Non-alloy steel wire rod for conversion to wire — Part 3: Specific requirements for rimmed and rimmed-substitute, low-carbon steel wire rod

Fil-machine en acier non allié destiné à la fabrication de fils — Partie 3: Exigences spécifiques au fil-machine en acier effervescent ou pseudo-effervescent à bas carbone

General Information

Status
Withdrawn
Publication Date
29-Aug-2001
Withdrawal Date
29-Aug-2001
Current Stage
9599 - Withdrawal of International Standard
Completion Date
29-Jun-2011
Ref Project

Relations

Buy Standard

Standard
ISO 16120-3:2001 - Non-alloy steel wire rod for conversion to wire
English language
3 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 16120-3
First edition
2001-08-15
Non-alloy steel wire rod for conversion to
wire —
Part 3:
Specific requirements for rimmed and
rimmed-substitute, low-carbon steel wire
rod
Fil-machine en acier non allié destiné à la fabrication de fils —
Partie 3: Exigences spécifiques au fil-machine en acier effervescent ou
pseudo-effervescent à bas carbone
Reference number
ISO 16120-3:2001(E)
©
ISO 2001

---------------------- Page: 1 ----------------------
ISO 16120-3:2001(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not
be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this
file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this
area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2001
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body
in the country of the requester.
ISO copyright office
Case postale 56 � CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.ch
Web www.iso.ch
Printed in Switzerland
ii © ISO 2001 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 16120-3:2001(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this part of ISO 16120 may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
International Standard ISO 16120-3 was prepared by Technical Committee ISO/TC 17, Steel, Subcommittee
SC 17, Steel wire rod and wire products.
This first edition of ISO 16120-3 together with parts 1, 2 and 4 cancels and replaces ISO 8457-2 (1989) which has
been technically revised and augmented.
ISO 16120 consists of the following parts, under the general title Non-alloy steel wire rod for conversion to wire:
� Part 1: General requirements
� Part 2: Specific requirements for general purpose wire rod
� Part 3: Specific requirements for rimmed and rimmed-substitute, low-carbon steel wire rod
� Part 4: Specific requirements for wire rod for special applications
© ISO 2001 – All rights reserved iii

---------------------- Page: 3 ----------------------
INTERNATIONAL STANDARD ISO 16120-3:2001(E)
Non-alloy steel wire rod for conversion to wire —
Part 3:
Specific requirements for rimmed and rimmed substitute low
carbon steel wire rod
1 Scope
This part of ISO 16120 is applicable to wire rod of low carbon, low silicon, rimmed and rimmed substitute steel with
high ductility intended for drawing and/or cold rolling.
NOTE Rimmed substitute steel: continuously cast steel designed to substitute the traditional rimming steel for drawability
and formability.
2 Normative references
The following normative documents contain provisions which, through reference in this text, constitute provisi
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.