ISO 1035
(Main)Hot-rolled steel bars — Dimensions, shape, masses and tolerances
Hot-rolled steel bars — Dimensions, shape, masses and tolerances
This document specifies dimensions, shape, mass and tolerances of metric series hot-rolled steel bars. This document is applicable to: hot-rolled round bars with diameter of 5,5 mm up to 400 mm; hot-rolled square bars with side length of 5,5 mm up to 300 mm; hot-rolled flat bars with thickness of 3 mm up to 60 mm and width of 10 mm up to 200 mm; hot-rolled hexagonal bars with distance across opposite flats of 8 mm up to 70 mm; hot-rolled octagonal bars with distance across opposite flats of 16 mm up to 40 mm. NOTE Wide flats can be covered under flat bars for practical reasons.
Barres en acier laminées à chaud — Dimensions, formes, masses et tolérances
General Information
- Status
- Not Published
- Technical Committee
- ISO/TC 17/SC 3 - Steels for structural purposes
- Current Stage
- 6000 - International Standard under publication
- Start Date
- 04-Apr-2026
- Completion Date
- 09-May-2026
Relations
- Effective Date
- 01-Jun-2024
- Effective Date
- 01-Jun-2024
- Effective Date
- 01-Jun-2024
- Effective Date
- 01-Jun-2024
Overview
ISO 1035: Hot-rolled Steel Bars - Dimensions, Shape, Masses, and Tolerances is the international standard that specifies the dimensional characteristics, shape requirements, mass per unit length, and permissible manufacturing tolerances for hot-rolled steel bars. Developed by the International Organization for Standardization (ISO) under Technical Committee ISO/TC 17/SC 3, this standard establishes a metric series for round, square, flat, hexagonal, and octagonal steel bars widely used in structural, engineering, and manufacturing industries.
The scope of ISO 1035 covers:
- Hot-rolled round bars: diameters from 5.5 mm to 400 mm
- Hot-rolled square bars: side lengths from 5.5 mm to 300 mm
- Hot-rolled flat bars: thicknesses from 3 mm to 60 mm, widths from 10 mm to 200 mm
- Hot-rolled hexagonal bars: distance across flats from 8 mm to 70 mm
- Hot-rolled octagonal bars: distance across flats from 16 mm to 40 mm
This standard ensures consistent quality and interchangeability for products in global supply chains.
Key Topics
ISO 1035 thoroughly defines the following aspects of hot-rolled steel bars:
Designation System: Standardizes how steel bars are identified, specifying type, dimensions, tolerance class, and steel grade.
Cross-sectional Forms: Details the standardized shapes - round, square, flat, hexagonal, and octagonal - with accompanying diagrams for clarity.
Dimensions and Masses: Provides comprehensive tables listing preferred sizes, sectional areas, and masses per meter for each bar shape.
Tolerances:
- Dimensional tolerances for diameters, width, and thickness
- Length tolerances and options for symmetrical tolerances
- Ovality (for round bars), squareness (for square and flat bars), and straightness
- Special tolerance classes (Normal, Fine, Superfine) for specific applications
Shape and Straightness: Defines permissible deviations in shape, including ovality, out-of-squareness, twist, and straightness tolerances, ensuring bars meet the rigorous requirements of diverse engineering applications.
Applications
Hot-rolled steel bars meeting ISO 1035 requirements are widely used in:
- Construction and Infrastructure: Reinforcement, frameworks, and general structural applications where consistent dimensions and tolerances are critical for safety and structural integrity.
- Automotive and Machinery Manufacturing: Production of components, shafts, and machine elements that require precise and reliable steel bar inputs.
- Engineering and Fabrication: Custom fabrication of machinery, tools, and industrial parts where adherence to dimensional requirements is essential for performance.
- Steel Processing: As intermediate products for further processing like forging, machining, or cold-forming, where starting material consistency results in improved end-product quality and efficiency.
Related Standards
To ensure comprehensive compliance and compatibility, consider these important standards related to ISO 1035:
- ISO 6929: Steel products - Vocabulary
- ISO 630 series: Structural steels - General and specific technical delivery conditions
- ISO 7452: Hot-rolled steel plates - Tolerances on dimensions and shape
- EN 10058, EN 10059, EN 10060, EN 10061: European standards for hot-rolled bars (flats, squares, rounds, hexagons)
- ASTM A6M: Specification for general requirements for rolled structural steel bars, plates, and shapes
- GB/T 702: Chinese national standard for hot-rolled steel bars
- JIS G 3191 & G 3194: Japanese standards for dimensions and permissible variations of hot-rolled steel bars
Adhering to ISO 1035 ensures global compatibility, product quality, and simplifies procurement for technical buyers, engineers, and manufacturers in diverse industries worldwide.
Buy Documents
ISO/FDIS 1035 - Hot-rolled steel bars — Dimensions, shape, masses and tolerances Released:23. 01. 2026
REDLINE ISO/FDIS 1035 - Hot-rolled steel bars — Dimensions, shape, masses and tolerances Released:23. 01. 2026
Get Certified
Connect with accredited certification bodies for this standard

Element Materials Technology
Materials testing and product certification.
Inštitut za kovinske materiale in tehnologije
Institute of Metals and Technology. Materials testing, metallurgical analysis, NDT.
Sponsored listings
Frequently Asked Questions
ISO 1035 is a draft published by the International Organization for Standardization (ISO). Its full title is "Hot-rolled steel bars — Dimensions, shape, masses and tolerances". This standard covers: This document specifies dimensions, shape, mass and tolerances of metric series hot-rolled steel bars. This document is applicable to: hot-rolled round bars with diameter of 5,5 mm up to 400 mm; hot-rolled square bars with side length of 5,5 mm up to 300 mm; hot-rolled flat bars with thickness of 3 mm up to 60 mm and width of 10 mm up to 200 mm; hot-rolled hexagonal bars with distance across opposite flats of 8 mm up to 70 mm; hot-rolled octagonal bars with distance across opposite flats of 16 mm up to 40 mm. NOTE Wide flats can be covered under flat bars for practical reasons.
This document specifies dimensions, shape, mass and tolerances of metric series hot-rolled steel bars. This document is applicable to: hot-rolled round bars with diameter of 5,5 mm up to 400 mm; hot-rolled square bars with side length of 5,5 mm up to 300 mm; hot-rolled flat bars with thickness of 3 mm up to 60 mm and width of 10 mm up to 200 mm; hot-rolled hexagonal bars with distance across opposite flats of 8 mm up to 70 mm; hot-rolled octagonal bars with distance across opposite flats of 16 mm up to 40 mm. NOTE Wide flats can be covered under flat bars for practical reasons.
ISO 1035 is classified under the following ICS (International Classification for Standards) categories: 77.140.60 - Steel bars and rods. The ICS classification helps identify the subject area and facilitates finding related standards.
ISO 1035 has the following relationships with other standards: It is inter standard links to ISO 1035-1:1980, ISO 1035-2:1980, ISO 1035-4:1982, ISO 1035-3:1980. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.
ISO 1035 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.
Standards Content (Sample)
FINAL DRAFT
International
Standard
ISO/FDIS 1035
ISO/TC 17/SC 3
Hot-rolled steel bars — Dimensions,
Secretariat: AFNOR
shape, masses and tolerances
Voting begins on:
Barres en acier laminées à chaud — Dimensions, formes, masses 2026-02-06
et tolérances
Voting terminates on:
2026-04-03
RECIPIENTS OF THIS DRAFT ARE INVITED TO SUBMIT,
WITH THEIR COMMENTS, NOTIFICATION OF ANY
RELEVANT PATENT RIGHTS OF WHICH THEY ARE AWARE
AND TO PROVIDE SUPPOR TING DOCUMENTATION.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO
LOGICAL, COMMERCIAL AND USER PURPOSES, DRAFT
INTERNATIONAL STANDARDS MAY ON OCCASION HAVE
TO BE CONSIDERED IN THE LIGHT OF THEIR POTENTIAL
TO BECOME STAN DARDS TO WHICH REFERENCE MAY BE
MADE IN NATIONAL REGULATIONS.
Reference number
ISO/FDIS 1035:2026(en) © ISO 2026
FINAL DRAFT
ISO/FDIS 1035:2026(en)
International
Standard
ISO/FDIS 1035
ISO/TC 17/SC 3
Hot-rolled steel bars — Dimensions,
Secretariat: AFNOR
shape, masses and tolerances
Voting begins on:
Barres en acier laminées à chaud — Dimensions, formes, masses
et tolérances
Voting terminates on:
RECIPIENTS OF THIS DRAFT ARE INVITED TO SUBMIT,
WITH THEIR COMMENTS, NOTIFICATION OF ANY
RELEVANT PATENT RIGHTS OF WHICH THEY ARE AWARE
AND TO PROVIDE SUPPOR TING DOCUMENTATION.
© ISO 2026
IN ADDITION TO THEIR EVALUATION AS
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO
LOGICAL, COMMERCIAL AND USER PURPOSES, DRAFT
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
INTERNATIONAL STANDARDS MAY ON OCCASION HAVE
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
TO BE CONSIDERED IN THE LIGHT OF THEIR POTENTIAL
or ISO’s member body in the country of the requester.
TO BECOME STAN DARDS TO WHICH REFERENCE MAY BE
MADE IN NATIONAL REGULATIONS.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland Reference number
ISO/FDIS 1035:2026(en) © ISO 2026
ii
ISO/FDIS 1035:2026(en)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Designation . 1
5 Cross-sectional form . 2
6 Dimensions, masses and tolerances . . 3
6.1 Dimensions and masses.3
6.2 Tolerances on dimensions .4
7 Shape . 5
Annex A (informative) Dimensions, sectional areas and masses per unit length of hot-rolled
steel bars .10
Bibliography . 19
iii
ISO/FDIS 1035:2026(en)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO document should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent
rights in respect thereof. As of the date of publication of this document, ISO had not received notice of (a)
patent(s) which may be required to implement this document. However, implementers are cautioned that
this may not represent the latest information, which may be obtained from the patent database available at
www.iso.org/patents. ISO shall not be held responsible for identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions
related to conformity assessment, as well as information about ISO's adherence to the World Trade
Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 17, Steels, Subcommittee SC 3, Steels for
structural purposes.
This first edition of ISO 1035 cancels and replaces ISO 1035-1:1980, ISO 1035-2:1980, ISO 1035-3:1980 and
The main changes are as follows:
— figures illustrating forms of hot-rolled bars have been added;
— the category of dimensions and second preference dimensions has been cancelled;
— upper limits of dimensions and dimensional tolerances for hot-rolled round, square and flat bars have
been revised;
— dimensions for hexagonal and octagonal bars have been added;
— requirement for maximum permissible value for hot-rolled flat bars was added.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iv
FINAL DRAFT International Standard ISO/FDIS 1035:2026(en)
Hot-rolled steel bars — Dimensions, shape, masses and
tolerances
1 Scope
This document specifies dimensions, shape, mass and tolerances of metric series hot-rolled steel bars.
This document is applicable to:
a) hot-rolled round bars with diameter of 5,5 mm up to 400 mm;
b) hot-rolled square bars with side length of 5,5 mm up to 300 mm;
c) hot-rolled flat bars with thickness of 3 mm up to 60 mm and width of 10 mm up to 200 mm;
d) hot-rolled hexagonal bars with distance across opposite flats of 8 mm up to 70 mm;
e) hot-rolled octagonal bars with distance across opposite flats of 16 mm up to 40 mm.
NOTE Wide flats can be covered under flat bars for practical reasons.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content constitutes
requirements of this document. For dated references, only the edition cited applies. For undated references,
the latest edition of the referenced document (including any amendments) applies.
ISO 6929, Steel products — Vocabulary
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 6929 apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https:// www .iso .org/ obp
— IEC Electropedia: available at https:// www .electropedia .org/
4 Designation
The designation of hot-rolled steel bars shall comprise:
— the term round bar, square bar, flat bar, hexagonal or octagonal bar;
— the number of the standard, i.e. ISO 1035;
— the nominal dimension(s) in mm and the tolerance classes;
— the number of the quality standard and the steel name of the ordered steel.
EXAMPLE
Round bar ISO 1035-50 N×6000L0
ISO/FDIS 1035:2026(en)
Steel ISO 630-2 S355D
5 Cross-sectional form
5.1 Cross-sectional forms of hot-rolled round bars and square bars are shown in Figure 1.
a) b)
Key
d diameter
a side length
Figure 1 — Cross-sectional forms of hot-rolled round bars and square bars
5.2 Cross-sectional form of hot-rolled flat bars is shown in Figure 2.
Key
w width
t thickness
Figure 2 — Cross-sectional form of hot-rolled flat bars
5.3 Cross-sectional forms of hot-rolled hexagonal and octagonal bars are shown in Figure 3.
ISO/FDIS 1035:2026(en)
a) b)
Key
S distance across flats
Figure 3 — Cross-sectional forms of hot-rolled hexagonal and octagonal bars
6 Dimensions, masses and tolerances
6.1 Dimensions and masses
6.1.1 The preferred dimensions and masses per unit length of hot-rolled round bars are given in Table A.1.
6.1.2 The preferred dimensions and masses per unit length of hot-rolled square bars are given in Table A.2.
6.1.3 The preferred dimensions and masses per unit length of hot-rolled flat bars are given in Table A.3.
6.1.4 The preferred dimensions, sectional areas and masses per unit length of hot-rolled hexagonal and
octagonal bars are given in Table A.4.
6.1.5 Upon agreement between the supplier and purchaser, steel bars may be delivered in other dimensions
unlisted in Annex A, and it shall be indicated in the contract.
ISO/FDIS 1035:2026(en)
6.2 Tolerances on dimensions
6.2.1 The tolerances on diameter for round bars and side length for square bars shall be as specified
in Table 1. The class of dimensional tolerance shall be indicated in the contract. If no tolerance class is
requested, the tolerance class is N.
Table 1 — Tolerances on diameter for round bars and side length for square bars
Tolerance on diameters or side lengths for classes
Nominal diameters or side lengths
mm
mm
N F S
5,5-15 ±0,40 ±0,30 ±0,20
>15-25 ±0,50 ±0,40 ±0,25
>25-35 ±0,60 ±0,50 ±0,30
>35-50 ±0,80 ±0,60 ±0,40
>50-80 ±1,00 ±0,80 ±0,50
>80-100 ±1,30 ±1,00 ±0,90
>100-120 ±1,60 ±1,30 ±1,20
>120-160 ±2,00 ±1,60 ±1,40
>160-200 ±2,50 ±2,00 ±1,60
>200-280 ±3,00 ±2,50 ±2,00
>280-310 ±4,00 ±3,00 ±2,50
>310-380 ±5,00 ±4,00 ±3,00
>380-400 ±6,00 ±5,00 ±4,00
Note: N=normal, F=fine, S=superfine.
6.2.2 The tolerances on width and thickness of hot-rolled steel flat bars shall be as specified in Table 2 and
Table 3.
6.2.3 Tolerances of thickness and width shall not apply for the part of out-of-squareness.
Table 2 — Tolerances on width for hot-rolled flat bars
Nominal widths Tolerances on width
mm mm
10-50 ±0,80
>50-75 ±1,20
>75-100 ±1,50
>100-125 ±2,00
>125-150 ±2,50
>150-200 To be agreed between the supplier and purchaser
Table 3 — Tolerances on thickness for hot-rolled flat bars
Tolerances on thicknesses for nominal widths (w)
Nominal thicknesses
mm
mm
w≤50 50
3-20 ±0,40 ±0,50
To be agreed between the supplier and
>20-40 ±0,80 ±1,00
purchaser
>40-60 — ±1,50
ISO/FDIS 1035:2026(en)
6.2.4 The distance across flats and tolerances of hot-rolled hexagonal and octagonal bars shall be in
accordance with Table 4. The class of tolerances shall be indicated in the contract.
Table 4 — Distance across flats and tolerances for hot-rolled hexagonal and octagonal bars
Tolerance for classes
Distance across flats
mm
mm
N F
8-15 ±0,40 ±0,30
>15-25 ±0,50 ±0,40
>25-35 ±0,60 ±0,50
>35-50 ±0,80 ±0,60
>50-70 ±1,00 ±0,80
6.2.5 The tolerances on length shall be as specified in Table 5. If no tolerance class is requested, the
tolerance class is L1.
Table 5 — Tolerances on length
Tolerances on length for class
mm
Nominal lengths
L0 L1 L2 L3 L4
0 0 0
a c
All ±200
b b b
+100 +50 +25
a
The length of the bar is left to the choice of the manufacturer, it shall be not less than 3 000 mm. If agreed between the
purchaser and the manufacturer, other dimensions and tolerances may be used.
b
When agreed at the time of ordering, the bars can be supplied with symmetrical “±” tolerances. In this case, the total
tolerance range shall be the same as specified for the relevant “+” tolerances (for example ±25 mm instead of 0 +50 mm. Possible
short-length may appear, their percentage and minimum length has to be agreed on during the order.
c
Tighter tolerances in cases where cold cutting is possible might be agreed at the time of enquiry and order.
6.2.6 Upon agreement between the supplier and purchaser, other dimensional tolerances of steel bars
may be used and it shall be indicated in the contract.
7 Shape
7.1 The permissible ovality for all diameters of round bars, measured as the difference between the
maximum and minimum diameters of the same cross-section, shall not exceed 75 % of the total tolerance
specified on the diameter according to Table 1. If agreed between the purchaser and the manufacturer, other
ovality may be used.
7.2 The permissible out-of-squareness for all side lengths of square bars, measured as the difference of
the distance between
...
ISO/DISFDIS 1035:2025(en)
ISO /TC 17/SC3SC 3
Secretariat: AFNOR
Date:2025-09-29 2026-01-23
Hot-rolled steel bars — Dimensions, shape, masses and tolerances
Barres en acier laminées à chaud — Dimensions, formes, masses et tolérances
FDIS stage
ISO/FDIS 1035:2026(en)
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication
may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying,
or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO
at the address below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: + 41 22 749 01 11
EmailE-mail: copyright@iso.org
Website: www.iso.orgwww.iso.org
Published in Switzerland
ii
ISO/DISFDIS 1035:20252026(en)
Contents
Foreword . iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Designation . 2
5 Cross-sectional form . 2
6 Dimensions, masses and tolerances . 4
7 Shape . 7
Annex A (informative) Dimensions, sectional areas and masses per unit length of hot-rolled
steel bars . 15
Bibliography . 8
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Designation . 5
5 Cross-sectional form . 6
6 Dimensions, masses and tolerances . 7
6.1Dimensions and masses . 7
6.2 Tolerances on dimensions . 7
6.3 Tolerances on length . 9
7 Shape . 9
Annex A (informative) . 13
Bibliography . 20
iii
ISO/FDIS 1035:2026(en)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types of
ISO document should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent rights
in respect thereof. As of the date of publication of this document, ISO had not received notice of (a) patent(s)
which may be required to implement this document. However, implementers are cautioned that this may not
represent the latest information, which may be obtained from the patent database available at
www.iso.org/patents.www.iso.org/patents. ISO shall not be held responsible for identifying any or all such
patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions
related to conformity assessment, as well as information about ISO's adherence to the World Trade
Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.htmlwww.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 17, Steels, Subcommittee SC 3, Steels for
structural purposes.
This first edition of ISO 1035 cancels and replaces ISO 1035-1:1980, ISO 1035-2:1980, ISO 1035-3:1980 and
The main changes are as follows:
— —figures illustrating forms of hot-rolled bars werehave been added. ;
— —the category of dimensions and second preference dimensions was canceled.has been cancelled;
— —upper limits of dimensions and dimensional tolerances for hot-rolled round, square and flat bars have
been revised.;
— —dimensions for hexagonal and octagonal bars werehave been added.;
— —requirement for maximum permissible value for hot-rolled flat bars was added.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iv
DRAFT International Standard ISO/DIS 1035:2025(en)
Hot-rolled steel bars — Dimensions, shape, masses and
tolerances
1 Scope
This document specifies dimensions, shape, mass and tolerances of metric series hot-rolled steel bars.
This document is applicable to:
a) a) hot-rolled round bars with diameter of 5,5 mm up to 400 mm;
b) b) hot-rolled square bars with side length of 5,5 mm up to 300 mm;
c) c) hot-rolled flat bars with thickness of 3 mm up to 60 mm and width of 10 mm up to
200 mm;
d) d) hot-rolled hexagonal bars with distance across opposite flats of 8 mm up to 70 mm;
e) e) hot-rolled octagonal bars with distance across opposite flats of 16 mm up to 40 mm.
NOTE Wide flats maycan be covered under flat bars for practical reasons.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
ISO 6929, Steel products — Vocabulary
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 6929 apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— — ISO Online browsing platform: available at
https://www.iso.org/obphttps://www.iso.org/obp
ISO/DIS 1035:2025(en)
— — IEC Electropedia: available at https://www.electropedia.org/https://www.electropedia.org/
4 Designation
The designation of hot-rolled steel bars shall comprise:
— — the term round bar, square bar, flat bar, hexagonal or octagonal bar;
— — the number of the standard, i.e. ISO 1035;
— — the nominal dimension(s) in mm and the tolerance classes;
— — the number of the quality standard and the steel name of the ordered steel.
EXAMPLE:
Round bar ISO 1035-50 N×6000L0
Steel ISO 630-2 S355D
5 Cross-sectional form
5.1 5.1 Cross-sectional forms of hot-rolled round bars and square bars are shown in
Figure 1.0.
a) b)
ISO/DIS 1035:2025(en)
Key
d diameter
a side length
Figure 1 — Cross-sectional forms of hot-rolled round bars and square bars
5.2 5.2 Cross-sectional form of hot-rolled flat bars is shown in Figure 2.0.
Key
w width
t thickness
Figure 2 — Cross-sectional form of hot-rolled flat bars
5.3 5.3 Cross-sectional forms of hot-rolled hexagonal and octagonal bars are shown in
Figure 3.0.
ISO/DIS 1035:2025(en)
a) b)
Key
S distance across flats
Figure 3 — Cross-sectional forms of hot-rolled hexagonal and octagonal bars
6 Dimensions, masses and tolerances
6.1 Dimensions and masses
6.1.1 6.1.1 The preferred dimensions and masses per unit length of hot-rolled round bars are
given in Table A.1.0.
6.1.2 6.1.2 The preferred dimensions and masses per unit length of hot-rolled square bars are
given in Table A.2.0.
6.1.3 6.1.3 The preferred dimensions and masses per unit length of hot-rolled flat bars are given
in Table A.3.0.
ISO/DIS 1035:2025(en)
6.1.4 6.1.4 The preferred dimensions, sectional areas and masses per unit length of hot-rolled
hexagonal and octagonal bars are given in Table A.4.0.
6.1.5 6.1.5 Upon agreement between the supplier and purchaser, steel bars may be delivered in
other dimensions unlisted in Annex A,Annex A, and it shall be indicated in the contract.
6.2 Tolerances on dimensions
6.2.1 6.2.1 The tolerances on diameter for round bars and side length for square bars shall be as
specified in Table 1.0. The class of dimensional tolerance shall be indicated in the contract. If no
tolerance class is requested, the tolerance class is N.
Table 1 — Tolerances on diameter for round bars and side length for square bars
Tolerance on diameters or side lengths for classes
Nominal diameters or side
lengths mm
mm
N F S
5,5-15 ±0,40 ±0,30 ±0,20
>15-25 ±0,50 ±0,40 ±0,25
>25-35 ±0,60 ±0,50 ±0,30
>35-50 ±0,80 ±0,60 ±0,40
>50-80 ±1,00 ±0,80 ±0,50
>80-100 ±1,30 ±1,00 ±0,90
>100-120 ±1,60 ±1,30 ±1,20
>120-160 ±2,00 ±1,60 ±1,40
>160-200 ±2,50 ±2,00 ±1,60
>200-280 ±3,00 ±2,50 ±2,00
>280-310 ±4,00 ±3,00 ±2,50
>310-380 ±5,00 ±4,00 ±3,00
>380-400 ±6.,00 ±5.,00 ±4.,00
Note: N=normal, F=fine, S=superfine.
6.2.2 6.2.2 The tolerances on width and thickness of hot-rolled steel flat bars shall be as specified
in Table 20 and Table 3.0.
6.2.3 6.2.3 Tolerances of thickness and width shall not apply for the part of out-of-squareness.
Table 2 — Tolerances on width for hot-rolled flat bars
Nominal widths Tolerances on width
mm mm
10-50 ±0,80
>50-75 ±1,20
>75-100 ±1,50
ISO/DIS 1035:2025(en)
Nominal widths Tolerances on width
mm mm
>100-125 ±2,00
>125-150 ±2,50
>150-200 To be agreed between the supplier and purchaser
Table 3 — Tolerances on thickness for hot-rolled flat bars
Tolerances on thicknesses for nominal widths (w)
Nominal
mm
thicknesses
mm
w≤50 50
3-20 ±0,40 ±0,50
To be agreed between the supplier
>20-40 ±0,80 ±1,00
and purchaser
>40-60 — ±1,50
6.2.4 6.2.4 The distance across flats and tolerances of hot-rolled hexagonal and octagonal bars
shall be in accordance with Table 4.0. The class of tolerances shall be indicated in the contract.
Table 4 — Distance across flats and tolerances for hot-rolled hexagonal and octagonal bars
Tolerance for classes
Distance across flats
mm
mm
N F
8-15 ±0,40 ±0,30
>15-25 ±0,50 ±0,40
>25-35 ±0,60 ±0,50
>35-50 ±0,80 ±0,60
>50-70 ±1,00 ±0,80
6.2.5 6.2.5 The tolerances on length shall be as specified in Table 5.0. If no tolerance class is
requested, the tolerance class is L1.
Table 5 — Tolerances on length
Tolerances on length for class
mm
Nominal lengths
L0 L1 L2 L3 L4
0 0 0
a c
All ±200
b b b
+100 +50 +25
a The length of the bar is left to the choice of the manufacturer, it shall be not less than 3 000 mm. If agreed between the
purchaser and the manufacturer, other dimensions and tolerances may be used.
ISO/DIS 1035:2025(en)
Tolerances on length for class
mm
Nominal lengths
L0 L1 L2 L3 L4
b When agreed at the time of ordering, the bars can be supplied with symmetrical “±” tolerances. In this case, the total
tolerance range shall be the same as specified for the relevant “+” tolerances (for example ±25 mm instead of 0 +50 mm.
Possible short-length may appear, their percentage and minimum length has to be agreed on during the order.
c Tighter tolerances in cases where cold cutting is possible might be agreed at the time of enquiry and order.
6.2.6 6.2.6 Upon agreement between the supplier and purchaser, other dimensional tolerances of
steel bars may be used and it shall be indicated in the contract.
7 Shape
7.1 7.1 The permissible ovality for all diameters of round bars, measured as the difference
between the maximum and minimum diameters of the same cross-section, shall not exceed 75 % of
the total tolerance specified on the diameter according to Table 1.0. If agreed between the purchaser
and the manufacturer, other ovality may be used.
7.2 7.2 The permissible out-of-squareness for all side lengths of square bars, measured as the
difference of the distance between parallel faces of the same cross-section, shall not exceed 75 % of
the total tolerance specified on the nominal width of side in Table 1.0. If agreed between the
purchaser and the manufacturer, other out-of-square may be used. The out-of-squareness of square
bars are shown in Figure 40 a), b), c) and d).
ISO/DIS 1035:2025(en)
a) b)
ISO/DIS 1035:2025(en)
c) d)
Figure 4 — Out-of-squareness of hot-rolled square bars
7.3 7.3 The permissible out-of-section for all distances across flats of hexagonal and octagonal
bars, measured as the maximum difference in the distance across
...








Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...