Coating powders — Part 10: Determination of deposition efficiency

This document specifies a method for determining the mass fraction in per cent (%) of a sprayed coating powder which is deposited on a test item under known spray gun and environmental conditions. The method is applicable to powders applied by corona or tribo charging and can be used to compare the deposition efficiency of different powders with the same or different gun with the same powder. This method is only used for comparison when powders or guns are evaluated consecutively, as the influence of the environment and the equipment can vary significantly with time and location.

Poudres pour revêtement — Partie 10: Détermination du rendement d'application

Le présent document spécifie une méthode pour la détermination de la fraction massique en pourcentage (%) d'une poudre pour revêtement pulvérisée qui est déposé sur un élément soumis à l'essai à partir d'un pistolet pulvérisateur dans des conditions environnementales connues. La méthode convient aux poudres appliquées par effet corona ou par triboélectricité et peut être utilisée pour comparer le rendement d'application de différentes poudres avec le même pistolet ou différents pistolets sur la même poudre. Cette méthode n'est utilisée qu'à des fins de comparaison lorsque les poudres ou les pistolets sont évalués consécutivement, car l'influence de l'environnement et du matériel peut varier sensiblement avec le temps et en fonction de l'emplacement.

General Information

Status
Published
Publication Date
22-Jun-2021
Current Stage
6060 - International Standard published
Start Date
23-Jun-2021
Due Date
02-Mar-2023
Completion Date
23-Jun-2021
Ref Project

Relations

Buy Standard

Standard
ISO 8130-10:2021 - Coating powders
English language
5 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 8130-10:2021 - Poudres pour revêtement
French language
5 pages
sale 15% off
Preview
sale 15% off
Preview
Draft
ISO/PRF 8130-10:Version 01-maj-2021 - Coating powders
English language
5 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 8130-10
Second edition
2021-06
Coating powders —
Part 10:
Determination of deposition efficiency
Poudres pour revêtement —
Partie 10: Détermination du rendement d'application
Reference number
ISO 8130-10:2021(E)
©
ISO 2021

---------------------- Page: 1 ----------------------
ISO 8130-10:2021(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2021
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2021 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 8130-10:2021(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 1
5 Apparatus . 2
6 Sampling . 2
7 Procedure. 3
8 Expression of results . 4
9 Precision . 4
10 Test report . 4
© ISO 2021 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 8130-10:2021(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www .iso .org/
iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 35, Paints and varnishes, Subcommittee
SC 9, General test methods for paints and vanishes, in collaboration with the European Committee for
Standardization (CEN) Technical Committee CEN/TC 139, Paints and varnishes, in accordance with the
Agreement on technical cooperation between ISO and CEN (Vienna Agreement).
This second edition cancels and replaces the first edition (ISO 8130-10:1998), which has been technically
revised. The main changes compared to the previous edition are as follows:
— the test report has been modified;
— the precision data have been deleted;
— the text has been editorially revised and the normative references have been updated.
A list of all parts in the ISO 8130 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/ members .html
iv © ISO 2021 – All rights reserved

---------------------- Page: 4 ----------------------
INTERNATIONAL STANDARD ISO 8130-10:2021(E)
Coating powders —
Part 10:
Determination of deposition efficiency
1 Scope
This document specifies a method for determining the mass fraction in per cent (%) of a sprayed coating
powder which is deposited on a test item under known spray gun and environmental conditions.
The method is applicable to powders applied by corona or tribo charging and can be used to compare
the deposition efficiency of different powders with the same or different gun with the same powder.
This method is only used for comparison when powders or guns are evaluated consecutively, as the
influence of the environment and the equipment can vary significantly with time and location.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 8130-14, Coating powders — Part 14: Vocabulary
ISO 15528, Paints, varnishes and raw materials for paints and varnishes — Sampling
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 8130-14
...

NORME ISO
INTERNATIONALE 8130-10
Deuxième édition
2021-06
Poudres pour revêtement —
Partie 10:
Détermination du rendement
d'application
Coating powders —
Part 10: Determination of deposition efficiency
Numéro de référence
ISO 8130-10:2021(F)
©
ISO 2021

---------------------- Page: 1 ----------------------
ISO 8130-10:2021(F)

DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2021
Tous droits réservés. Sauf prescription différente ou nécessité dans le contexte de sa mise en œuvre, aucune partie de cette
publication ne peut être reproduite ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique,
y compris la photocopie, ou la diffusion sur l’internet ou sur un intranet, sans autorisation écrite préalable. Une autorisation peut
être demandée à l’ISO à l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Case postale 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Genève
Tél.: +41 22 749 01 11
E-mail: copyright@iso.org
Web: www.iso.org
Publié en Suisse
ii © ISO 2021 – Tous droits réservés

---------------------- Page: 2 ----------------------
ISO 8130-10:2021(F)

Sommaire Page
Avant-propos .iv
1 Domaine d'application . 1
2 Références normatives . 1
3 Termes et définitions . 1
4 Principe . 1
5 Appareillage . 2
6 Échantillonnage . 2
7 Mode opératoire. 3
8 Expression des résultats. 4
9 Fidélité . 4
10 Rapport d'essai . 4
© ISO 2021 – Tous droits réservés iii

---------------------- Page: 3 ----------------------
ISO 8130-10:2021(F)

Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes
nationaux de normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est
en général confiée aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude
a le droit de faire partie du comité technique créé à cet effet. Les organisations internationales,
gouvernementales et non gouvernementales, en liaison avec l'ISO participent également aux travaux.
L'ISO collabore étroitement avec la Commission électrotechnique internationale (IEC) en ce qui
concerne la normalisation électrotechnique.
Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont
décrites dans les Directives ISO/IEC, Partie 1. Il convient, en particulier de prendre note des différents
critères d'approbation requis pour les différents types de documents ISO. Le présent document a été
rédigé conformément aux règles de rédaction données dans les Directives ISO/IEC, Partie 2 (voir www
.iso .org/ directives).
L'attention est attirée sur le fait que certains des éléments du présent document peuvent faire l'objet de
droits de propriété intellectuelle ou de droits analogues. L'ISO ne saurait être tenue pour responsable
de ne pas avoir identifié de tels droits de propriété et averti de leur existence. Les détails concernant
les références aux droits de propriété intellectuelle ou autres droits analogues identifiés lors de
l'élaboration du document sont indiqués dans l'Introduction et/ou dans la liste des déclarations de
brevets reçues par l'ISO (voir www .iso .org/ brevets).
Les appellations commerciales éventuellement mentionnées dans le présent document sont données
pour information, par souci de commodité, à l'intention des utilisateurs et ne sauraient constituer un
engagement.
Pour une explication de la nature volontaire des normes, la signification des termes et expressions
spécifiques de l'ISO liés à l'évaluation de la conformité, ou pour toute information au sujet de l'adhésion
de l'ISO aux principes de l'Organisation mondiale du commerce (OMC) concernant les obstacles
techniques au commerce (OTC), voir www .iso .org/ avant -propos.
Le présent document a été élaboré par le comité technique ISO/TC 35, Peintures et vernis, sous-
comité SC 9, Méthodes générales d'essais des peintures et vernis, en collaboration avec le comité technique
CEN/TC 139, Peintures et vernis, du Comité européen de normalisation (CEN), conformément à l'Accord
de coopération technique entre l'ISO et le CEN (Accord de Vienne).
Cette deuxième édition annule et remplace la première édition (ISO 8130-10:1998), qui a fait l'objet
d'une révision technique. Les principales modifications par rapport à l'édition précédente sont les
suivantes:
— le rapport d'essai a été modifié;
— les données de fidélité ont été supprimées;
— le texte a fait l'objet d'une révision éditoriale et les références normatives ont été mises à jour.
Une liste de toutes les parties de la série ISO 8130 est disponible sur le site de l'ISO.
Il convient que l'utilisateur adresse tout retour d'information ou toute question concernant le présent
document à l'organisme national de normalisation de son pays. Une liste exhaustive desdits organismes
se trouve à l'adresse www .iso .org/ fr/ members .html.
iv © ISO 2021 – Tous droits réservés

---------------------- Page: 4 ----------------------
NORME INTERNATIONALE ISO 8130-10:2021(F)
Poudres pour revêtement —
Partie 10:
Détermination du rendement d'application
1 Domaine d'application
Le présent document spécifie une méthode pour la détermination de la fraction massique en
pourcentage (%) d'une poudre pour revêtement pulvérisée qui est déposé sur un élément soumis à
l'essai à partir d'un pistolet pulvérisateur dans des conditions environnementales connues.
La méthode convient aux poudres appliquées par effet corona ou par triboélectricité et peut être utilisée
pour comparer le rendement d'application de différentes poudres avec le même pistolet ou différents
pistolets sur la même poudre.
Cette méthode n'est utilisée qu'à des fins de comparaison lorsque les poudres ou les pistolets sont
évalués consécutivement, car l'influence de l'environnement et du matériel peut varier sensiblement
avec le temps et en fonction de l'emplacement.
2 Références normatives
Les documents suivants sont cités dans le texte de sorte qu’ils constituent, pour tout ou partie de leur
contenu, des exigences du présent document. Pour les références datées, seule l’édition citée s’applique.
Pour les références non datées, la dernière édition du document de référence s'applique (y compris les
éventuels amendements).
ISO 8130-14, Poudres pour revêtement — Partie 14: Vocabulaire
ISO 15528, Peintures, vernis et matières premières pour peintures et vernis — Échantillonnage
3 Termes et définitions
Pour les besoins du présent document, les termes et définitions donnés dans l'ISO 8130-14 ainsi que les
suivants s'appliquent.
L'ISO et l'IEC tiennent à jour des bases de données terminologiques destinées à être utilisées en
normalisation,
...

INTERNATIONAL ISO
STANDARD 8130-10
Second edition
Coating powders —
Part 10:
Determination of deposition efficiency
Poudres pour revêtement —
Partie 10: Détermination du rendement d'application
PROOF/ÉPREUVE
Reference number
ISO 8130-10:2021(E)
©
ISO 2021

---------------------- Page: 1 ----------------------
ISO 8130-10:2021(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2021
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii PROOF/ÉPREUVE © ISO 2021 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 8130-10:2021(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 1
5 Apparatus . 2
6 Sampling . 2
7 Procedure. 3
8 Expression of results . 4
9 Precision . 4
10 Test report . 4
© ISO 2021 – All rights reserved PROOF/ÉPREUVE iii

---------------------- Page: 3 ----------------------
ISO 8130-10:2021(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www .iso .org/
iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 35, Paints and varnishes, Subcommittee
SC 9, General test methods for paints and vanishes, in collaboration with the European Committee for
Standardization (CEN) Technical Committee CEN/TC 139, Paints and varnishes, in accordance with the
Agreement on technical cooperation between ISO and CEN (Vienna Agreement).
This second edition cancels and replaces the first edition (ISO 8130-10:1998), which has been technically
revised. The main changes compared to the previous edition are as follows:
— the test report has been modified;
— the precision data have been deleted;
— the text has been editorially revised and the normative references have been updated.
A list of all parts in the ISO 8130 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/ members .html
iv PROOF/ÉPREUVE © ISO 2021 – All rights reserved

---------------------- Page: 4 ----------------------
INTERNATIONAL STANDARD ISO 8130-10:2021(E)
Coating powders —
Part 10:
Determination of deposition efficiency
1 Scope
This document specifies a method for determining the mass fraction in per cent (%) of a sprayed coating
powder which is deposited on a test item under known spray gun and environmental conditions.
The method is applicable to powders applied by corona or tribo charging and can be used to compare
the deposition efficiency of different powders with the same or different gun with the same powder.
This method is only used for comparison when powders or guns are evaluated consecutively, as the
influence of the environment and the equipment can vary significantly with time and location.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 8130-14, Coating powders — Part 14: Vocabulary
ISO 15528, Paints, varnishes and raw materials for paints and varnishes — Sampling
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 8130-14 and the followin
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.