ISO 18913:2003
(Main)Imaging materials — Permanence — Vocabulary
Imaging materials — Permanence — Vocabulary
ISO 18913:2003 establishes a vocabulary of terms and definitions used in respect of the permanence of imaging materials and in standards related to permanence. These terms and definitions are generic and are applicable to the entire imaging industry.
Matériaux pour image — Permanence — Vocabulaire
Upodobitveni materiali - Obstojnost - Pojmovnik
Ta mednarodni standard vzpostavlja pojmovnik izrazov in opredelitev, ki se uporabljajo v zvezi z obstojnostjo materialov za upodabljanje in v standardih, povezanih z obstojnostjo. Ti izrazi in opredelitve so generični in veljajo za celotno upodobitveno panogo.
Za izraze in opredelitve, specifične za določeno aplikacijo, si oglejte panožne standarde.
General Information
Relations
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 18913
First edition
2003-05-15
Imaging materials — Permanence —
Vocabulary
Matériaux pour image — Permanence — Vocabulaire
Reference number
ISO 18913:2003(E)
©
ISO 2003
---------------------- Page: 1 ----------------------
ISO 18913:2003(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2003
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2003 — All rights reserved
---------------------- Page: 2 ----------------------
ISO 18913:2003(E)
Contents Page
Foreword. iv
Introduction . v
1 Scope. 1
2 Normative references. 1
3 Terms and definitions. 1
Annex A (informative) Numbering system for related International Standards. 15
Bibliography . 17
© ISO 2003 — All rights reserved iii
---------------------- Page: 3 ----------------------
ISO 18913:2003(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 18913 was prepared by Technical Committee ISO/TC 42, Photography.
iv © ISO 2003 — All rights reserved
---------------------- Page: 4 ----------------------
ISO 18913:2003(E)
Introduction
This International Standard is one of a series dealing with the physical properties and stability of imaging
materials.
In order to facilitate identification of these International Standards, they are to be assigned new numbers
within the block from 18900 to 18999 (see Annex A).
© ISO 2003 — All rights reserved v
---------------------- Page: 5 ----------------------
INTERNATIONAL STANDARD ISO 18913:2003(E)
Imaging materials — Permanence — Vocabulary
1 Scope
This International Standard establishes a vocabulary of terms and definitions used in respect of the
permanence of imaging materials and in standards related to permanence. These terms and definitions are
generic and are applicable to the entire imaging industry. For terms and definitions specific to particular
applications, refer to industry standards.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 5-3, Photography — Density measurements — Part 3: Spectral conditions
ISO 18906, Imaging materials — Photographic films — Specifications for safety film
ISO 14644-1, Cleanrooms and associated controlled environments — Part 1: Classification of air cleanliness
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1
accuracy
closeness of the agreement between the result of a measurement and a true value of the measurement
NOTE 1 Accuracy is a qualitative concept.
NOTE 2 The term precision (3.85) should not be used for accuracy.
3.2
album
binder or book structure having front and back covers (usually opaque and rigid) in which pages are bound
along one edge either by plastic straps, gluing, sewing, metal posts or rings
3.3
anti-blocking agent
component of a material that provides microscopic bumps on the surface in order to lower contact area,
reduce the coefficient of friction, and minimize ferrotyping and the occurrence of Newton's rings (3.74)
EXAMPLE Talc, silicates or matte beads.
© ISO 2003 — All rights reserved 1
---------------------- Page: 6 ----------------------
ISO 18913:2003(E)
3.4
aperture
window
opening in the flange (3.42) that is used to facilitate threading of magnetic tape on the hub (3.50) and
inspection of the wind (3.114)
3.5
aperture card
card of standard dimensions with one or more openings into which a microfilm frame or frames can be
mounted or inserted
3.6
. . . . .
archival medium (deprecated)
recording material that can be expected to retain information (3.56) forever, so that such information can be
retrieved without significant loss when properly stored
NOTE However, as no such material exists, this is a deprecated term and as such is not to be used in International
Standards or system specifications.
3.7
Arrhenius plot
plot of the logarithm of the time for a given change in a characteristic proportional to the reaction rate (dye loss,
tensile strength change, D yellowing, etc.) versus the reciprocal of the temperature expressed in kelvins
min
NOTE The Arrhenius plot can be used to predict behaviour at a temperature lower than that at which a test is run.
3.8
base
support in a recording material on which the emulsion layers or magnetic layer (and, if necessary, the back
layer) are coated
3.8.1
cellulose-acetate base
base for recording materials composed mainly of cellulose esters of acetic acid
3.8.2
cellulose-ester base
base for recording materials composed mainly of cellulose esters of acetic, propionic, or butyric acid, or
mixtures thereof
3.8.3
polyester base
base for recording materials composed mainly of a polymer of ethylene glycol and terephthalic acid (also
referred to as polyethylene terephthalate) or a polymer of ethylene glycol and 2,6-naphthalene-dicarboxylic
acid (also referred to as polyethylene naphthalate)
3.8.4
poly(ethylene terephthalate) base
polyester base for recording materials composed mainly of a polymer of ethylene glycol and terephthalic acid
3.9
blister
localized delamination that resembles a bubble
3.10
blocking
sticking together of similar or dissimilar materials in physical contact
cf. anti-blocking agent (3.3)
2 © ISO 2003 — All rights reserved
---------------------- Page: 7 ----------------------
ISO 18913:2003(E)
3.11
brittleness
property of a material that causes it to crack or break when bent or flexed
3.12
can
metal or plastic container (3.20) for a roll of recording material, such as photographic film (3.79) or
magnetic tape
3.13
carrier
medium upon which information (3.56) is recorded
cf. medium (3.68)
3.14
carton
box
outer container (3.20) that can hold one or more individual units and which may be a fabrication of paper,
card stock or plastic
3.15
cartridge
housing for a roll of recording material, such as photographic film (3.79) or magnetic tape, wound on a single
hub (3.50) or reel (3.89)
cf. cassette (3.16)
3.16
cassette
housing for a roll of recording material, such as photographic film (3.79) or magnetic tape, whose ends are
attached to two hub(s) (3.50) or reel(s) (3.89)
cf. cartridge (3.15)
3.17
class 100 000 clean room
controlled environment in which the level of airborne contaminates meets the requirements of ISO 14644-1
3.18
compact disc
CD
optical disc (3.76) format in which the information (3.56) layer is located at one surface of a substrate and
the data can be read by an optical beam
NOTE Described in IEC 60908.
3.18.1
CD-ROM
read-only-medium compact disc
optical disc (3.76) to which information (3.76) is transferred during manufacture to certain areas in the
compact disc format and can be read many times
NOTE Described in ISO/IEC 10149.
3.18.2
CD-R
recordable compact disc
recordable optical disc (3.76) in which information (3.56) can be recorded (once) to certain areas in the
compact disc format and read many times
© ISO 2003 — All rights reserved 3
---------------------- Page: 8 ----------------------
ISO 18913:2003(E)
3.18.3
CD-RW
rewritable compact disc
recordable optical disc (3.76) in which information (3.56) can be recorded to certain areas in the compact
disc format, erased and rerecorded many times, and read many times
3.19
conditioning
exposure of a specimen to air at a given relative humidity (3.52.2) and temperature until equilibrium is
reached
3.20
container
box, can or carton used for storage and shipping of recording materials
EXAMPLE The box into which a reel (3.89), cassette (3.16), cartridge (3.15) or shell (3.93) is placed.
NOTE Reels, cassettes, cartridges or shells are not containers.
3.20.1
insulated record container
storage box designed to withstand elevated temperatures and conforming to national standards and
regulations
3.21
copy
reproduction of the information (3.56) from a master
3.22
core
metal or plastic cylinder on which recording material is wound
cf. hub (3.50)
3.23
cupping
departure of film or paper from physical flatness characterized by the condition where the four corners of a
rectangular sheet turn up, but the edges do not
3.24
curl
departure of film, paper or magnetic tape from physical flatness with the tendency to curve into a cylindrical
shape
3.25
delamination
separation of a laminate into its constituent layers
3.26
optical density
density
degree of light absorption, reflection or scattering characteristics of a photographic image, expressed as the
logarithm to the base 10 of the ratio of incident radiant flux to the transmitted, reflected or scattered flux
3.26.1
printing density
optical density of a processed photographic image in which the incident radiant flux has the same spectral
energy distribution as the printer light source and the transmitted density is evaluated by a receiver having the
same spectral response as the print material
4 © ISO 2003 — All rights reserved
---------------------- Page: 9 ----------------------
ISO 18913:2003(E)
3.26.2
projection density
optical density of a processed photographic image in which the angular distributions of the incident and
transmitted radiant flux are equal and specified
3.26.3
visual density
optical density of a processed photographic image in which the incident radiant flux has a spectral energy
distribution as defined in ISO 5-3 and the transmitted or reflected radiant flux is evaluated by the human eye
or by a receiver having the same spectral response as the human eye
3.27
dew point
temperature at which moisture begins to condense on a surface, corresponding to saturation for a given
absolute humidity (3.52.1)
EXAMPLE The more humid the air, the higher the dew-point temperature.
See, also, relative humidity (3.52.2).
3.28
differential dimensional change
difference between the dimensional changes of the material in the two principal directions (length and width)
NOTE Polyester-based films frequently have maximum and minimum dimensional changes in directions other than
the length or width. These can be determined by rotating and viewing the uncoated base between a pair of crossed
polarizers. When the direction corresponding to either the maximum or minimum dimensional change is coincident with
the optical axis of one polarizer, there is minimum light transmission through the base.
3.29
digital versatile disc
DVD
optical disc (3.76) format in which one or more information (3.56) layers are located between two substrates
and the data can be read by an optical beam
NOTE Formerly called digital video disc.
3.30
dimensional change
〈processing alone〉 permanent dimensional change caused by photographic processing
NOTE This can be the conventional wet chemical processing, vapour processing or heat processing. The
dimensional change is measured after conditioning at the same relative humidity (3.52.2) and temperature as used for
the original measurement and is expressed as a percentage.
3.31
dimensional change
〈processing and ageing together〉 permanent dimensional change that occurs as a result of processing plus
ageing of the processed material
NOTE It is measured after conditioning of the processed, aged film or paper at the same relative humidity (3.52.2)
and temperature as used for the original measurement and is expressed as a percentage.
3.32
dimensional hysteresis
difference in the absolute dimensions of a specimen in equilibrium with air at a given relative humidity
(3.52.2), when conditioned from a higher relative humidity and when conditioned from a lower relative humidity
© ISO 2003 — All rights reserved 5
---------------------- Page: 10 ----------------------
ISO 18913:2003(E)
3.33
duplicate
reproduction of a master, retaining the same polarity and size
3.34
emulsion layer
image or image-forming layer of photographic film (3.79), paper and plate
3.35
encapsulation
sealing of all edges of a specimen that has been laminated on both front and back surfaces
NOTE This process is usually done by laminating with sheets whose dimensions are larger than the specimen's and
then sealing at the overlaps.
3.36
enclosure
folder, envelope, sleeve or clam shell that is intended for physical protection against mechanical damage
3.36.1
open enclosure
enclosure that is intended for physical protection against mechanical damage, but is neither light-tight nor
airtight
EXAMPLE Spool, reel (3.89), core (3.22), cassette (3.16), magazine, folder, envelope, carton, box, sleeve,
transparency mount or aperture card.
3.36.2
photographic enclosure
container (3.20) in close or direct contact with photographic plates, films or papers such as reels, cans, bags,
folders, sleeves (sheaths), jackets, envelopes, window mounts or mats, slide mounts, cartons, boxes and
aperture cards
3.36.3
protective enclosure
impermeable sealed container (3.20), which could also by necessity be opaque, used for protection from
outside factors such as reactive gases and moisture, including changes in relative humidity (3.52.2), and
from light in the case of certain kinds of products
NOTE Such enclosures can be taped cans and sealed envelopes.
3.36.4
storage enclosure
item in close or direct contact with recording material
EXAMPLE Folder, envelope, sleeve, album (3.2), mat, cartridge (3.15) or cassette (3.16).
3.37
envelope
bag
enclosure (3.36) that is sealed with adhesive, mechanically joined or heat-sealed on two-edges with a bottom
fold and one side open
3.38
extended-term storage conditions
storage conditions suitable for the preservation of recorded information (3.56) having permanent value
6 © ISO 2003 — All rights reserved
---------------------- Page: 11 ----------------------
ISO 18913:2003(E)
3.39
ferrotyping
glazing
changing of surface characteristics resulting from contact of two surfaces
3.40
fire-protective storage
facility designed to protect records against excessive temperatures, water and other fire-fighting agents, and
steam developed by insulation of safes or caused by the extinguishing of fires and collapsing structures
3.41
fire-resistant vault
fire-resistant vault as defined in appropriate national standards and regulations
3.42
flange
fixed or removable circular disc that is connected to the hub (3.50) to make a reel (3.89) for the purpose of
protecting the roll of recording materials
cf. reel (3.89)
3.43
folder
single sheet that is folded, does not have adhesive seams, and can be made from either paper or plastic
3.44
folding endurance
measure of fatigue resistance after multiple flexing
3.45
frost point
temperature to which moisture-laden air must be cooled for frost or ice formation
3.46
full reversal processing
processing of a photographic film (3.79) or paper to produce a positive image using bleach and
redevelopment
3.47
glass transition
reversible change in an amorphous polymer from, or to, a viscous or rubbery condition to, or from, a hard and
relatively brittle one
3.48
glass transition temperature
T
g
approximate mid-point of the temperature range over which glass transition takes place
NOTE 1 T can be determined readily only by observing the temperature at which a significant change takes place in a
g
specific electrical, mechanical or other physical p
...
SLOVENSKI STANDARD
SIST ISO 18913:2011
01-julij-2011
Upodobitveni materiali - Obstojnost - Pojmovnik
Imaging materials - Permanence - Vocabulary
Matériaux pour image - Permanence - Vocabulaire
Ta slovenski standard je istoveten z: ISO 18913:2003
ICS:
01.040.37 Slikovna tehnologija (Slovarji) Image technology
(Vocabularies)
37.040.01 Fotografija na splošno Photography in general
SIST ISO 18913:2011 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST ISO 18913:2011
---------------------- Page: 2 ----------------------
SIST ISO 18913:2011
INTERNATIONAL ISO
STANDARD 18913
First edition
2003-05-15
Imaging materials — Permanence —
Vocabulary
Matériaux pour image — Permanence — Vocabulaire
Reference number
ISO 18913:2003(E)
©
ISO 2003
---------------------- Page: 3 ----------------------
SIST ISO 18913:2011
ISO 18913:2003(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2003
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2003 — All rights reserved
---------------------- Page: 4 ----------------------
SIST ISO 18913:2011
ISO 18913:2003(E)
Contents Page
Foreword. iv
Introduction . v
1 Scope. 1
2 Normative references. 1
3 Terms and definitions. 1
Annex A (informative) Numbering system for related International Standards. 15
Bibliography . 17
© ISO 2003 — All rights reserved iii
---------------------- Page: 5 ----------------------
SIST ISO 18913:2011
ISO 18913:2003(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 18913 was prepared by Technical Committee ISO/TC 42, Photography.
iv © ISO 2003 — All rights reserved
---------------------- Page: 6 ----------------------
SIST ISO 18913:2011
ISO 18913:2003(E)
Introduction
This International Standard is one of a series dealing with the physical properties and stability of imaging
materials.
In order to facilitate identification of these International Standards, they are to be assigned new numbers
within the block from 18900 to 18999 (see Annex A).
© ISO 2003 — All rights reserved v
---------------------- Page: 7 ----------------------
SIST ISO 18913:2011
---------------------- Page: 8 ----------------------
SIST ISO 18913:2011
INTERNATIONAL STANDARD ISO 18913:2003(E)
Imaging materials — Permanence — Vocabulary
1 Scope
This International Standard establishes a vocabulary of terms and definitions used in respect of the
permanence of imaging materials and in standards related to permanence. These terms and definitions are
generic and are applicable to the entire imaging industry. For terms and definitions specific to particular
applications, refer to industry standards.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 5-3, Photography — Density measurements — Part 3: Spectral conditions
ISO 18906, Imaging materials — Photographic films — Specifications for safety film
ISO 14644-1, Cleanrooms and associated controlled environments — Part 1: Classification of air cleanliness
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1
accuracy
closeness of the agreement between the result of a measurement and a true value of the measurement
NOTE 1 Accuracy is a qualitative concept.
NOTE 2 The term precision (3.85) should not be used for accuracy.
3.2
album
binder or book structure having front and back covers (usually opaque and rigid) in which pages are bound
along one edge either by plastic straps, gluing, sewing, metal posts or rings
3.3
anti-blocking agent
component of a material that provides microscopic bumps on the surface in order to lower contact area,
reduce the coefficient of friction, and minimize ferrotyping and the occurrence of Newton's rings (3.74)
EXAMPLE Talc, silicates or matte beads.
© ISO 2003 — All rights reserved 1
---------------------- Page: 9 ----------------------
SIST ISO 18913:2011
ISO 18913:2003(E)
3.4
aperture
window
opening in the flange (3.42) that is used to facilitate threading of magnetic tape on the hub (3.50) and
inspection of the wind (3.114)
3.5
aperture card
card of standard dimensions with one or more openings into which a microfilm frame or frames can be
mounted or inserted
3.6
. . . . .
archival medium (deprecated)
recording material that can be expected to retain information (3.56) forever, so that such information can be
retrieved without significant loss when properly stored
NOTE However, as no such material exists, this is a deprecated term and as such is not to be used in International
Standards or system specifications.
3.7
Arrhenius plot
plot of the logarithm of the time for a given change in a characteristic proportional to the reaction rate (dye loss,
tensile strength change, D yellowing, etc.) versus the reciprocal of the temperature expressed in kelvins
min
NOTE The Arrhenius plot can be used to predict behaviour at a temperature lower than that at which a test is run.
3.8
base
support in a recording material on which the emulsion layers or magnetic layer (and, if necessary, the back
layer) are coated
3.8.1
cellulose-acetate base
base for recording materials composed mainly of cellulose esters of acetic acid
3.8.2
cellulose-ester base
base for recording materials composed mainly of cellulose esters of acetic, propionic, or butyric acid, or
mixtures thereof
3.8.3
polyester base
base for recording materials composed mainly of a polymer of ethylene glycol and terephthalic acid (also
referred to as polyethylene terephthalate) or a polymer of ethylene glycol and 2,6-naphthalene-dicarboxylic
acid (also referred to as polyethylene naphthalate)
3.8.4
poly(ethylene terephthalate) base
polyester base for recording materials composed mainly of a polymer of ethylene glycol and terephthalic acid
3.9
blister
localized delamination that resembles a bubble
3.10
blocking
sticking together of similar or dissimilar materials in physical contact
cf. anti-blocking agent (3.3)
2 © ISO 2003 — All rights reserved
---------------------- Page: 10 ----------------------
SIST ISO 18913:2011
ISO 18913:2003(E)
3.11
brittleness
property of a material that causes it to crack or break when bent or flexed
3.12
can
metal or plastic container (3.20) for a roll of recording material, such as photographic film (3.79) or
magnetic tape
3.13
carrier
medium upon which information (3.56) is recorded
cf. medium (3.68)
3.14
carton
box
outer container (3.20) that can hold one or more individual units and which may be a fabrication of paper,
card stock or plastic
3.15
cartridge
housing for a roll of recording material, such as photographic film (3.79) or magnetic tape, wound on a single
hub (3.50) or reel (3.89)
cf. cassette (3.16)
3.16
cassette
housing for a roll of recording material, such as photographic film (3.79) or magnetic tape, whose ends are
attached to two hub(s) (3.50) or reel(s) (3.89)
cf. cartridge (3.15)
3.17
class 100 000 clean room
controlled environment in which the level of airborne contaminates meets the requirements of ISO 14644-1
3.18
compact disc
CD
optical disc (3.76) format in which the information (3.56) layer is located at one surface of a substrate and
the data can be read by an optical beam
NOTE Described in IEC 60908.
3.18.1
CD-ROM
read-only-medium compact disc
optical disc (3.76) to which information (3.76) is transferred during manufacture to certain areas in the
compact disc format and can be read many times
NOTE Described in ISO/IEC 10149.
3.18.2
CD-R
recordable compact disc
recordable optical disc (3.76) in which information (3.56) can be recorded (once) to certain areas in the
compact disc format and read many times
© ISO 2003 — All rights reserved 3
---------------------- Page: 11 ----------------------
SIST ISO 18913:2011
ISO 18913:2003(E)
3.18.3
CD-RW
rewritable compact disc
recordable optical disc (3.76) in which information (3.56) can be recorded to certain areas in the compact
disc format, erased and rerecorded many times, and read many times
3.19
conditioning
exposure of a specimen to air at a given relative humidity (3.52.2) and temperature until equilibrium is
reached
3.20
container
box, can or carton used for storage and shipping of recording materials
EXAMPLE The box into which a reel (3.89), cassette (3.16), cartridge (3.15) or shell (3.93) is placed.
NOTE Reels, cassettes, cartridges or shells are not containers.
3.20.1
insulated record container
storage box designed to withstand elevated temperatures and conforming to national standards and
regulations
3.21
copy
reproduction of the information (3.56) from a master
3.22
core
metal or plastic cylinder on which recording material is wound
cf. hub (3.50)
3.23
cupping
departure of film or paper from physical flatness characterized by the condition where the four corners of a
rectangular sheet turn up, but the edges do not
3.24
curl
departure of film, paper or magnetic tape from physical flatness with the tendency to curve into a cylindrical
shape
3.25
delamination
separation of a laminate into its constituent layers
3.26
optical density
density
degree of light absorption, reflection or scattering characteristics of a photographic image, expressed as the
logarithm to the base 10 of the ratio of incident radiant flux to the transmitted, reflected or scattered flux
3.26.1
printing density
optical density of a processed photographic image in which the incident radiant flux has the same spectral
energy distribution as the printer light source and the transmitted density is evaluated by a receiver having the
same spectral response as the print material
4 © ISO 2003 — All rights reserved
---------------------- Page: 12 ----------------------
SIST ISO 18913:2011
ISO 18913:2003(E)
3.26.2
projection density
optical density of a processed photographic image in which the angular distributions of the incident and
transmitted radiant flux are equal and specified
3.26.3
visual density
optical density of a processed photographic image in which the incident radiant flux has a spectral energy
distribution as defined in ISO 5-3 and the transmitted or reflected radiant flux is evaluated by the human eye
or by a receiver having the same spectral response as the human eye
3.27
dew point
temperature at which moisture begins to condense on a surface, corresponding to saturation for a given
absolute humidity (3.52.1)
EXAMPLE The more humid the air, the higher the dew-point temperature.
See, also, relative humidity (3.52.2).
3.28
differential dimensional change
difference between the dimensional changes of the material in the two principal directions (length and width)
NOTE Polyester-based films frequently have maximum and minimum dimensional changes in directions other than
the length or width. These can be determined by rotating and viewing the uncoated base between a pair of crossed
polarizers. When the direction corresponding to either the maximum or minimum dimensional change is coincident with
the optical axis of one polarizer, there is minimum light transmission through the base.
3.29
digital versatile disc
DVD
optical disc (3.76) format in which one or more information (3.56) layers are located between two substrates
and the data can be read by an optical beam
NOTE Formerly called digital video disc.
3.30
dimensional change
〈processing alone〉 permanent dimensional change caused by photographic processing
NOTE This can be the conventional wet chemical processing, vapour processing or heat processing. The
dimensional change is measured after conditioning at the same relative humidity (3.52.2) and temperature as used for
the original measurement and is expressed as a percentage.
3.31
dimensional change
〈processing and ageing together〉 permanent dimensional change that occurs as a result of processing plus
ageing of the processed material
NOTE It is measured after conditioning of the processed, aged film or paper at the same relative humidity (3.52.2)
and temperature as used for the original measurement and is expressed as a percentage.
3.32
dimensional hysteresis
difference in the absolute dimensions of a specimen in equilibrium with air at a given relative humidity
(3.52.2), when conditioned from a higher relative humidity and when conditioned from a lower relative humidity
© ISO 2003 — All rights reserved 5
---------------------- Page: 13 ----------------------
SIST ISO 18913:2011
ISO 18913:2003(E)
3.33
duplicate
reproduction of a master, retaining the same polarity and size
3.34
emulsion layer
image or image-forming layer of photographic film (3.79), paper and plate
3.35
encapsulation
sealing of all edges of a specimen that has been laminated on both front and back surfaces
NOTE This process is usually done by laminating with sheets whose dimensions are larger than the specimen's and
then sealing at the overlaps.
3.36
enclosure
folder, envelope, sleeve or clam shell that is intended for physical protection against mechanical damage
3.36.1
open enclosure
enclosure that is intended for physical protection against mechanical damage, but is neither light-tight nor
airtight
EXAMPLE Spool, reel (3.89), core (3.22), cassette (3.16), magazine, folder, envelope, carton, box, sleeve,
transparency mount or aperture card.
3.36.2
photographic enclosure
container (3.20) in close or direct contact with photographic plates, films or papers such as reels, cans, bags,
folders, sleeves (sheaths), jackets, envelopes, window mounts or mats, slide mounts, cartons, boxes and
aperture cards
3.36.3
protective enclosure
impermeable sealed container (3.20), which could also by necessity be opaque, used for protection from
outside factors such as reactive gases and moisture, including changes in relative humidity (3.52.2), and
from light in the case of certain kinds of products
NOTE Such enclosures can be taped cans and sealed envelopes.
3.36.4
storage enclosure
item in close or direct contact with recording material
EXAMPLE Folder, envelope, sleeve, album (3.2), mat, cartridge (3.15) or cassette (3.16).
3.37
envelope
bag
enclosure (3.36) that is sealed with adhesive, mechanically joined or heat-sealed on two-edges with a bottom
fold and one side open
3.38
extended-term storage conditions
storage conditions suitable for the preservation of recorded information (3.56) having permanent value
6 © ISO 2003 — All rights reserved
---------------------- Page: 14 ----------------------
SIST ISO 18913:2011
ISO 18913:2003(E)
3.39
ferrotyping
glazing
changing of surface characteristics resulting from contact of two surfaces
3.40
fire-protective storage
facility designed to protect records against excessive temperatures, water and other fire-fighting agents, and
steam developed by insulation of safes or caused by the extinguishing of fires and collapsing structures
3.41
fire-resistant vault
fire-resistant vault as defined in appropriate national standards and regulations
3.42
flange
fixed or removable circular disc that is connected to the hub (3.50) to make a reel (3.89) for the purpose of
protecting the roll of recording materials
cf. reel (3.89)
3.43
folder
single sheet that is folded, does not have adhesive seams, and can be made from either paper or plastic
3.44
folding endurance
measure of fatigue resistance after multiple flexing
3.45
frost point
temperature to which moisture-laden air must be cooled for frost or ice formation
3.46
full reversal processing
processing of a photographic film (3.79) or paper to produce a positive image using bleach and
redeve
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.