IEC 60335-2-103:2015/AMD2:2019

Amendment 2 - Household and similar electrical appliances - Safety - Part 2-103: Particular requirements for drives for gates, doors and windows

Amendment 2 - Appareils électrodomestiques et analogues - Sécurité - Partie 2-103: Exigences particulières pour les motorisations de portails, portes et fenêtres

General Information

• Status: Published
• Publication Date: 27-Nov-2019
• ICS: 01 - GENERALITIES. TERMINOLOGY. STANDARDIZATION. DOCUMENTATION
• ICS: 13.120 - Domestic safety
• ICS: 91.060.50 - Doors and windows
• Technical Committee: TC 61 - Safety of household and similar electrical appliances
• Drafting Committee: MT 25 - TC 61/MT 25

Relations

• Amends: IEC 60335-2-103:2015 - Household and similar electrical appliances - Safety - Part 2-103: Particular requirements for drives for gates, doors and windows
• Effective Date: 05-Sep-2023
• Revised: IEC 60335-2-103:2023 - Household and similar electrical appliances - Safety - Part 2-103: Particular requirements for drives for gates, doors and windows
• Effective Date: 05-Sep-2023

Standards Content (Sample)

IEC 60335-2-103 ®
Edition 3.0 2019-11
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
A MENDMENT 2
AM ENDEMENT 2
Household and similar electrical appliances – Safety –
Part 2-103: Particular requirements for drives for gates, doors and windows

Appareils électrodomestiques et analogues – Sécurité –
Partie 2-103: Exigences particulières pour les motorisations de portails, portes
et fenêtres
IEC 60335-2-103:2015-04/AMD2:2019-11(en-fr)

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester. If you have any questions about IEC
copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or
your local IEC member National Committee for further information.

Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite
ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie
et les microfilms, sans l'accord écrit de l'IEC ou du Comité national de l'IEC du pays du demandeur. Si vous avez des
questions sur le copyright de l'IEC ou si vous désirez obtenir des droits supplémentaires sur cette publication, utilisez
les coordonnées ci-après ou contactez le Comité national de l'IEC de votre pays de résidence.

IEC Central Office Tel.: [phone]
3, rue de Varembé [e-mail]
CH-1211 Geneva 20 www.iec.ch
Switzerland
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.

About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigendum or an amendment might have been published.

IEC publications search - webstore.iec.ch/advsearchform Electropedia - www.electropedia.org
The advanced search enables to find IEC publications by a The world's leading online dictionary on electrotechnology,
variety of criteria (reference number, text, technical containing more than 22 000 terminological entries in English
committee,…). It also gives information on projects, replaced and French, with equivalent terms in 16 additional languages.
and withdrawn publications. Also known as the International Electrotechnical Vocabulary

(IEV) online.
IEC Just Published - webstore.iec.ch/justpublished
Stay up to date on all new IEC publications. Just Published IEC Glossary - std.iec.ch/glossary
details all new publications released. Available online and 67 000 electrotechnical terminology entries in English and
once a month by email. French extracted from the Terms and Definitions clause of
IEC publications issued since 2002. Some entries have been
IEC Customer Service Centre - webstore.iec.ch/csc collected from earlier publications of IEC TC 37, 77, 86 and
If you wish to give us your feedback on this publication or CISPR.

need further assistance, please contact the Customer Service

Centre: [e-mail].
A propos de l'IEC
La Commission Electrotechnique Internationale (IEC) est la première organisation mondiale qui élabore et publie des
Normes internationales pour tout ce qui a trait à l'électricité, à l'électronique et aux technologies apparentées.

A propos des publications IEC
Le contenu technique des publications IEC est constamment revu. Veuillez vous assurer que vous possédez l’édition la
plus récente, un corrigendum ou amendement peut avoir été publié.

Recherche de publications IEC - Electropedia - www.electropedia.org
webstore.iec.ch/advsearchform Le premier dictionnaire d'électrotechnologie en ligne au
La recherche avancée permet de trouver des publications IEC monde, avec plus de 22 000 articles terminologiques en
en utilisant différents critères (numéro de référence, texte, anglais et en français, ainsi que les termes équivalents dans
comité d’études,…). Elle donne aussi des informations sur les 16 langues additionnelles. Egalement appelé Vocabulaire
projets et les publications remplacées ou retirées. Electrotechnique International (IEV) en ligne.

IEC Just Published - webstore.iec.ch/justpublished Glossaire IEC - std.iec.ch/glossary
Restez informé sur les nouvelles publications IEC. Just 67 000 entrées terminologiques électrotechniques, en anglais
Published détaille les nouvelles publications parues. et en français, extraites des articles Termes et Définitions des
Disponible en ligne et une fois par mois par email. publications IEC parues depuis 2002. Plus certaines entrées
antérieures extraites des publications des CE 37, 77, 86 et
Service Clients - webstore.iec.ch/csc CISPR de l'IEC.

Si vous désirez nous donner des commentaires sur cette
publication ou si vous avez des questions contactez-nous:
[e-mail].
IEC 60335-2-103 ®
Edition 3.0 2019-11
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
A MENDMENT 2
AM ENDEMENT 2
Household and similar electrical appliances – Safety –

Part 2-103: Particular requirements for drives for gates, doors and windows

Appareils électrodomestiques et analogues – Sécurité –

Partie 2-103: Exigences particulières pour les motorisations de portails, portes

et fenêtres
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 13.120; 91.060.50 ISBN 978-2-8322-7627-3

–2 – IEC 60335-2-103:2015/AMD2:2019
© IEC 2019
FOREWORD
This amendment has been prepared by IEC technical committee 61: Safety of household and
similar electrical appliances.
The text of this amendment is based on the following documents:
FDIS Report on voting
61/5927/FDIS 61/5943/RVD
Full information on the voting for the approval of this amendment can be found in the report
on voting indicated in the above table.
The committee has decided that the contents of this amendment and the base publication will
remain unchanged until the stability date indicated on the IEC website under
"http://webstore.iec.ch" in the data related to the specific publication. At this date, the
publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
NOTE The attention of National Committees is drawn to the fact that equipment manufacturers and testing
organizations may need a transitional period following publication of a new, amended or revised IEC publication in
which to make products in accordance with the new requirements and to equip themselves for conducting new or
revised tests.
It is the recommendation of the committee that the content of this publication be adopted for implementation
nationally not earlier than 12 months or later than 36 months from the date of publication.

_____________
3 Terms and definitions
Add the following new definitions:
3.113
main closing edge
edge(s) of a pedestrian door leaf, whose distance from a parallel opposing closing edge or
surface determines the usable pathway
3.114
opposing closing edge
edge(s) of a pedestrian door leaf formed by the main closing edge and a fixed edge or a
surface against which the pedestrian door leaf is moving
7 Marking and instructions
7.1 Replace the second paragraph by the following:

© IEC 2019
Drives supplied without a driven part shall be marked with the rated load, in newtons (N) or
in newton-metres (Nm).
Unless the drive is intended for continuous operation, drives supplied without a driven part
shall be marked with the rated operating time in minutes, or the number of cycles per hour,
or the rated number of operating cycles.
7.12 Replace the second paragraph by the following:
The instructions shall state the substance of the following:
– do not allow children to play with fixed controls. Keep remote controls away from children;
– activation of the manual release may cause uncontrolled movement of the driven part due
to mechanical failures or an out-of-balance condition; (if applicable);
– when operating a biased-off switch, make sure that other persons are kept away;
– when closing a window that has been opened by a smoke control system, make sure that
other persons are kept away;
– frequently examine the installation for imbalance where applicable and signs of wear or
damage to cables, springs and mounting. Do not use if repair or adjustment is necessary;
– disconnect the supply(s) when cleaning or other maintenance is being carried out.
The instructions shall include the following information:
– explanation of mode indicators;
– details on how to use any manual release, or reversible drive used as a manual release;
– details on how to re-adjust controls, (if applicable);
– where the operation of the drive is specified in cycles per hour, the rest period required
between cycles.
Add the following new subclause:
7.15 Addition:
The markings shall also be provided with the instructions. In addition, the marking relevant to
name, trademark or identification mark, of the manufacturer or responsible vendor and the
model or type reference can also be retrieved from a label, such as a matrix barcode, visible
on the appliance after installation.
11 Heating
11.7 Replace the text of the replacement by the following:
Drives for continuous operation are operated for consecutive cycles until steady conditions
are established.
Drives not for continuous operation are operated as follows:
– drives for gates for one household and horizontally moving garage doors for one
household are operated without rest periods for three cycles or the rated operating time
or the rated number of operating cycles, whichever is longer;
– drives for windows are operated without rest periods for the rated number of operating
cycles or the rated operating time in minutes;
– others drives are operated without rest periods for four minutes or the rated operating
time or the rated number of operating cycles but for not less than five cycles of
operation, whichever is longer.

–4 – IEC 60335-2-103:2015/AMD2:2019
© IEC 2019
– drives rated in cycles per hour are operated for 20 % more than the rated number of
cycles per hour and with the relevant rest period(s) declared by the manufacturer.
19 Abnormal operation
Add the following new subclause:
19.13 Addition:
If the drive can be operated when any of the fault conditions are simulated, the applicable
tests of BB.20.104, BB.20.107, CC.20.105, DD.20.104 and DD.20.107 are carried out, the
drive, however, being supplied at rated voltage.
Either the drive continues to fulfil the requirements, or, after a maximum of one cycle of
operation, it shall stop with the driven part in a safe position or the drive shall change to a
biased-off switch mode of operation.
25 Supply connection and external flexible cords
Add the following new subclauses:
25.8 Addition:
Supply cords of class III appliances need not comply with Table 11 if the temperature rises
of the cord insulation specified in Table 3 and Table 9 are not exceeded during the tests of
Clause 11 and Clause 19, respectively.
25.15 Addition:
For class III appliances and parts of class III construction that have a rated power input
higher than 15 W, the pull force is 30 N. The test is not carried out on class III appliances or
parts of a class III construction that have a rated power input less than or equal to
15 W.
Annex DD – Drives for horizontally and vertically moving doors and gates
DD.20.107.1.2 Replace the first paragraph by the following:
For vertically moving driven parts, an obstacle having dimensions of approximately 80 mm ×
300 mm and a height of 100 mm with 3 sides (one in each dimension) having a reflective
surface, obtained by use of mirrors, fine grained stainless steel or white-gloss paint, and the
other three sides being non reflective surfaces painted dull-black, is placed on the ground and
centrally along its 300 mm length at any place in the path of the leading edge across the
driven part opening.
Annex GG – Test method of entrapment protection system of drives for
revolving doors
GG.1 Replace “main closing edge” by “main closing edge”.
Replace “opposing closing edge” by “opposing closing edge” in two places.
GG.2 Replace “main closing edge” by “main closing edge”.

© IEC 2019
Replace “opposing closing edge” by “opposing closing edge”.
GG.4 Replace “main closing edge” by “main closing edge”.
Annex HH – Limitation of impact forces of pedestrian doors
Table HH.1 – Permissible dynamic forces
In the table cell headings, replace “Between closing edges and opposing closing edges in
a a
gaps of ” by “Between main closing edges and opposing closing edges in gaps of ”
In table footnote a, replace “opposing closing edge” by “opposing closing edge”.
In table footnote a, replace “main closing edge” by “main closing edge”.
Annex JJ – Low energy movement of pedestrian doors
JJ.1 Replace “main closing edge” by “main closing edge” in three places.

____________
–6 – IEC 60335-2-103:2015/AMD2:2019
© IEC 2019
AVANT-PROPOS
Le présent amendement a été établi par le comité d'études 61 de l’IEC: Sécurité des
appareils électrodomestiques et analogues.
Le texte de cet amendement est issu des documents suivants:
FDIS Rapport de vote
61/5927/FDIS 61/5943/RVD
Le rapport de vote indiqué dans le tableau ci-dessus donne toute information sur le vote ayant
abouti à l'approbation de cet amendement.
Le comité a décidé que le contenu de cet amendement et de la publication de base ne sera
pas modifié avant la date de stabilité indiquée sur le site web de l'IEC sous
"http://webstore.iec.ch" dans les données relatives à la publication
...