ISO 7752-3:2010
(Main)Cranes — Control layout and characteristics — Part 3: Tower cranes
Cranes — Control layout and characteristics — Part 3: Tower cranes
ISO 7752-3:2010 specifies the particular requirements for the controls of tower cranes as defined in ISO 4306-3 and the arrangement of those basic controls used for positioning loads. It is intended to be used in conjunction with ISO 7752-1, which gives general principles and requirements for the controls of all types of cranes.
Appareils de levage à charge suspendue — Disposition et caractéristiques des commandes — Partie 3: Grues à tour
L'ISO 7752-3:2010 spécifie les exigences particulières des commandes pour les grues à tour, telles que définies dans l'ISO 4306-3, ainsi que la disposition des organes de service de base utilisés pour le positionnement des charges. Elle est destinée à être utilisée conjointement à l'ISO 7752-1 qui établit les principes généraux et les exigences relatifs aux commandes des appareils de levage à charge suspendue.
Žerjavi - Namestitev in karakteristike kontrolne opreme - 3. del: Stolpni žerjavi
Ta del standarda ISO 7752 določa posebne zahteve za krmilje stolpnih žerjavov iz standarda ISO 4306-3 in razporeditev osnovnega krmilja, ki se uporablja za nameščanje bremen. Standard je treba uporabljati v povezavi s standardom ISO 7752-1, ki določa splošna načela in zahteve za krmilje vseh vrst žerjavov.
General Information
Relations
Buy Standard
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 7752-3
Second edition
2010-06-01
Cranes — Control layout and
characteristics —
Part 3:
Tower cranes
Appareils de levage à charge suspendue — Disposition et
caractéristiques des commandes —
Partie 3: Grues à tour
Reference number
ISO 7752-3:2010(E)
©
ISO 2010
---------------------- Page: 1 ----------------------
ISO 7752-3:2010(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
COPYRIGHT PROTECTED DOCUMENT
© ISO 2010
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2010 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 7752-3:2010(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 7752-3 was prepared by Technical Committee ISO/TC 96, Cranes, Subcommittee SC 7, Tower cranes.
This second edition cancels and replaces the first edition (ISO 7752-3:1993), which has been technically
revised.
ISO 7752 consists of the following parts, under the general ti
...
SLOVENSKI STANDARD
SIST ISO 7752-3:2012
01-oktober-2012
1DGRPHãþD
SIST ISO 7752-3:1997
Žerjavi - Namestitev in karakteristike kontrolne opreme - 3. del: Stolpni žerjavi
Cranes - Control layout and characteristics - Part 3: Tower cranes
Appareils de levage à charge suspendue - Disposition et caractéristiques des
commandes - Partie 3: Grues à tour
Ta slovenski standard je istoveten z: ISO 7752-3:2010
ICS:
53.020.20 Dvigala Cranes
SIST ISO 7752-3:2012 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST ISO 7752-3:2012
---------------------- Page: 2 ----------------------
SIST ISO 7752-3:2012
INTERNATIONAL ISO
STANDARD 7752-3
Second edition
2010-06-01
Cranes — Control layout and
characteristics —
Part 3:
Tower cranes
Appareils de levage à charge suspendue — Disposition et
caractéristiques des commandes —
Partie 3: Grues à tour
Reference number
ISO 7752-3:2010(E)
©
ISO 2010
---------------------- Page: 3 ----------------------
SIST ISO 7752-3:2012
ISO 7752-3:2010(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
COPYRIGHT PROTECTED DOCUMENT
© ISO 2010
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2010 – All rights reserved
---------------------- Page: 4 ----------------------
SIST ISO 7752-3:2012
ISO 7752-3:2010(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the
...
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Žerjavi - Namestitev in karakteristike kontrolne opreme - 3. del: Stolpni žerjaviAppareils de levage à charge suspendue - Disposition et caractéristiques des commandes - Partie 3: Grues à tourCranes - Control layout and characteristics - Part 3: Tower cranes53.020.20DvigalaCranesICS:Ta slovenski standard je istoveten z:ISO 7752-3:2010oSIST ISO 7752-3:2012en,fr01-januar-2012oSIST ISO 7752-3:2012SLOVENSKI
STANDARD
oSIST ISO 7752-3:2012
Reference numberISO 7752-3:2010(E)© ISO 2010
INTERNATIONAL STANDARD ISO7752-3Second edition2010-06-01Cranes — Control layout and characteristics — Part 3: Tower cranes Appareils de levage à charge suspendue — Disposition et caractéristiques des commandes — Partie 3: Grues à tour
oSIST ISO 7752-3:2012
ISO 7752-3:2010(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
COPYRIGHT PROTECTED DOCUMENT
©
ISO 2010 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56 • CH-1211 Geneva 20 Tel.
+ 41 22 749 01 11 Fax
+ 41 22 749 09 47 E-mail
copyright@iso.org Web
www.iso.org Published in Switzerland
ii © ISO 2010 – All rights reserved
oSIST ISO 7752-3:2012
ISO 7752-3:2010(E) © ISO 2010 – All rights reserved iii Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of thi
...
NORME ISO
INTERNATIONALE 7752-3
Deuxième édition
2010-06-01
Appareils de levage à charge
suspendue — Disposition et
caractéristiques des commandes —
Partie 3:
Grues à tour
Cranes — Control layout and characteristics —
Part 3: Tower cranes
Numéro de référence
ISO 7752-3:2010(F)
©
ISO 2010
---------------------- Page: 1 ----------------------
ISO 7752-3:2010(F)
PDF – Exonération de responsabilité
Le présent fichier PDF peut contenir des polices de caractères intégrées. Conformément aux conditions de licence d'Adobe, ce fichier
peut être imprimé ou visualisé, mais ne doit pas être modifié à moins que l'ordinateur employé à cet effet ne bénéficie d'une licence
autorisant l'utilisation de ces polices et que celles-ci y soient installées. Lors du téléchargement de ce fichier, les parties concernées
acceptent de fait la responsabilité de ne pas enfreindre les conditions de licence d'Adobe. Le Secrétariat central de l'ISO décline toute
responsabilité en la matière.
Adobe est une marque déposée d'Adobe Systems Incorporated.
Les détails relatifs aux produits logiciels utilisés pour la création du présent fichier PDF sont disponibles dans la rubrique General Info
du fichier; les paramètres de création PDF ont été optimisés pour l'impression. Toutes les mesures ont été prises pour garantir
l'exploitation de ce fichier par les comités membres de l'ISO. Dans le cas peu probable où surviendrait un problème d'utilisation,
veuillez en informer le Secrétariat central à l'adresse donnée ci-dessous.
DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2010
Droits de reproduction réservés. Sauf prescription différente, aucune partie de cette publication ne peut être reproduite ni utilisée sous
quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie et les microfilms, sans l'accord écrit
de l'ISO à l'adresse ci-après ou du comité membre de l'ISO dans le pays du demandeur.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Publié en Suisse
ii © ISO 2010 – Tous droits réservés
---------------------- Page: 2 ----------------------
ISO 7752-3:2010(F)
Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes nationaux de
normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est en général confiée
aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude a le droit de faire partie du
comité technique créé à cet effet. Les organisations internationales, gouvernementales et non
gouvernementales, en liaison avec l'ISO participent également aux travaux. L'ISO collabore étroitement avec
la Commission électrotechnique internationale (CEI) en ce qui concerne la normalisation électrotechnique.
Les Normes internationales sont rédigées conformément aux règles données dans les Directives ISO/CEI,
Partie 2.
La tâche principale des comités techniques est d'élaborer les Normes internationales. Les projets de Normes
internationales adoptés par les comités techniques sont soumis aux comités membres pour vote. Leur
publication comme Normes internationales requiert l'approbation de 75 % au moins des comités membres
votants.
L'attention est appelée sur le fait que certains des éléments du présent document peuvent faire l'objet de
droits de propriété intellectuelle ou de droits analogues. L'ISO ne saurait être tenue pour responsable de ne
pas avoir identifié de tels droits de propriété et averti de leur existence.
L'ISO 7752-3 a été élaborée par le comité technique ISO/TC 96, Appareils de levage à charge suspendue,
sous-comité SC 7, Grues à tour.
Cette deuxième édition annule et remplace la première édition (ISO 7752-3:1993), qui a fait l'objet d'une
révision technique.
L'ISO 7752 comprend les parties suivantes, présentées sous le titre général Appareils de levage à charge
suspendue — Disposition et caractéristiques des commandes:
⎯ Partie 1: Principes généraux
⎯ Par
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.