iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ISO

ISO 8217:2010/Cor 1:2011

(Corrigendum)

Petroleum products — Fuels (class F) — Specifications of marine fuels — Technical Corrigendum 1

Petroleum products — Fuels (class F) — Specifications of marine fuels — Technical Corrigendum 1

This International Standard specifies the requirements for petroleum fuels for use in marine diesel engines and boilers, prior to appropriate treatment before use. The specifications for fuels in this International Standard can also be applicable to fuels for stationary diesel engines of the same or similar make and type as those used for marine purposes. This International Standard specifies four categories of distillate fuel, one of which is for diesel engines for emergency purposes. It also specifies six categories of residual fuel.

Produits pétroliers — Combustibles (classe F) — Spécifications des combustibles pour la marine — Rectificatif technique 1

Naftni proizvodi - Goriva (razred F) - Specifikacije ladijskih goriv - Tehnični popravek 1

Ta mednarodni standard določa zahteve za naftna goriva za uporabo v ladijskih dizelskih motorjih in kotlih pred ustrezno obdelavo pred uporabo. Specifikacije za goriva v tem mednarodnem standardu se lahko uporabljajo tudi za goriva za stacionarne dizelske motorje iste ali podobne znamke in vrste, kot se uporabljajo v pomorstvu. Ta mednarodni standard določa štiri kategorije destilatov, ena od katerih je za dizelske motorje za nujne primere. Poleg tega določa tudi šest kategorij mazuta.

General Information

Status
Withdrawn
Publication Date
10-Mar-2011
Withdrawal Date
10-Mar-2011
ICS
75.160.20 - Liquid fuels
Technical Committee
ISO/TC 28/SC 4 - Classifications and specifications
Drafting Committee
ISO/TC 28/SC 4/WG 6 - Classification and specification of marine fuels
Current Stage
9599 - Withdrawal of International Standard
Completion Date
07-Aug-2012
Ref Project
SIST ISO 8217:2011/Cor 1:2011 - Petroleum products - Fuels marine fuels - TECHNICAL CORRIGENDUM 1

Relations

Revised
ISO 8217:2012 - Petroleum products — Fuels (class F) — Specifications of marine fuels
Effective Date
12-Mar-2011
Corrects
ISO 8217:2010 - Petroleum products — Fuels (class F) — Specifications of marine fuels
Effective Date
25-Apr-2020

Buy Standard

ISO 8217:2011/Cor 1:2011ISO 8217:2011/Cor 1:2011
PreviousNext
Corrigendum
ISO 8217:2011/Cor 1:2011
English language
1 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Produits pétroliers - Combustibles (classe F) - Spécifications des combustibles pour la marine - RECTIFICATIF TECHNIQUE 1Petroleum products - Fuels marine fuels - TECHNICAL CORRIGENDUM 175.160.20Liquid fuelsICS:Ta slovenski standard je istoveten z:ISO 8217:2010/Cor 1:2011SIST ISO 8217:2011/Cor 1:2011en,fr01-november-2011SIST ISO 8217:2011/Cor 1:2011SLOVENSKI
STANDARDSIST ISO 8217:20061DGRPHãþD



SIST ISO 8217:2011/Cor 1:2011



ICS
75.160.20 Ref. No. ISO 8217:2010/Cor.1:2011(E)©
ISO 2011 – All rights reserved Published in Switzerland
INTERNATIONAL STANDARD ISO 8217:2010 TECHNICAL CORRIGENDU
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ISO
ISO/PAS 23263:2019(Main)
Petroleum products — Fuels (class F) — Considerations for fuel suppliers and users regarding marine fuel quality in view of the implementation of maximum 0,50 % sulfur in 2020

This document addresses quality considerations that apply to marine fuels in view of the implementation of maximum 0,50 mass % S in 2020 and the range of marine fuels that will be placed on the market in response to the international statutory requirements to reduce exhaust gas emissions. It defines general requirements that apply to all 0,50 mass % sulfur (S) fuels and confirms the applicability of ISO 8217 for those fuels. It gives technical considerations which might apply to particular fuels for the following characteristics: — kinematic viscosity; — cold flow properties; — stability; — ignition characteristics; — catalyst fines. Additionally, it provides considerations on the compatibility between fuels and additional information on ISO 8217:2017, Annex B (see Annexes B and D). NOTE 1 For the purposes of this document, 0,50 mass % S fuels refers to distillate and residual fuels with a sulfur content up to 0,50 mass %. NOTE 2 For the purposes of this document, "mass %" and "volume %" are used to represent the mass and volume fractions respectively. NOTE 3 This document can also be used in conjunction with earlier editions of ISO 8217 in the event an earlier edition is referenced in the commercial agreement between parties.

  • Technical specification
    12 pages
    English language
    sale 15% off
  • Technical specification
    12 pages
    French language
    sale 15% off
ISO
ISO 8217:2017(Main)
Petroleum products — Fuels (class F) — Specifications of marine fuels
SIST ISO 8217:2018

ISO 8217:2017 specifies the requirements for fuels for use in marine diesel engines and boilers, prior to conventional onboard treatment (settling, centrifuging, filtration) before use. The specifications for fuels in this document can also be applied to fuels used in stationary diesel engines of the same or similar type as those used for marine purposes. ISO 8217:2017 specifies seven categories of distillate fuels, one of which is for diesel engines used for emergency purposes. It also specifies six categories of residual fuels. For the purposes of this document, the term "fuels" is currently used to include the following: - hydrocarbons from petroleum crude oil, oil sands and shale; - hydrocarbons from synthetic or renewable sources, similar in composition to petroleum distillate fuels; - blends of the above with a fatty acid methyl ester(s) (FAME) component where permitted. NOTE 1 Appropriate guidance about fuel treatment systems for diesel engines is published by the International Council on Combustion Engines (CIMAC)[5]. NOTE 2 Requirements for gas turbine fuels used in marine applications are specified in ISO 4261[6]. NOTE 3 For the purposes of this document, the terms "mass %" and "volume %" are used to represent the mass and volume fractions respectively.

  • Standard
    23 pages
    English language
    sale 15% off
  • Standard
    29 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    24 pages
    French language
    sale 15% off
ISO
ISO 8216-1:2017(Main)
Petroleum products — Fuels (class F) classification — Part 1: Categories of marine fuels

ISO 8216-1:2017 defines the detailed classification of marine fuels within class F (petroleum fuels). It is intended to be read in conjunction with ISO 8216‑99.

  • Standard
    3 pages
    English language
    sale 15% off
  • Standard
    3 pages
    French language
    sale 15% off
ISO
ISO 16861:2015(Main)
Petroleum products — Fuels (class F) — Specifications of dimethyl ether (DME)

ISO 16861:2015 specifies the characteristics of DME used as fuel of which the main component is the dimethyl ether synthesized from any organic raw materials. ISO 16861:2015 is applicable for DME used as heating fuel, industrial fuel, and to replace diesel fuel or gas oil. It does not deal with the possible additives necessary for specific end-use applications, for example, odorant typically added to heating fuel and lubricity improvers for DME used as replacement of diesel. Such additives are typically specified for the different end-use applications, at an appropriate level ? national, regional, or international.

  • Standard
    5 pages
    English language
    sale 15% off
  • Standard
    5 pages
    French language
    sale 15% off
ISO
ISO 17786:2015(Main)
Dimethyl ether (DME) for fuels — Determination of high temperature (105°C) evaporation residues — Mass analysis method

ISO 17786:2015 specifies a procedure of test for high temperature (105 °C) evaporation residue in DME used as fuel by the mass analysis method. This procedure is applicable to determine the amount of high temperature (105 °C) evaporation residue up to the value specified in ISO 16861. Several tests can be applied to determine amount of evaporation residue in liquefied products. Among them, this International Standard specifies the method that has detection limit sufficient for a DME specification in ISO 16861, using less resource compared to other methods. When more precise quantitative test is required, use of ISO 13757 instead of this International Standard is recommended. Because of the procedure applied, the evaporation residue which has a boiling point lower than 105 °C will not be determined. NOTE The precision of this method has been studied for a limited set of samples and content levels by a limited amount of labs. It allows establishment of a quality specification of DME but cannot be considered as a full precision determination in line with the usual statistical methodology as in ISO 4259.

  • Standard
    8 pages
    English language
    sale 15% off
  • Standard
    8 pages
    French language
    sale 15% off
ISO
ISO 17197:2014(Main)
Dimethyl ether (DME) for fuels — Determination of water content — Karl Fischer titration method

ISO 17197:2014 specifies a procedure of test for the amount of water content in DME used as fuel by the Karl Fischer titration method. This procedure is applicable to determine the amount of water up to the value specified in ISO 16861. This test method is intended for use with commercially available coulometric (or volumetric) Karl Fischer reagents and for the determination of water in DME additives, lube oils, base oils, automatic transmission fluids, hydrocarbon solvents, and other petroleum products. By proper choice of the sample size, this test method can be used to determine water from mg/kg (ppm) to percent level concentrations. NOTE The precision of this method has been studied for a limited set of samples and content levels by a limited amount of labs. It allows establishment of a quality specification of DME but cannot be considered as a full precision determination in line with the usual statistical methodology as in ISO 4259.

  • Standard
    10 pages
    English language
    sale 15% off
  • Standard
    10 pages
    English language
    sale 15% off
  • Standard
    10 pages
    French language
    sale 15% off
  • Standard
    10 pages
    French language
    sale 15% off
ISO
ISO 17198:2014(Main)
Dimethyl ether (DME) for fuels — Determination of total sulfur, ultraviolet fluorescence method

ISO 17198:2014 specifies a procedure of test for the sulfur content in dimethyl ether (DME) used as fuel by the ultraviolet (UV) fluorescence method. This procedure is applicable to determine the amount of total sulfur up to the value specified in ISO 16861. This test method will not measure sulfur that is not volatile under the practical conditions of the test, namely room temperature and atmospheric pressure. NOTE The precision of this method has been studied for a limited set of samples and content levels by a limited amount of labs. It allows establishment of a quality specification of DME but cannot be considered as a full precision determination in line with the usual statistical methodology as in ISO 4259.

  • Standard
    13 pages
    English language
    sale 15% off
  • Standard
    13 pages
    English language
    sale 15% off
  • Standard
    14 pages
    French language
    sale 15% off
  • Standard
    14 pages
    French language
    sale 15% off
ISO
ISO 17196:2014(Main)
Dimethyl ether (DME) for fuels — Determination of impurities — Gas chromatographic method

ISO 17196:2014 specifies a procedure of test for methanol, CO, CO2, methyl formate, ethyl methyl ether, and hydrocarbons up to C4, in DME used as fuel by the gas chromatography method. This procedure is applicable to determine the amount of methanol, CO, CO2, methyl formate, ethyl methyl ether, and hydrocarbons up to C4, up to the value specified in ISO 16861. NOTE The precision of this method has been studied for a limited set of samples and content levels by a limited number of labs. It allows establishment of a quality specification of DME but cannot be considered as a full precision determination in line with the usual statistical methodology as in ISO 4259.

  • Standard
    25 pages
    English language
    sale 15% off
  • Standard
    25 pages
    English language
    sale 15% off
  • Standard
    26 pages
    French language
    sale 15% off
ISO
ISO 4261:2013(Main)
Petroleum products — Fuels (class F) — Specifications of gas turbine fuels for industrial and marine applications

ISO 4261:2013 specifies the requirements for petroleum fuels for gas turbines (see ISO 3977) used in public utility, industrial, and marine applications. It does not cover requirements for gas turbine fuels for aviation use. ISO 4261:2013 is intended for the guidance of users such as turbine manufacturers, suppliers, and purchasers of gas turbine fuels.

  • Standard
    17 pages
    English language
    sale 15% off
  • Standard
    19 pages
    French language
    sale 15% off
ISO
ISO 8216-99:2002(Main)
Petroleum products — Fuels (class F) — Classification — Part 99: General

This part of ISO 8216 establishes a general system of classification which applies to petroleum fuels designated by the prefix letter "F". Within class F, five families (designated as categories) of products are defined according to the type of fuel and listed in decreasing order of volatility. One category, D, is defined further by subgroups on the basis of volatility and flash point, because of the safety implications of different customary titles for such fuels in different parts of the world. Subgroup L (light distillate) is a highly volatile liquid fuel with a closed-cup flash point below normal ambient temperature, and thus may require special hazard precautions not necessary for subgroups M and H. The detailed classification of a family, taking into account complementary elements according to the uses, type and properties, define particular products in each category, and are given in relevant parts of ISO 8216 as the need arises. NOTE 1 Petroleum fuels only meet the requirement of this part of ISO 8216 if these fuels, or their components, have not been used for any other purposes prior to their preparation. NOTE 2 Class F for fuels has been defined as part of the method of classification for petroleum products given in ISO 8681.

  • Standard
    6 pages
    English language
    sale 15% off
  • Standard
    3 pages
    English language
    sale 15% off
  • Standard
    3 pages
    French language
    sale 15% off