ISO 3819:2015

Laboratory glassware — Beakers

ISO 3819:2015 specifies requirements for an internationally acceptable series of glass beakers for laboratory use.

Verrerie de laboratoire — Béchers

ISO 3819:2015 spécifie des exigences relatives à une série de béchers en verre destinés à être utilisés en laboratoire, acceptable sur le plan international.

General Information

• Status: Published
• Publication Date: 09-Dec-2015
• ICS: 17.060 - Measurement of volume, mass, density, viscosity
• Technical Committee: ISO/TC 48 - Laboratory equipment
• Drafting Committee: ISO/TC 48 - Laboratory equipment
• Current Stage: 9093 - International Standard confirmed
• Completion Date: 05-Mar-2021

Relations

• Consolidates: ISO 8330:2007 - Rubber and plastics hoses and hose assemblies — Vocabulary
• Effective Date: 06-Jun-2022
• Revises: ISO 3819:1985 - Laboratory glassware — Beakers
• Effective Date: 04-May-2013

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 3819
Second edition
2015-12-15
Laboratory glassware — Beakers
Verrerie de laboratoire — Béchers
Reference number
ISO 3819:2015(E)
©
ISO 2015

---------------------- Page: 1 ----------------------
ISO 3819:2015(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2015, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. [phone]
Fax [phone]
[e-mail]
www.iso.org
ii © ISO 2015 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 3819:2015(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Types of beakers . 1
4 Series of beakers . 1
5 Capacity . 1
6 Material . 2
7 Dimensions . 2
7.1 General . 2
7.2 Radius at base . 2
7.3 Wall thickness . 2
8 Details of construction . 3
8.1 Base . 3
8.2 Upper edge . 3
8.3 Spout . 3
8.4 Scale . 4
8.5 Thermal shock resistance . 4
9 Marking . 4
© ISO 2015 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 3819:2015(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical
Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information.
The committee responsible for this document is ISO/TC 48, Labo
...

DRAFT INTERNATIONAL STANDARD
ISO/DIS 3819
ISO/TC 48 Secretariat: DIN
Voting begins on: Voting terminates on:
2013-10-31 2014-03-31
Laboratory glassware — Beakers
Verrerie de laboratoire — Béchers
[Revision of first edition (ISO 3819:1985)]
ICS: 17.060
ISO/CEN PARALLEL PROCESSING
This draft has been developed within the International Organization for
Standardization (ISO), and processed under the ISO lead mode of collaboration
as defined in the Vienna Agreement.
This draft is hereby submitted to the ISO member bodies and to the CEN member
bodies for a parallel five month enquiry.
Should this draft be accepted, a final draft, established on the basis of comments
received, will be submitted to a parallel two-month approval vote in ISO and
THIS DOCUMENT IS A DRAFT CIRCULATED
formal vote in CEN.
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
To expedite distribution, this document is circulated as received from the
IN ADDITION TO THEIR EVALUATION AS
committee secretariat. ISO Central Secretariat work of editing and text
BEING ACCEPTABLE FOR INDUSTRIAL,
composition will be undertaken at publication stage.
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 3819:2013(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
©
PROVIDE SUPPORTING DOCUMENTATION. ISO 2013

---------------------- Page: 1 ----------------------
ISO/DIS 3819:2013(E)

Copyright notice
This ISO document is a Draft International Standard and is copyright-protected by ISO. Except as
permitted under the applicable laws of the user’s country, neither this ISO draft nor any extract
from it may be reproduced, stored in a retrieval system or transmitted in any form or by any means,
electronic, photocopying, recording or otherwise, without prior written permission being secured.
Requests for permission to reproduce should be addressed to either ISO at the address below or ISO’s
member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Reproduction may be subject to royalty payments or a licensing agreement.
Violators may be prosecuted.
ii © ISO 2013 – All rights reserved

---------------------- Page: 2 ----------------------
ISO/DIS 3819
Contents Page
Foreword . iv
1 Scope . 1
2 Normative references . 1
3 Types of beakers . 1
4 Series of beakers . 1
5 Capacity . 1
6 Material . 2
7 Dimensions . 2
7.1 General . 2
7.2 Radius at base . 2
7.3 Wall thickness . 2
8 Details of construction . 4
8.1 Base . 4
8.2 Upper edge . 4
8.3 Spout . 4
8.4 Scale . 4
8.5 Thermal shock resistance . 4
9 Marking . 4

© ISO 2013 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO/DIS 3819
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all s
...

NORME ISO
INTERNATIONALE 3819
Deuxième édition
2015-12-15
Verrerie de laboratoire — Béchers
Laboratory glassware — Beakers
Numéro de référence
ISO 3819:2015(F)
©
ISO 2015

---------------------- Page: 1 ----------------------
ISO 3819:2015(F)

DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2015, Publié en Suisse
Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite ni utilisée
sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie, l’affichage sur
l’internet ou sur un Intranet, sans autorisation écrite préalable. Les demandes d’autorisation peuvent être adressées à l’ISO à
l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. [phone]
Fax [phone]
[e-mail]
www.iso.org
ii © ISO 2015 – Tous droits réservés

---------------------- Page: 2 ----------------------
ISO 3819:2015(F)

Sommaire Page
Avant-propos .iv
1 Domaine d’application . 1
2 Références normatives . 1
3 Types de bécher. 1
4 Séries de béchers . 1
5 Capacité . 1
6 Matériau . 2
7 Dimensions . 2
7.1 Généralités . 2
7.2 Rayon de raccordement à la base. 2
7.3 Épaisseur de paroi . 2
8 Détails de la conception . 4
8.1 Fond . 4
8.2 Partie supérieure . 4
8.3 Bec verseur . 4
8.4 Échelle . 4
8.5 Résistance au choc thermique . 4
9 Marquage . 4
© ISO 2015 – Tous droits réservés iii

---------------------- Page: 3 ----------------------
ISO 3819:2015(F)

Avant-propos
L’ISO (Organisation internationale de normalisation) est une fédération mondiale d’organismes
nationaux de normalisation (comités membres de l’ISO). L’élaboration des Normes internationales est
en général confiée aux comités techniques de l’ISO. Chaque comité membre intéressé par une étude
a le droit de faire partie du comité technique créé à cet effet. Les organisations internationales,
gouvernementales et non gouvernementales, en liaison avec l’ISO participent également aux travaux.
L’ISO collabore étroitement avec la Commission électrotechnique internationale (IEC) en ce qui
concerne la normalisation électrotechnique.
Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont
décrites dans les Directives ISO/IEC, Partie 1. Il convient, en particulier de prendre note des différents
critères d’approbation requis pour les différents types de documents ISO. Le présent document a été
rédigé conformément aux règles de rédaction données dans les Directives ISO/IEC, Partie 2 (voir www.
iso.org/directives).
L’attention est appelée sur le fait que certains des éléments du présent document peuvent faire l’objet de
droits de propriété intellectuelle ou de droits analogues. L’ISO ne saurait être tenue pour responsable
de ne pas avoir identifié de tels droits de propriété et averti de leur existence. Les détails concernant
les références aux droits de propriété intellectuelle ou autres droits analogues identifiés lors de
l’élaboration du document sont indiqués dans l’Introduction et/ou dans la liste des déclarations de
brevets reçues par l’ISO (voir www.iso.org/brevets).
Les appellations commerciales éventuellement mentionnées dans le présent document sont données
pour information, par souci de commodité, à l’intention des utilisateurs et ne sauraient constituer
un engagement.
Pour une explication de la signification des termes et expressions spécifiques de l’ISO liés à
l’évaluation de la conformité, ou pour toute information au sujet de l’adhésion de l’ISO aux principes
de l’OMC concernant les obstacles techniques au commerce (OTC), voir le lien suivant: Avant-propos —
Informations supplémentaires.
Le comité chargé de l’élaboration du présent document est l’ISO/TC 48, Équipement de laboratoire, et
par le comité technique CEN/TC 332, Équipement de laboratoire, en collaboration.
Cette deuxième édition annule et remplace la première édition (ISO 3819:1985), qui a fait l’objet d’une
révision technique en vue d’apporter les modifications
...