IEC 61188-5-4:2007
(Main)Printed boards and printed board assemblies - Design and use - Part 5-4: Attachment (land/joint) considerations - Components with J leads on two sides
Printed boards and printed board assemblies - Design and use - Part 5-4: Attachment (land/joint) considerations - Components with J leads on two sides
IEC 61188-5-4:2007 provides the component and land pattern dimensions for small outline integrated circuits with "J" leads on two sides (SOJ components) used in the reflow soldering process. Basic construction of the SOJ device is also covered. Clause 4 lists the tolerances and target solder joint dimensions used to arrive at the land pattern dimensions.
Cartes imprimées et cartes imprimées équipées - Conception et utilisation - Partie 5-4: Considérations sur les liaisons pistes-soudures - Composants à sorties en J sur deux côtés
La CEI 61188-5-4:2007 fournit les dimensions des composants et des plages d'accueil des circuits intégrés à faible encombrement ayant des soties en J sur les deux côtés (composants SOJ) utilisés dans le procédé de brasage par fusion. La construction de base des systèmes SOJ est également couverte. L'article 4 énumère les tolérances et les dimensions de référence des joints de brasure utilisés pour parvenir aux dimensions des plages d'accueil.
General Information
Relations
Buy Standard
Standards Content (Sample)
IEC 61188-5-4
Edition 1.0 2007-10
INTERNATIONAL
STANDARD
Printed boards and printed board assemblies – Design and use –
Part 5-4: Attachment (land/joint) considerations – Components with J leads on
two sides
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester.
If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication,
please contact the address below or your local IEC member National Committee for further information.
IEC Central Office
3, rue de Varembé
CH-1211 Geneva 20
Switzerland
Email: inmail@iec.ch
Web: www.iec.ch
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.
About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.
ƒ Catalogue of IEC publications: www.iec.ch/searchpub
The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,…).
It also gives information on projects, withdrawn and replaced publications.
ƒ IEC Just Published: www.iec.ch/online_news/justpub
Stay up to date on all new IEC publications. Just Published details twice a month all new publications released. Available
on-line and also by email.
ƒ Electropedia: www.electropedia.org
The world's leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions
in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical
Vocabulary online.
ƒ Customer Service Centre: www.iec.ch/webstore/custserv
If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service
Centre FAQ or contact us:
Email: csc@iec.ch
Tel.: +41 22 919 02 11
Fax: +41 22 919 03 00
IEC 61188-5-4
Edition 1.0 2007-10
INTERNATIONAL
STANDARD
Printed boards and printed board assemblies – Design and use –
Part 5-4: Attachment (land/joint) considerations – Components with J leads on
two sides
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
PRICE CODE
P
ICS 31.180 ISBN 2-8318-9341-0
– 2 – 61188-5-4 © IEC:2007(E)
CONTENTS
FOREWORD.3
INTRODUCTION.5
1 Scope.6
2 Normative references .6
3 General information.6
3.1 General component description .6
3.2 Marking .7
3.3 Packaging .7
3.4 Process considerations .7
4 Small outlined J packages (SOJ) .7
4.1 Component description.7
4.2 Component dimensions .8
4.3 Solder joint fillet design .9
4.4 Land pattern dimensions .11
Bibliography.15
Figure 1 – SOJ construction.8
Figure 2 – SOJ component dimensions .9
Figure 3 – Solder joint fillet design.11
Figure 4 – SOJ land pattern dimensions .14
61188-5-4 © IEC:2007(E) – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
___________
PRINTED BOARDS AND PRINTED BOARD ASSEMBLIES –
DESIGN AND USE –
Part 5-4: Attachment (land/joint) considerations –
Components with J leads on two sides
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with an IEC Publication.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 61188-5-4 has been prepared by IEC technical committee 91:
Electronics assembly technology
The text of this standard is based on the following documents:
FDIS Report on voting
91/703/FDIS 91/735/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
A list of all parts of the IEC 61188 series, under the general title Printed boards and printed
board assemblies – Design and use, can be found on the IEC website.
– 4 – 61188-5-4 © IEC:2007(E)
The committee has decided that the contents of this publication will remain unchanged until
the maintenance result date indicated on the IEC web site under "http://webstore.iec.ch" in
the data related to the specific publication. At this date, the publication will be
• reconfirmed;
• withdrawn;
• replaced by a revised edition, or
• amended.
A bilingual version of this standard may be issued at a later date.
61188-5-4 © IEC:2007(E) – 5 –
INTRODUCTION
This part of IEC 61188 covers land pattern for components with J leads on two sides.
The proposed land pattern dimensions in this standard are based upon the fundamental
tolerance calculation combined with the given land protrusions and courtyard excesses (see
IEC 61188-5-1, Generic requirements). The courtyard includes all issues of the normal
manufacturing necessities.
The unaltered land pattern dimensions of this part are generally applicable for the solder
paste application plus reflow soldering process. For application of the wave soldering process
(though uncommon for SOJ components) the land pattern and courtyard dimensions may
have to be modified. An orientation parallel to the wave direction is strongly recommended
and suitably dimensioned solder thieves should be added.
This standard offers a threefold land pattern dimensioning (levels 1, 2, 3) on the basis of a
threefold set of land protrusions and courtyard excesses: maximum (max.); medium (mdn);
and minimum (min.). Nevertheless the user may develop deviating land pattern dimensions
based upon the methodology of IEC 61188-5-1, introducing his own special material and
assembling process conditions C, F, P and perhaps his own special land protrusions and
courtyard excesses dimensions, as required.
If a user has good reasons to use a concept different from that of IEC 61188-5-1 or if the user
prefers unusual land protrusions, this standard should be used for checking the resulting
solder fillets.
It is the responsibility of the user to verify his used SMD land patterns for achieving an
undisturbed mounting process including testing and an ensured reliability for the product
stress conditions in use.
– 6 – 61188-5-4 © IEC:2007(E)
PRINTED BOARDS AND PRINTED BOARD ASSEMBLIES –
DESIGN AND USE –
Part 5-4: Attachment (land/joint) considerations –
Components with J leads on two sides
1 Scope
This part of IEC 61188 provides the component and land pattern dimensions for small outline
integrated circuits with “J“ leads on two sides (SOJ components) used in the reflow soldering
process. Basic construction of the SOJ device is also covered. Clause 4 lists the tolerances
and target solder joint dimensions used to arrive at the land pattern dimensions.
2 Normative references
The following referenced documents are indispensable for the application of this document.
For dated references, only the edition cited applies. For undated references, the latest edition
of the referenced document (including any amendments) applies.
IEC 60068-2-58, Environmental testing – Part 2-58: Tests: Test Td. Test methods for
solderability, resistance to dissolution of metallization and to soldering heat of surface
mounting devices (SMD)
IEC 60286-3, Packaging of components for automatic handling – Part 3: Packaging of surface
mount components on continuous tapes
IEC 60286-4, Packaging of components for automatic handling – Part 4: Stick magazines for
electronic components encapsulated in packages of form E and G
IEC 60286-5, Packaging of components for automatic handling – Part 5: Matrix trays
IEC 61760-1, Surface mounting technology – Part 1: Standard method for the specification of
surface mounting components (SMDs)
3 General information
3.1 General component description
The two-sided J lead family is a small outline family identified by the dimensions of the body
size in inches. For example, the SOJ/300 has a body size of 0,300 in or 7,63 mm, the
SOJ/350 has a body size of 0,350 in or 8,88 mm, the SOJ/400 has a body size of 0,400 in or
10,12 mm, and the SOJ/450 has a body size of 0,450 in or 11,38 mm. Package lead counts
range from 14 to 28 pins. Pitch is uniformly for all sizes, i.e. 1,27 mm.
The small-outline J (SOJ) package has leads on two sides, similar to a DIP. The lead
configuration, like the letter J, extends out the side of the package and bends under the
package forming a J bend. The point of contact of the lead to the land pattern is at the apex of
the J bend and is the basis for the span of the land pattern.
The (inner) end of the J is called the heel, and the outer side of the J is called the toe.
61188-5-4 © IEC:2007(E) – 7 –
The leads shall be coplanar within 0,1 mm. That is, when the component is placed on a flat
surface, no lead may be more than 0,1 mm off the flat surface.
The SOJ package takes advantage of chips having parallel address or data line layouts. For
example, memory ICs are often used in multiples, and bus lines connect to the same pin on
each chip. Memory chips in SOJ packages can be placed close to one another because of the
parallel pin layout and the use of J leads. With high capacity memory systems, the space
savings can be significant compared with a dual in-line.
3.2 Marking
The marking of the SOIC family of parts shall comply with
...
IEC 61188-5-4 ®
Edition 1.0 2007-10
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Printed boards and printed board assemblies – Design and use –
Part 5-4: Attachment (land/joint) considerations – Components with J leads on
two sides
Cartes imprimées et cartes imprimées équipées – Conception et utilisation –
Partie 5-4: Considérations sur les liaisons pistes-soudures – Composants à
sorties en J sur deux côtés
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by
any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or
IEC's member National Committee in the country of the requester.
If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication,
please contact the address below or your local IEC member National Committee for further information.
Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite
ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie
et les microfilms, sans l'accord écrit de la CEI ou du Comité national de la CEI du pays du demandeur.
Si vous avez des questions sur le copyright de la CEI ou si vous désirez obtenir des droits supplémentaires sur cette
publication, utilisez les coordonnées ci-après ou contactez le Comité national de la CEI de votre pays de résidence.
IEC Central Office
3, rue de Varembé
CH-1211 Geneva 20
Switzerland
Email: inmail@iec.ch
Web: www.iec.ch
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.
About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.
ƒ Catalogue of IEC publications: www.iec.ch/searchpub
The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,…).
It also gives information on projects, withdrawn and replaced publications.
ƒ IEC Just Published: www.iec.ch/online_news/justpub
Stay up to date on all new IEC publications. Just Published details twice a month all new publications released. Available
on-line and also by email.
ƒ Electropedia: www.electropedia.org
The world's leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions
in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical
Vocabulary online.
ƒ Customer Service Centre: www.iec.ch/webstore/custserv
If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service
Centre FAQ or contact us:
Email: csc@iec.ch
Tel.: +41 22 919 02 11
Fax: +41 22 919 03 00
A propos de la CEI
La Commission Electrotechnique Internationale (CEI) est la première organisation mondiale qui élabore et publie des
normes internationales pour tout ce qui a trait à l'électricité, à l'électronique et aux technologies apparentées.
A propos des publications CEI
Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possédez
l’édition la plus récente, un corrigendum ou amendement peut avoir été publié.
ƒ Catalogue des publications de la CEI: www.iec.ch/searchpub/cur_fut-f.htm
Le Catalogue en-ligne de la CEI vous permet d’effectuer des recherches en utilisant différents critères (numéro de référence,
texte, comité d’études,…). Il donne aussi des informations sur les projets et les publications retirées ou remplacées.
ƒ Just Published CEI: www.iec.ch/online_news/justpub
Restez informé sur les nouvelles publications de la CEI. Just Published détaille deux fois par mois les nouvelles
publications parues. Disponible en-ligne et aussi par email.
ƒ Electropedia: www.electropedia.org
Le premier dictionnaire en ligne au monde de termes électroniques et électriques. Il contient plus de 20 000 termes et
définitions en anglais et en français, ainsi que les termes équivalents dans les langues additionnelles. Egalement appelé
Vocabulaire Electrotechnique International en ligne.
ƒ Service Clients: www.iec.ch/webstore/custserv/custserv_entry-f.htm
Si vous désirez nous donner des commentaires sur cette publication ou si vous avez des questions, visitez le FAQ du
Service clients ou contactez-nous:
Email: csc@iec.ch
Tél.: +41 22 919 02 11
Fax: +41 22 919 03 00
IEC 61188-5-4 ®
Edition 1.0 2007-10
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Printed boards and printed board assemblies – Design and use –
Part 5-4: Attachment (land/joint) considerations – Components with J leads on
two sides
Cartes imprimées et cartes imprimées équipées – Conception et utilisation –
Partie 5-4: Considérations sur les liaisons pistes-soudures – Composants à
sorties en J sur deux côtés
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
P
CODE PRIX
ICS 31.180 ISBN 978-2-88910-434-5
– 2 – 61188-5-4 © IEC:2007
CONTENTS
FOREWORD.3
INTRODUCTION.5
1 Scope.6
2 Normative references .6
3 General information.6
3.1 General component description .6
3.2 Marking .7
3.3 Packaging .7
3.4 Process considerations .7
4 Small outlined J packages (SOJ) .7
4.1 Component description.7
4.2 Component dimensions .8
4.3 Solder joint fillet design .9
4.4 Land pattern dimensions .11
Bibliography.15
Figure 1 – SOJ construction.8
Figure 2 – SOJ component dimensions .9
Figure 3 – Solder joint fillet design.11
Figure 4 – SOJ land pattern dimensions .14
61188-5-4 © IEC:2007 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
___________
PRINTED BOARDS AND PRINTED BOARD ASSEMBLIES –
DESIGN AND USE –
Part 5-4: Attachment (land/joint) considerations –
Components with J leads on two sides
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with an IEC Publication.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 61188-5-4 has been prepared by IEC technical committee 91:
Electronics assembly technology
This bilingual version, published in 2009-09, corresponds to the English version.
The text of this standard is based on the following documents:
FDIS Report on voting
91/703/FDIS 91/735/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
The French version of this standard has not been voted upon.
– 4 – 61188-5-4 © IEC:2007
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
A list of all parts of the IEC 61188 series, under the general title Printed boards and printed
board assemblies – Design and use, can be found on the IEC website.
The committee has decided that the contents of this publication will remain unchanged until
the maintenance result date indicated on the IEC web site under "http://webstore.iec.ch" in
the data related to the specific publication. At this date, the publication will be
• reconfirmed;
• withdrawn;
• replaced by a revised edition, or
• amended.
61188-5-4 © IEC:2007 – 5 –
INTRODUCTION
This part of IEC 61188 covers land pattern for components with J leads on two sides.
The proposed land pattern dimensions in this standard are based upon the fundamental
tolerance calculation combined with the given land protrusions and courtyard excesses (see
IEC 61188-5-1, Generic requirements). The courtyard includes all issues of the normal
manufacturing necessities.
The unaltered land pattern dimensions of this part are generally applicable for the solder
paste application plus reflow soldering process. For application of the wave soldering process
(though uncommon for SOJ components) the land pattern and courtyard dimensions may
have to be modified. An orientation parallel to the wave direction is strongly recommended
and suitably dimensioned solder thieves should be added.
This standard offers a threefold land pattern dimensioning (levels 1, 2, 3) on the basis of a
threefold set of land protrusions and courtyard excesses: maximum (max.); medium (mdn);
and minimum (min.). Nevertheless the user may develop deviating land pattern dimensions
based upon the methodology of IEC 61188-5-1, introducing his own special material and
assembling process conditions C, F, P and perhaps his own special land protrusions and
courtyard excesses dimensions, as required.
If a user has good reasons to use a concept different from that of IEC 61188-5-1 or if the user
prefers unusual land protrusions, this standard should be used for checking the resulting
solder fillets.
It is the responsibility of the user to verify his used SMD land patterns for achieving an
undisturbed mounting process including testing and an ensured reliability for the product
stress conditions in use.
– 6 – 61188-5-4 © IEC:2007
PRINTED BOARDS AND PRINTED BOARD ASSEMBLIES –
DESIGN AND USE –
Part 5-4: Attachment (land/joint) considerations –
Components with J leads on two sides
1 Scope
This part of IEC 61188 provides the component and land pattern dimensions for small
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.