ISO 9692-2

Welding and allied processes — Joint preparation — Part 2: Submerged arc welding of steels

This part of IS0 9692 applies to types of joint preparation for submerged arc welding with one wire electrode (process 121 according to IS0 4063) on steel. This part of IS0 9692 covers only the welding positions PA and PB according to IS0 6947. In case PC is used, special preparation will be necessary. It applies to fully penetrated welds. For partly penetrated welds, types of joint preparation, shapes and dimensions may differ from the listed proposals if they are specified in the relevant application standard or agreed by parties concerned. If the root is welded by a different arc welding process (see IS0 40631, the joint preparation according to IS0 9692 should be taken into account.

Soudage et techniques connexes — Préparation de joints — Partie 2: Soudage à l'arc sous flux en poudre des aciers

La présente partie de I'ISO 9692 specific les types de préparation de joints pour soudage sous flux avec fil-electrode sur acier (procede 121 conformement a I'ISO 4063). La présente partie de I'ISO 9692 couvre seulement les positions de soudage PA et PB conformément a I'ISO 6947. Lorsque la position PC est utilisee, une preparation speciale doit etre adoptee. Elle est applicable aux soudures a pleine pénétration. Dans le cas de soudures a pénétration partielle, les types de preparation de joints, les formes et dimensions peuvent etre differents de ceux des exemples proposes ici s'ils sont specifies dans la norme d'application correspondante ou s'ils font I'objet d'un accord entre les parties concernees. Si la racine est soudee avec un procede de soudage different (voir IS0 4063), il est recommande que la preparation du joint conformement a I'ISO 9692 soit prise en compte.

General Information

• Status: Not Published
• ICS: 25.160.10 - Welding processes
• ICS: 25.160.40 - Welded joints and welds
• Technical Committee: ISO/TC 44/SC 7 - Representation and terms
• Drafting Committee: ISO/TC 44/SC 7 - Representation and terms
• Current Stage: 6000 - International Standard under publication
• Completion Date: 08-Dec-2023

Relations

• Revises: ISO 9692-2:1998 - Welding and allied processes — Joint preparation — Part 2: Submerged arc welding of steels
• Effective Date: 03-Dec-2022

Standards Content (Sample)

FINAL
INTERNATIONAL ISO/FDIS
DRAFT
STANDARD 9692-2
ISO/TC 44/SC 7
Welding and allied processes — Joint
Secretariat: BSI
preparation —
Voting begins on:
2023-09-13
Part 2:
Voting terminates on:
Submerged arc welding of steels
2023-12-06
Soudage et techniques connexes — Préparation de joints —
Partie 2: Soudage à l'arc sous flux en poudre des aciers
ISO/CEN PARALLEL PROCESSING
RECIPIENTS OF THIS DRAFT ARE INVITED TO
SUBMIT, WITH THEIR COMMENTS, NOTIFICATION
OF ANY RELEVANT PATENT RIGHTS OF WHICH
THEY ARE AWARE AND TO PROVIDE SUPPOR TING
DOCUMENTATION.
IN ADDITION TO THEIR EVALUATION AS
Reference number
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO-
ISO/FDIS 9692-2:2023(E)
LOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON
OCCASION HAVE TO BE CONSIDERED IN THE
LIGHT OF THEIR POTENTIAL TO BECOME STAN-
DARDS TO WHICH REFERENCE MAY BE MADE IN
NATIONAL REGULATIONS. © ISO 2023

---------------------- Page: 1 ----------------------
ISO/FDIS 9692-2:2023(E)
FINAL
INTERNATIONAL ISO/FDIS
DRAFT
STANDARD 9692-2
ISO/TC 44/SC 7
Welding and allied processes — Joint
Secretariat: BSI
preparation —
Voting begins on:
Part 2:
Voting terminates on:
Submerged arc welding of steels
Soudage et techniques connexes — Préparation de joints —
Partie 2: Soudage à l'arc sous flux en poudre des aciers
COPYRIGHT PROTECTED DOCUMENT
© ISO 2023
ISO/CEN PARALLEL PROCESSING
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
RECIPIENTS OF THIS DRAFT ARE INVITED TO
ISO copyright office
SUBMIT, WITH THEIR COMMENTS, NOTIFICATION
OF ANY RELEVANT PATENT RIGHTS OF WHICH
CP 401 • Ch. de Blandonnet 8
THEY ARE AWARE AND TO PROVIDE SUPPOR TING
CH-1214 Vernier, Geneva
DOCUMENTATION.
Phone: [phone]
IN ADDITION TO THEIR EVALUATION AS
Reference number
Email: [e-mail]
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO-
ISO/FDIS 9692-2:2023(E)
Website: www.iso.org
LOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON
Published in Switzerland
OCCASION HAVE TO BE CONSIDERED IN THE
LIGHT OF THEIR POTENTIAL TO BECOME STAN-
DARDS TO WHICH REFERENCE MAY BE MADE IN
ii
  © ISO 2023 – All rights reserved
NATIONAL REGULATIONS. © ISO 2023

---------------------- Page: 2 ----------------------
ISO/FDIS 9692-2:2023(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Materials . 1
5 Types of joint preparation . 1
Bibliography .10
iii
© ISO 2023 – All rights reserved

---------------------- Page: 3 ----------------------
ISO/FDIS 9692-2:2023(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that comm
...

ISO/FDIS 9692-2:2023(E)
ISO/TC 44/SC 7
Secretariat: BSI
Date: 2023-08-30
Welding and allied processes — Joint preparation —
Part 2:
Submerged arc welding of steels
Soudage et techniques connexes — Préparation de joints —
Partie 2: Soudage à l'arc sous flux en poudre des aciers
FDIS stage
© ISO 2023 – All rights reserved

---------------------- Page: 1 ----------------------
ISO/FDIS 9692-2:2023(E)
© ISO 2023
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this
publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical,
including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can
be requested from either ISO at the address below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: + 41 22 749 01 11
EmailE-mail: [e-mail]
Website: www.iso.org
Published in Switzerland
ii © ISO 2023 – All rights reserved

---------------------- Page: 2 ----------------------
ISO/FDIS 9692-2:2023(E)
Contents
Foreword . iv
Introduction . v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Materials . 1
5 Types of joint preparation . 1
Bibliography . 10

© ISO 2023 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO/FDIS 9692-2:2023(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO
collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documentsdocument should be noted. This document was drafted in accordance
with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawnISO draws attention to the possibility that some of the elementsimplementation of this
document may beinvolve the subjectuse of (a) patent(s). ISO takes no position concerning the evidence,
validity or applicability of any claimed patent rights in respect thereof. As of the date of publication of
this document, ISO had not received notice of (a) patent(s) which may be required to implement this
document. However, implementers are cautioned that this may not represent the latest information,
which may be obtained from the patent database available at www.iso.org/patents. ISO shall not be held
responsible for identifying any or all such patent rights. Details of any patent rights identified during the
development of the document will be in the Introduction and/or on the ISO list of patent declarations
received (see ).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as
...