ISO/FDIS 12843

Plain bearings — Reuse, recycling and disposal of plain bearing materials

This document gives how to effectively utilize material resources by recycling and reusing plain bearing materials and how to reduce the environmental load when disposing plain bearings.

Paliers lisses — Réutilisation, recyclage et entreposage des matériaux pour les paliers lisses

General Information

• Status: Not Published
• ICS: 13.030.50 - Recycling
• ICS: 21.100.10 - Plain bearings
• Technical Committee: ISO/TC 123/SC 6 - Terms and common items
• Drafting Committee: ISO/TC 123/SC 6 - Terms and common items
• Current Stage: 5020 - FDIS ballot initiated: 2 months. Proof sent to secretariat
• Start Date: 14-May-2024
• Completion Date: 14-May-2024

Standards Content (Sample)

FINAL DRAFT
International
Standard
ISO/FDIS 12843
ISO/TC 123/SC 6
Plain bearings — Reuse, recycling
Secretariat: JISC
and disposal of plain bearing
Voting begins on:
materials
2024-05-14
Paliers lisses — Réutilisation, recyclage et entreposage des
Voting terminates on:
matériaux pour les paliers lisses
2024-07-09
RECIPIENTS OF THIS DRAFT ARE INVITED TO SUBMIT,
WITH THEIR COMMENTS, NOTIFICATION OF ANY
RELEVANT PATENT RIGHTS OF WHICH THEY ARE AWARE
AND TO PROVIDE SUPPOR TING DOCUMENTATION.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO­
LOGICAL, COMMERCIAL AND USER PURPOSES, DRAFT
INTERNATIONAL STANDARDS MAY ON OCCASION HAVE
TO BE CONSIDERED IN THE LIGHT OF THEIR POTENTIAL
TO BECOME STAN DARDS TO WHICH REFERENCE MAY BE
MADE IN NATIONAL REGULATIONS.
Reference number
ISO/FDIS 12843:2024(en) © ISO 2024

---------------------- Page: 1 ----------------------
FINAL DRAFT
ISO/FDIS 12843:2024(en)
International
Standard
ISO/FDIS 12843
ISO/TC 123/SC 6
Plain bearings — Reuse, recycling
Secretariat: JISC
and disposal of plain bearing
Voting begins on:
materials
Paliers lisses — Réutilisation, recyclage et entreposage des
Voting terminates on:
matériaux pour les paliers lisses
RECIPIENTS OF THIS DRAFT ARE INVITED TO SUBMIT,
COPYRIGHT PROTECTED DOCUMENT
WITH THEIR COMMENTS, NOTIFICATION OF ANY
RELEVANT PATENT RIGHTS OF WHICH THEY ARE AWARE
AND TO PROVIDE SUPPOR TING DOCUMENTATION.
© ISO 2024
IN ADDITION TO THEIR EVALUATION AS
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO­
LOGICAL, COMMERCIAL AND USER PURPOSES, DRAFT
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
INTERNATIONAL STANDARDS MAY ON OCCASION HAVE
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
TO BE CONSIDERED IN THE LIGHT OF THEIR POTENTIAL
or ISO’s member body in the country of the requester.
TO BECOME STAN DARDS TO WHICH REFERENCE MAY BE
MADE IN NATIONAL REGULATIONS.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Email: [e-mail]
Website: www.iso.org
Published in Switzerland Reference number
ISO/FDIS 12843:2024(en) © ISO 2024

© ISO 2024 – All rights reserved
ii

---------------------- Page: 2 ----------------------
ISO/FDIS 12843:2024(en)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Treatment of used plain bearings . 1
5 Guidelines . 2
5.1 Design stage of plain bearings . .2
5.2 Manufacturing stage of plain bearings .2
5.3 Operating stage of plain bearings .3
5.4 Disposal of plain bearings .3
Bibliography .
...

ISO/DISFDIS 12843:2023(E)
ISO/TC 123/SC 6
Secretariat: JISC
Date: 2024-04-0530
Plain bearings — Reuse, recycling and disposal of plain bearing
materials
Paliers lisses — Réutilisation, recyclage et entreposage des matériaux pour les paliers lisses
FDIS stage

---------------------- Page: 1 ----------------------
ISO/FDIS 12843:2024(en)
© ISO 20232024
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication
may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying,
or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO
at the address below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: + 41 22 749 01 11
EmailE-mail: [e-mail]
Website: www.iso.org
Published in Switzerland
© ISO 2024 – All rights reserved
ii

---------------------- Page: 2 ----------------------
ISO/FDIS 12843:2024(en)
Contents
Foreword . iv
Introduction . v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Treatment of used plain bearings . 1
5 Guidelines . 2
5.1 Design stage of plain bearings . 2
5.2 Manufacturing stage of plain bearings . 3
5.3 Operating stage of plain bearings . 3
5.4 Disposal of plain bearings. 3
Bibliography . 5

© ISO 2024 – All rights reserved
iii

---------------------- Page: 3 ----------------------
ISO/FDIS 12843:2024(en)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types of
ISO document should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent rights
in respect thereof. As of the date of publication of this document, ISO [had/had not] received notice of (a)
patent(s) which may be required to implement this document. However, implementers are cautioned that this
may not represent the latest information, which may be obtained from the patent database available at
www.iso.org/patents. ISO shall not be held responsible for identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitu
...