ISO/PRF 24667
(Main)Sports and recreational facilities -- Impact surfacing testing device
Sports and recreational facilities -- Impact surfacing testing device
This document gives the specifications for impact attenuation testing equipment used to evaluate the impact performance characteristics of playground surfacing. Its specifications are aimed at ensuring that developers and manufacturers of such instruments meet minimum performance characteristics to allow repeatable, reproducible and accurate results. This document does not specify a test method. NOTE Such test methods are covered in other standards, e.g. EN 1177, ASTM F1292, ASTM F3313, AS 4422, CSA Z614.
Installations sportives et récréatives -- Dispositif d'essai de revêtement d'impact
Le présent document indique les spécifications de l'équipement d'essai de mesure de l'atténuation des impacts utilisé pour évaluer les caractéristiques de performance à l'impact des revêtements d'aires de jeux. Ces spécifications sont conçues pour s'assurer que les développeurs et les fabricants de tels instruments respectent les caractéristiques de performance minimales permettant d'obtenir des résultats répétables, reproductibles et exacts. Le présent document ne spécifie pas de méthode d'essai. NOTE 1 De telles méthodes d'essai sont couvertes par d'autres normes (par exemple, l'EN 1177, l'ASTM F1292, l'ASTM F3313, l'AS 4422 et la CSA Z614).
General Information
RELATIONS
Standards Content (sample)
INTERNATIONAL ISO
STANDARD 24667
First edition
Sports and recreational facilities —
Impact surfacing testing device
Installations sportives et récréatives — Dispositif d'essai de
revêtement d'impact
PROOF/ÉPREUVE
Reference number
ISO 24667:2021(E)
© ISO 2021
---------------------- Page: 1 ----------------------
ISO 24667:2021(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2021
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
PROOF/ÉPREUVE © ISO 2021 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 24667:2021(E)
Contents Page
Foreword ........................................................................................................................................................................................................................................iv
Introduction .................................................................................................................................................................................................................................v
1 Scope ................................................................................................................................................................................................................................. 1
2 Normative references ..................................................................................................................................................................................... 1
3 Terms and definitions .................................................................................................................................................................................... 1
4 Apparatus .................................................................................................................................................................................................................... 1
4.1 Missile (headform) .............................................................................................................................................................................. 1
4.2 Accelerometer ......................................................................................................................................................................................... 2
4.3 Data acquisition system ................................................................................................................................................................. 2
4.3.1 General ........................................................................................................................................................................................ 2
4.3.2 Channels ..................................................................................................................................................................................... 2
5 Calculation and processing .......................................................................................................................................................................3
6 Periodic calibration ..........................................................................................................................................................................................3
6.1 General ........................................................................................................................................................................................................... 3
6.2 Accelerometer ......................................................................................................................................................................................... 3
6.3 Data acquisition system ................................................................................................................................................................. 4
6.4 Reference pad .......................................................................................................................................................................................... 4
6.5 Missile profile .......................................................................................................................................................................................... 5
6.6 Calibration report ................................................................................................................................................................................ 5
Bibliography ................................................................................................................................................................................................................................ 6
iii© ISO 2021 – All rights reserved PROOF/ÉPREUVE
---------------------- Page: 3 ----------------------
ISO 24667:2021(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.This document was prepared by Technical Committee ISO/TC 83, Sports and other recreational facilities
and equipment.This first edition cancels and replaces ISO/TS 24667:2020, which has been technically revised.
The main changes are as follows:— Addition of a new Formula (1) and renumbering of the subsequent formulae.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.PROOF/ÉPREUVE © ISO 2021 – All rights reserved
---------------------- Page: 4 ----------------------
ISO 24667:2021(E)
Introduction
Impact attenuating surfacing has been shown to be fundamental to the prevention of 60 % to 75 %
of the injuries in playgrounds from impacts with the surface after a fall. The surface materials can be
sourced and installed locally, such as sand, wood chips or rounded gravel, while others can be sourced
from materials around the world and assembled on site such as poured in place rubber, tiles, mats or
synthetic turfs and installed at local playgrounds. The performance of installed surfacing materials
should be comparable from playground to playground no matter where the playground is situated. The
equipment used to measure the performance of playground surfacing is internationally consistent,
repeatable and reproducible.The field of impact attenuation measurement as it applies to playground safety surfaces is very small,
resulting in a limited market for potential manufacturers of such equipment. While a small number of
reputable manufacturers exist, organizations needing playground impact test equipment, such as test
laboratories and university researchers, often rely on their own technical abilities or those of related
engineering departments to create the needed equipment from scratch.© ISO 2021 – All rights reserved PROOF/ÉPREUVE
---------------------- Page: 5 ----------------------
INTERNATIONAL STANDARD ISO 24667:2021(E)
Sports and recreational facilities — Impact surfacing
testing device
1 Scope
This document gives the specifications for impact attenuation testing equipment used to evaluate the
impact performance characteristics of playground surfacing. The specifications are aimed at ensuring
that developers and manufacturers of such instruments meet minimum performance characteristics to
allow repeatable, reproducible and accurate results.This document does not specify a test method.
NOTE Such test methods are covered in other standards, e.g. EN 1177, ASTM F1292, ASTM F3313, AS 4422,
CSA Z614.2 Normat
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.