ISO 3715-2:2001
(Main)Ships and marine technology — Propulsion plants for ships — Part 2: Vocabulary for controllable-pitch propeller plants
Ships and marine technology — Propulsion plants for ships — Part 2: Vocabulary for controllable-pitch propeller plants
This part of ISO 3715 gives terms and definitions applicable exclusively to continuously variable and hydraulic operated controllable-pitch propeller units. It does not cover controllable-pitch propeller units for which only a few specified pitch settings apply. General vocabulary for the geometry of screw propellers is given in ISO 3715-1 and is also valid for controllablepitch propellers.
Navires et technologie maritime — Installations de propulsion des navires — Partie 2: Vocabulaire pour Installations avec hélice à pas variable
General Information
Relations
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 3715-2
First edition
2001-08-01
Ships and marine technology — Propulsion
plants for ships —
Part 2:
Vocabulary for controllable-pitch propeller
plants
Navires et technologie maritime — Installations de propulsion
des navires —
Partie 2: Vocabulaire pour installations avec hélice à pas variable
Reference number
ISO 3715-2:2001(E)
©
ISO 2001
---------------------- Page: 1 ----------------------
ISO 3715-2:2001(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not
be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this
file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this
area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2001
The reproduction of the terms and definitions contained in this International Standard is permitted in teaching manuals, instruction booklets,
technical publications and journals for strictly educational or implementation purposes. The conditions for such reproduction are: that no
modifications are made to the terms and definitions; that such reproduction is not permitted for dictionaries or similar publications offered for
sale; and that this International Standard is referenced as the source document.
With the sole exceptions noted above, no other part of this publication may be reproduced or utilized in any form or by any means, electronic or
mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in
the country of the requester.
ISO copyright office
Case postale 56 � CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.ch
Web www.iso.ch
Printed in Switzerland
ii © ISO 2001 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 3715-2:2001(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this part of ISO 3715 may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
International Standard ISO 3715-2 was prepared by Technical Committee ISO/TC 8, Ships and marine technology,
Subcommittee SC 3, Piping and machinery.
ISO 3715 consists of the following parts, under the general title Ships and marine technology — Propulsion plants
for ships:
� Part 1: Vocabulary for geometry of propellers
� Part 2: Vocabulary for controllable-pitch propeller plants
© ISO 2001 – All rights reserved iii
---------------------- Page: 3 ----------------------
INTERNATIONAL STANDARD ISO 3715-2:2001(E)
Ships and marine technology — Propulsion plants for ships —
Part 2:
Vocabulary for controllable-pitch propeller plants
Scope
This part of ISO 3715 gives terms and definitions applicable exclusively to continuously variable and hydraulic
operated controllable-pitch propeller units. It does not cover controllable-pitch propeller units for which only a few
specified pitch settings apply.
General vocabulary for the geometry of screw propellers is given in ISO 3715-1 and is also valid for controllable-
pitch propellers.
Normative reference
The following normative document contains provisions which, through reference in this text, constitute provisions of
this part of ISO 3715. For dated references, subsequent amendments to, or revisions of, any of these publications
do not apply. However, parties to agreements based on this part of ISO 3715 are encouraged to investigate the
possibility of applying the most recent edition of the normative document indicated below. For undated references,
the latest edition of the normative document referred to applies. Members of ISO and IEC maintain registers of
currently valid International Standards.
ISO 3715-1, Ships and marine technology — Propulsion plants for ships — Part 1: Vocabulary for geometry of
propellers
Terms and definitions
1
controllable-pitch propeller
screw propeller with controllable pitch of the blades
NOTE Figure 1 shows a controllable-pitch propeller unit and its individual components.
1.1
controllable-pitch reversible propeller
screw propeller with controllable pitch of the blades in positive and negative range of pitch angle
1.2
controllable-pitch non-reversible propeller
screw propeller with controllable-pitch of the blades in the positive range of pitch angle
1.3
controllable-pitch propeller including feathering position
screw propeller with controllable pitch of the blades in positive and negative range of pitch angle and in feathering
position
© ISO 2001 – All rights reserved 1
---------------------- Page: 4 ----------------------
ISO 3715-2:2001(E)
2Blade
See definition in ISO 3715-1.
2.1
blade attachment
component part for force-locking and form-locking connection of a blade with the hub
2.2
bl
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.