Polyurethane tubing for use primarily in pneumatic installations — Dimensions and specification

ISO/TS 11619:2014 specifies the requirements for flexible thermoplastic polyurethane tubing conveying compressed air, for use in the ambient temperature range from 23 °C to 60 °C, in sizes from 3 mm to 12 mm outside diameter. Working pressure depends on the tube size and the service temperature. Tubing may be used with push on connectors which are specified in ISO 14743.

Tubes en polyuréthanne utilisés principalement dans les installations pneumatiques — Dimensions et spécifications

General Information

Status
Published
Publication Date
10-Feb-2014
Current Stage
9092 - International Standard to be revised
Completion Date
01-Feb-2021
Ref Project

Buy Standard

Technical specification
ISO/TS 11619:2014 - Polyurethane tubing for use primarily in pneumatic installations -- Dimensions and specification
English language
7 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

TECHNICAL ISO/TS
SPECIFICATION 11619
First edition
2014-02-15
Polyurethane tubing for use primarily
in pneumatic installations —
Dimensions and specification
Tubes en polyuréthanne utilisés principalement dans les installations
pneumatiques — Dimensions et spécifications
Reference number
ISO/TS 11619:2014(E)
©
ISO 2014

---------------------- Page: 1 ----------------------
ISO/TS 11619:2014(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2014
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2014 – All rights reserved

---------------------- Page: 2 ----------------------
ISO/TS 11619:2014(E)

Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Materials and construction . 1
5 Dimensions and tolerances . 1
5.1 Outside diameters, wall thickness and tolerances . 1
5.2 Length tolerances . 2
6 Performance requirements . 2
6.1 Hydrostatic testing at 23 °C ± 2 °C . 2
6.2 Hydrostatic testing at 60 °C ± 2 °C . 3
6.3 Maximum working pressure . 3
6.4 Minimum bend radius . 3
7 Type, routine and production testing . 4
8 Marking . 4
9 Recommendations for packing and storage . 4
Annex A (normative) Test frequency. 5
Annex B (informative) Recommended tests for production testing . 6
Bibliography . 7
© ISO 2014 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO/TS 11619:2014(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any
patent rights identified during the development of the document will be in the Introduction and/or on
the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical Barriers
to Trade (TBT) see the following URL: Foreword - Supplementary information
The committee responsible for this document is ISO/TC 45, Rubber and rubber products, Subcommittee
SC 1, Rubber and plastics hoses and hose assemblies.
iv © ISO 2014 – All rights reserved

---------------------- Page: 4 ----------------------
ISO/TS 11619:2014(E)

Introduction
This Technical Specification has been prepared to provide minimum acceptable requirements for the
satisfactory performance of thermoplastic polyurethane tubing used mainly in pneumatic applications.
The tubing conveys compressed air which controls and powers pneumatic systems.
This Technical Specification will be revised to an International Standard when ISO 14743 has been
revised and published in ISO/TC 131.
© ISO 2014 – All rights reserved v

---------------------- Page: 5 ----------------------
TECHNICAL SPECIFICATION ISO/TS 11619:2014(E)
Polyurethane tubing for use primarily in pneumatic
installations — Dimensions and specification
WARNING — Persons using this document should be familiar with normal laboratory practice.
This document does not purport to address all of the safety problems, if any, associated with its
use. It is the responsibility of the user to establish appropriate health and safety practices and to
ensure compliance with any national
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.