EN ISO 13807:2022

Vitreous and porcelain enamels - Determination of crack formation temperature in the thermal shock testing of enamels for the chemical industry (ISO 13807:2022)

This document specifies a test method for the determination of the crack formation temperature of enamels for the chemical industry by subjecting enamelled steel specimens to thermal shock using cold water.
The value of the crack formation temperature measured according to this test method does not apply to the finished component (see Annex A). It is a parameter of vitreous and porcelain enamels for comparing the relative quality of different enamel formulations.

Emails und Emaillierungen - Bestimmung der Rissbildungstemperatur von Chemie-Emails beim Abschreckversuch (ISO 13807:2022)

Dieses Dokument legt ein Prüfverfahren zur Bestimmung der Rissbildungstemperatur von Chemie-Emails durch Abschrecken emaillierter Stahlproben mit kaltem Wasser fest.
Der nach diesem Prüfverfahren gemessene Wert der Rissbildungstemperatur gilt nicht für das fertige Bauteil (siehe Anhang A). Er ist eine Kenngröße von Emails und Emaillierungen für den Vergleich der relativen Qualität verschiedener Emailrezepturen.

Émaux vitrifiés - Détermination de la température de fissuration par choc thermique d'émaux pour l'industrie chimique (ISO 13807:2022)

Le présent document spécifie une méthode d'essai pour la détermination de la température de fissuration des émaux pour l'industrie chimique en soumettant la surface d'éprouvettes d'acier émaillé à un choc thermique en utilisant de l'eau froide.
La valeur de la température de fissuration mesurée conformément à cette méthode d'essai ne s'applique pas au composant fini (voir Annexe A). Il s'agit d'un paramètre relatif aux émaux soumis à essai utilisé comme valeur comparative par rapport aux autres qualités d'émaux.

Steklasti in porcelanski emajli - Ugotavljanje temperature pokanja emajlov za kemično industrijo zaradi izpostavljenosti toplotnemu šoku (ISO 13807:2022)

General Information

• Status: Published
• Publication Date: 01-Nov-2022
• ICS: 25.220.50 - Enamels
• Technical Committee: CEN/TC 262 - Metallic and other inorganic coatings
• Drafting Committee: CEN/TC 262 - Metallic and other inorganic coatings
• Current Stage: 6060 - Definitive text made available (DAV) - Publishing
• Start Date: 02-Nov-2022
• Completion Date: 02-Nov-2022
• Ref Project: SIST EN ISO 13807:2022 - Vitreous and porcelain enamels - Determination of crack formation temperature in the thermal shock testing of enamels for the chemical industry (ISO 13807:2022)

Relations

• Replaces: EN ISO 13807:2009 - Vitreous and porcelain enamels - Determination of crack formation temperature in the thermal shock testing of enamels for the chemical industry (ISO 13807:1999, including Cor 1:2000)
• Effective Date: 13-Oct-2021

Standards Content (Sample)

SLOVENSKI STANDARD
01-december-2022
Nadomešča:
SIST EN ISO 13807:2009
Steklasti in porcelanski emajli - Ugotavljanje temperature pokanja emajlov za
kemično industrijo zaradi izpostavljenosti toplotnemu šoku (ISO 13807:2022)
Vitreous and porcelain enamels - Determination of crack formation temperature in the
thermal shock testing of enamels for the chemical industry (ISO 13807:2022)
Emails und Emaillierungen - Bestimmung der Rissbildungstemperatur von Chemie-
Emails beim Abschreckversuch (ISO 13807:2022)
Émaux vitrifiés - Détermination de la température de fissuration par choc thermique
d'émaux pour l'industrie chimique (ISO 13807:2022)
Ta slovenski standard je istoveten z: EN ISO 13807:2022
ICS:
25.220.50 Emajlne prevleke Enamels
71.020 Proizvodnja v kemijski Production in the chemical
industriji industry
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 13807
EUROPEAN STANDARD
NORME EUROPÉENNE
November 2022
EUROPÄISCHE NORM
ICS 25.220.50 Supersedes EN ISO 13807:2009
English Version
Vitreous and porcelain enamels - Determination of crack
formation temperature in the thermal shock testing of
enamels for the chemical industry (ISO 13807:2022)
Émaux vitrifiés - Détermination de la température de Emails und Emaillierungen - Bestimmung der
fissuration par choc thermique d'émaux pour Rissbildungstemperatur von Chemie-Emails beim
l'industrie chimique (ISO 13807:2022) Abschreckversuch (ISO 13807:2022)
This European Standard was approved by CEN on 22 October 2022.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 13807:2022 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
This document (EN ISO 13807:2022) has been prepared by Technical Committee ISO/TC 107 "Metallic
and other inorganic coatings" in collaboration with Technical Committee CEN/TC 262 “Metallic and
other inorganic coatings, including for corrosion protection and corrosion testing of metals and alloys”
the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by May 2023, and conflicting national standards shall be
withdrawn at the latest by May 2023.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 13807:2009.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 13807:2022 has been approved by CEN as EN ISO 13807:2022 without any modification.

INTERNATIONAL ISO
STANDARD 13807
Second edition
2022-10
Vitreous and porcelain enamels —
Determination of crack formation
temperature in the thermal shock
testing of enamels for the chemical
industry
Émaux vitrifiés — Détermination de la température de fissuration par
choc thermique d'émaux pour l'industrie chimique
Reference number
ISO 13807:2022(E)
ISO 13807:2022(E)
© ISO 2022
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Email: [e-mail]
Website: www.iso.org
Published in Switzerland
ii
ISO 13807:2022(E)
Contents Page
Foreword .iv
1 S c op e . 1
2 Nor m at i ve r ef er enc e s . 1
3 Terms and definitions . 1
4 D e sig n at ion . 1
5 P r i nc iple . 2
6 A pp a r at u s . 2
7 S p e c i men s. 2
7.1 S hape and preparation of specimens . 2
7.2 N umber of specimens . 3
8 P r o c e du re .3
9 E xpression of results . 4
10 Te s t r ep or t . 4
Annex A (informative) Explanatory notes . 5
iii
ISO 13807:2022(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO’s adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 107, Metallic and other inorganic coatings,
in collaboration with the European Committee for Standardization (CEN) Technical Committee CEN/
TC 262, Metallic and other inorganic coatings, including for corrosion protection and corrosion testing of
metals and alloys, in accordance with the Agreement on technical cooperation between ISO and CEN
(Vienna Agreement).
This second edition cancels and replaces the first edition (ISO 13807:1999), which has been technically
revised. It also incorporates the Technical Corrigendum ISO 13807:1999/Cor 1:2000.
The main changes are as follows:
— the normative references have been updated;
— the method for measuring coating thickness has been updated;
— the thickness requirements for the vitreous enamel coating have been updated;
— the specimen heating temperature requirements have been updated.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iv
INTERNATIONAL STANDARD ISO 13807:2022(E)
Vitreous and porcelain enamels — Determination of crack
formation temperature in the thermal shock testing of
enamels for the chemical industry
1 S cope
This document specifies a test method for the determination of the crack formation temperature of
enamels for the chemical industry by subjecting enamelled steel specimens to thermal shock using cold
water.
The value of the crack formation temperature measured according to this test method does not apply to
the finished component (see Annex A). It is a parameter of vitreous and porcelain enamels for comparing
the relative quality of different enamel formulations.
2 Normat ive references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 2178, Non-magnetic coatings on magnetic substrates — Measurement of coating thickness — Magnetic
method
ISO 2746, Vitreous and porcelain enamels — High voltage test
ISO 3819, Laboratory glassware — Beakers
ISO 19496-1, Vitreous and porcelain enamels — Terminology — Part 1: Terms and definitions
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 19496-1 and the following
apply.
ISO and IEC maintain terminology databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https:// www .iso .org/ obp
— IEC Electropedia: available at https:// www .electropedia .org/
3.1
crack formation temperature
thermal shock temperature (3.2) at which the first damage to the enamel occurs in the form of cracks
and/or chipping
3.2
thermal shock temperature
temperature of the specimen immediately before quenching with cold water
4 Designation
The test method for the determination
...