolidated version of IEC 60695-11-20 published in 2003. This edition constitutes a technical revision. The main changes with respect to the first edition are as follows:
- The Part title has been modified to the singular - 500 W flame test method;
- Editorial changes have been made throughout the document for the purpose of aligning IEC 60695-11-10 with IEC 60695-11-20;
- The Introduction has been modified to clarify the description of the test method;
- The Scope has been modified for clarification;
- All occurrences of the term "fixture" have been deleted from the document;
- Preferred thickness values have been added to 7.2 and 7.3;
- 7.4.4: 'Thickness measurement' is now numbered 7.5 to which a new Table 1 - Thickness tolerances has been added;
- New Subclause 8.1.4 'Conditioning of the cotton pad' has been added;
- 8.2.3 clarifies the application of the test flame to distorted specimens;
- Explanatory notes have been added to Figures 5 and 6 and the Bibliography has been updated and references added. This basic safety publication is intended for use by technical committees in the preparation of standards in accordance with IEC Guide 104 and ISO/IEC Guide 51. Key words: Test flames,Fire Hazard, Fire Test Method
This publication is to be read in conjunction with IEC 60695-11-3:2012. The contents of the corrigendum of January 2016 have been included in this copy.

  • Standard
    64 pages
    English and French language
    sale 15% off