Quality requirements for fusion welding of metallic materials - Part 1: Criteria for the selection of the appropriate level of quality requirements (ISO 3834-1:2005)

This part of ISO 3834 provides a general outline of ISO 3834 and criteria to be taken into account for the selection of the appropriate level of quality requirements for fusion welding of metallic materials, among the three levels specified in ISO 3834-2 [3], ISO 3834-3 [4] and ISO 3834-4 [5]. It applies to manufacturing, both in workshops and at field installation sites.

Qualitätsanforderungen für das Schmelzschweißen von metallischen Werkstoffen - Teil 1: Kriterien für die Auswahl der geeigneten Stufe der Qualitätsanforderungen (ISO 3834-1:2005)

Dieses Europäische Norm legt das Verfahren zur Klassifizierung der Feuerwiderstandsfähigkeit von Bauprodukten und Bauteilen fest, die als Teil von haustechnischen Anlagen in Gebäuden benutzt werden. Dabei werden die Ergebnisse von Feuerwiderstandsprüfungen benutzt, die innerhalb des direkten Anwendungsbereichs des entsprechenden Prüfverfahrens liegen. Eine Klassifizierung auf Grundlage des erweiterten Anwendungsbereichs ist nicht Bestandteil des Anwendungsbereichs dieser Europäischen Norm. Für den erweiterten Anwendungsbereich sind jedoch die gleichen Klassen zu verwenden, die in dieser Europäischen Norm festgelegt werden.
Bauprodukte/Bauteile zur Verwendung in Lüftungsanlagen (mit Ausnahme von Bauprodukten zur Rauch- und Wärmefreihaltung) beinhalten:
feuerwiderstandsfähige Leitungen;
Brandschutzklappen.
Relevante Prüfverfahren, die für diese Bauprodukte/-teile entwickelt wurden, sind in Abschnitt 2 aufgeführt.

Exigences de qualité en soudage par fusion des matériaux métalliques - Partie 1: Criteres pour la sélection du niveau approprié d'exigences de qualité (ISO 3834-1:2005)

L'ISO 3834-1:2005 fournit un aperçu général de l'ISO 3834 et les critères à prendre en compte pour la sélection d'un niveau approprié d'exigences de qualité en soudage par fusion des matériaux métalliques, parmi les trois niveaux spécifiés dans l'ISO 3834-2:2005, l'ISO 3834-3:2005 et l'ISO 3834-4:2005. Elle est applicable pour la fabrication aussi bien en atelier que sur les sites de montage.
L'ISO 3834-1:2005 ne spécifie pas d'exigences relatives à un système complet de management de la qualité. Cependant, les éléments d'un système de management de la qualité dont la prise en compte vient compléter l'ISO 3834 est défini.

Zahteve za kakovost pri talilnem varjenju kovinskih materialov – 1. del: Merila za izbiro stopenj sprejemljivosti (ISO 3834-1:2005)

General Information

Status
Withdrawn
Publication Date
28-Feb-2006
Withdrawal Date
03-Oct-2021
Technical Committee
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
27-Sep-2021
Due Date
20-Oct-2021
Completion Date
04-Oct-2021

Relations

Buy Standard

Standard
EN ISO 3834-1:2006 (EN)
English language
14 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Standard
EN ISO 3834-1:2006 (DE)
German language
10 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 3834-1:2006
01-marec-2006
1DGRPHãþD
SIST EN 729-1:1995
Zahteve za kakovost pri talilnem varjenju kovinskih materialov – 1. del: Merila za
izbiro stopenj sprejemljivosti (ISO 3834-1:2005)
Quality requirements for fusion welding of metallic materials - Part 1: Criteria for the
selection of the appropriate level of quality requirements (ISO 3834-1:2005)
Qualitätsanforderungen für das Schmelzschweißen von metallischen Werkstoffen - Teil
1: Kriterien für die Auswahl der geeigneten Stufe der Qualitätsanforderungen (ISO 3834-
1:2005)
Exigences de qualité en soudage par fusion des matériaux métalliques - Partie 1:
Criteres pour la sélection du niveau approprié d'exigences de qualité (ISO 3834-1:2005)
Ta slovenski standard je istoveten z: EN ISO 3834-1:2005
ICS:
03.120.99 Drugi standardi v zvezi s Other standards related to
kakovostjo quality
25.160.10 Varilni postopki in varjenje Welding processes
SIST EN ISO 3834-1:2006 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 3834-1:2006

---------------------- Page: 2 ----------------------

SIST EN ISO 3834-1:2006


EUROPEAN STANDARD EN ISO 3834-1

NORME EUROPÉENNE

EUROPÄISCHE NORM
December 2005
ICS 25.160.01 Supersedes EN 729-1:1994
English Version
Quality requirements for fusion welding of metallic materials -
Part 1: Criteria for the selection of the appropriate level of quality
requirements (ISO 3834-1:2005)
Exigences de qualité en soudage par fusion des matériaux Qualitätsanforderungen für das Schmelzschweißen von
métalliques - Partie 1: Critères pour la sélection du niveau metallischen Werkstoffen - Teil 1: Kriterien für die Auswahl
approprié d'exigences de qualité (ISO 3834-1:2005) der geeigneten Stufe der Qualitätsanforderungen (ISO
3834-1:2005)
This European Standard was approved by CEN on 28 October 2005.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.

CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.






EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2005 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 3834-1:2005: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 3834-1:2006

EN ISO 3834-1:2005 (E)





Foreword


This document (EN ISO 3834-1:2005) has been prepared by Technical Committee ISO/TC 44
"Welding and allied processes" in collaboration with Technical Committee CEN/TC 121
"Welding", the secretariat of which is held by DIN.

This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by June 2006, and conflicting national
standards shall be withdrawn at the latest by June 2006.

This document supersedes EN 729-1:1994.

According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary,
Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.


Endorsement notice

The text of ISO 3834-1:2005 has been approved by CEN as EN ISO 3834-1:2005 without any
modifications.

2

---------------------- Page: 4 ----------------------

SIST EN ISO 3834-1:2006

INTERNATIONAL ISO
STANDARD 3834-1
Second edition
2005-12-15


Quality requirements for fusion welding
of metallic materials —
Part 1:
Criteria for the selection of the
appropriate level of quality requirements
Exigences de qualité en soudage par fusion des matériaux
métalliques —
Partie 1: Critères pour la sélection du niveau approprié d'exigences de
qualité





Reference number
ISO 3834-1:2005(E)
©
ISO 2005

---------------------- Page: 5 ----------------------

SIST EN ISO 3834-1:2006
ISO 3834-1:2005(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


©  ISO 2005
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland

ii © ISO 2005 – All rights reserved

---------------------- Page: 6 ----------------------

SIST EN ISO 3834-1:2006
ISO 3834-1:2005(E)
Contents Page
Foreword. iv
Introduction . v
1 Scope. 1
2 Normative references. 1
3 Terms and definitions. 1
4 General outline of ISO 3834 . 2
5 Selection of quality requirements. 3
6 Elements to be considered for a quality management system to complement ISO 3834. 4
Annex A (informative) Criteria which assist in the selection of the appropriate part of ISO 3834 . 5
Bibliography . 7

© ISO 2005 – All rights reserved iii

---------------------- Page: 7 ----------------------

SIST EN ISO 3834-1:2006
ISO 3834-1:2005(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 3834-1 was prepared by Technical Committee ISO/TC 44, Welding and allied processes, Subcommittee
SC 10, Unification of requirements in the fiel of metal welding.
This second edition cancels and replaces the first edition (ISO 3834-1:1994), which has been technically
revised.
ISO 3834 consists of the following parts, under the general title Quality requirements for fusion welding of
metallic materials:
⎯ Part 1: Criteria for the selection of the appropriate level of quality requirements
⎯ Part 2: Comprehensive quality requirements
⎯ Part 3: Standard quality requirements
⎯ Part 4: Elementary quality requirements
⎯ Part 5: Documents with which it is necessary to conform to claim conformity to the quality requirements of
ISO 3834-2, ISO 3834-3 or ISO 3834-4
NOTE A Technical Report ISO/TR 3834-6, Quality requirements for fusion welding of metallic materials — Part 6:
Guidance on implementing ISO 3834 is being prepared.
Requests for official interpretations of any aspect of this part of ISO 3834 should be directed to the Secretariat
of ISO/TC 44/SC 10 via your national standards body, a complete listing which can be found at
http://www.iso.org.
iv © ISO 2005 – All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 3834-1:2006
ISO 3834-1:2005(E)
Introduction
Processes such as fusion welding are widely used to manufacture many products. In some companies, they
are the key feature of production. Products may range from simple to complex. Examples include pressure
vessels, domestic and agricultural equipment, cranes, bridges, transport vehicles and other items.
These processes exert a profound influence on the cost of manufacture and quality of the product. It is
important, therefore, to ensure that these processes are carried out in the most effective way and that
appropriate control is exercised over all aspects of the operation.
It is emphasised that ISO 3834 is not a quality management system standard replacing ISO 9001:2000.
However, it can be a useful tool when ISO 9001:2000 is applied by manufacturers.
Specification of quality requirements for welding processes is important because the quality of these
processes cannot be readily verified. Therefore, they are considered to be special processes as noted by
ISO 9000:2000.
Quality cannot be inspected into a product, it has to be built in. Even the most extensive and sophisticated
non-destructive testing does not improve the quality of the product.
For products to be free from serious problems in production and in service, it is necessary to provide controls,
from the design phase, through material selection, into manufacture and subsequent inspection. For example,
poor design may create serious and costly difficulties in the workshop, on site, or in service. Incorrect material
selection may result in problems, such as cracking in welded joints.
To ensure sound and effective manufacturing, management needs to understand and appreciate the sources
of potential trouble and to implement appropriate procedures for their control.
ISO 3834 identifies me
...

SLOVENSKI STANDARD
SIST EN ISO 3834-1:2006
01-marec-2006
1DGRPHãþD
SIST EN 729-1:1995
Zahteve za kakovost pri talilnem varjenju kovinskih materialov – 1. del: Merila za
izbiro stopenj sprejemljivosti (ISO 3834-1:2005)
Quality requirements for fusion welding of metallic materials - Part 1: Criteria for the
selection of the appropriate level of quality requirements (ISO 3834-1:2005)
Qualitätsanforderungen für das Schmelzschweißen von metallischen Werkstoffen - Teil
1: Kriterien für die Auswahl der geeigneten Stufe der Qualitätsanforderungen (ISO 3834-
1:2005)
Exigences de qualité en soudage par fusion des matériaux métalliques - Partie 1:
Criteres pour la sélection du niveau approprié d'exigences de qualité (ISO 3834-1:2005)
Ta slovenski standard je istoveten z: EN ISO 3834-1:2005
ICS:
03.120.99 Drugi standardi v zvezi s Other standards related to
kakovostjo quality
25.160.10 Varilni postopki in varjenje Welding processes
SIST EN ISO 3834-1:2006 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 3834-1:2006

---------------------- Page: 2 ----------------------

SIST EN ISO 3834-1:2006


EUROPÄISCHE NORM EN ISO 3834-1

EUROPEAN STANDARD

NORME EUROPÉENNE
Dezember 2005
ICS 25.160.01 Ersatz für EN 729-1:1994
Deutsche Fassung
Qualitätsanforderungen für das Schmelzschweißen von
metallischen Werkstoffen - Teil 1: Kriterien für die Auswahl der
geeigneten Stufe der Qualitätsanforderungen (ISO 3834-1:2005)
Quality requirements for fusion welding of metallic materials Exigences de qualité en soudage par fusion des matériaux
- Part 1: Criteria for the selection of the appropriate level of métalliques - Partie 1: Critères pour la sélection du niveau
quality requirements (ISO 3834-1:2005) approprié d'exigences de qualité (ISO 3834-1:2005)
Diese Europäische Norm wurde vom CEN am 28.Oktober 2005 angenommen.

Die CEN-Mitglieder sind gehalten, die CEN/CENELEC-Geschäftsordnung zu erfüllen, in der die Bedingungen festgelegt sind, unter denen
dieser Europäischen Norm ohne jede Änderung der Status einer nationalen Norm zu geben ist. Auf dem letzen Stand befindliche Listen
dieser nationalen Normen mit ihren bibliographischen Angaben sind beim Management-Zentrum oder bei jedem CEN-Mitglied auf Anfrage
erhältlich.

Diese Europäische Norm besteht in drei offiziellen Fassungen (Deutsch, Englisch, Französisch). Eine Fassung in einer anderen Sprache,
die von einem CEN-Mitglied in eigener Verantwortung durch Übersetzung in seine Landessprache gemacht und dem Zentralsekretariat
mitgeteilt worden ist, hat den gleichen Status wie die offiziellen Fassungen.

CEN-Mitglieder sind die nationalen Normungsinstitute von Belgien, Dänemark, Deutschland, Estland, Finnland, Frankreich, Griechenland,
Irland, Island, Italien, Lettland, Litauen, Luxemburg, Malta, den Niederlanden, Norwegen, Österreich, Polen, Portugal, Schweden, der
Schweiz, der Slowakei, Slowenien, Spanien, der Tschechischen Republik, Ungarn, dem Vereinigten Königreich und Zypern.






EUROPÄISCHES KOMITEE FÜR NORMUNG
EUROPEAN COMMITTEE FOR STANDARDIZATION

COMITÉ EUROPÉEN DE NORMALISATION

Management-Zentrum: rue de Stassart, 36  B-1050 Brüssel
© 2005 CEN Alle Rechte der Verwertung, gleich in welcher Form und in welchem Ref. Nr. EN ISO 3834-1:2005 D
Verfahren, sind weltweit den nationalen Mitgliedern von CEN vorbehalten.

---------------------- Page: 3 ----------------------

SIST EN ISO 3834-1:2006
EN ISO 3834-1:2005 (D)
Inhalt
Seite
Vorwort .3
Einleitung.4
1 Anwendungsbereich .5
2 Normative Verweisungen.5
3 Begriffe .5
4 Allgemeine Auslegung von ISO 3834 .6
5 Auswahl der geeigneten Stufe der Qualitätsanforderungen.7
6 Zu berücksichtigende Elemente zur Ergänzung von ISO 3834 zu einem
Qualitätsmanagementsystem.7
Anhang A (informativ) Kriterien für die Auswahl von ISO 3834-2, ISO 3834-3 und ISO 3834-4 .8
Literaturhinweise .10

2

---------------------- Page: 4 ----------------------

SIST EN ISO 3834-1:2006
EN ISO 3834-1:2005 (D)
Vorwort
Dieses Dokument (EN ISO 3834-1:2005) wurde vom Technischen Komitee ISO/TC 44 „Welding and allied
processes“ in Zusammenarbeit mit dem Technischen Komitee CEN/TC 121 „Schweißen“ erarbeitet, dessen
Sekretariat vom DIN gehalten wird.
Diese Europäische Norm muss den Status einer nationalen Norm erhalten, entweder durch Veröffentlichung
eines identischen Textes oder durch Anerkennung bis Juni 2006, und etwaige entgegenstehende nationale
Normen müssen bis Juni 2006 zurückgezogen werden.
Dieses Dokument ersetzt EN 729-1:1994.
Entsprechend der CEN/CENELEC-Geschäftsordnung sind die nationalen Normungsinstitute der folgenden
Länder gehalten, diese Europäische Norm zu übernehmen: Belgien, Dänemark, Deutschland, Estland,
Finnland, Frankreich, Griechenland, Irland, Island, Italien, Lettland, Litauen, Luxemburg, Malta, Niederlande,
Norwegen, Österreich, Polen, Portugal, Schweden, Schweiz, Slowakei, Slowenien, Spanien, Tschechische
Republik, Ungarn, Vereinigtes Königreich und Zypern.
Anerkennungsnotiz
Der Text von ISO 3834-1:2005 wurde vom CEN als EN ISO 3834-1:2005 ohne irgendeine Abänderung
genehmigt.
ISO 3834 Qualitätsanforderungen für das Schmelzschweißen von metallischen Werkstoffen besteht aus:
⎯ Teil 1: Kriterien für die Auswahl der geeigneten Stufe der Qualitätsanforderungen
⎯ Teil 2: Umfassende Qualitätsanforderungen
⎯ Teil 3: Standard-Qualitätsanforderungen
⎯ Teil 4: Elementare Qualitätsanforderungen
⎯ Teil 5: Dokumente, deren Anforderungen erfüllt werden müssen, um die Übereinstimmung mit den
Anforderungen nach ISO 3834-2, ISO 3834-3 oder ISO 3834-4 nachzuweisen
ANMERKUNG Ein Technischer Bericht ISO/TR 3834-6, Qualitätsanforderungen für das Schmelzschweißen von
metallischen Werkstoffen — Teil 6: Leitfaden für die Einführung von ISO 3834, wird vorbereitet.
Anfragen zur offiziellen Auslegung der Inhalte dieser Norm sollten über das jeweilige nationale
Normungsinstitut an das Sekretariat des ISO/TC 44/SC 10 gerichtet werden. Eine vollständige Auflistung kann
über www.iso.org bezogen werden.
3

---------------------- Page: 5 ----------------------

SIST EN ISO 3834-1:2006
EN ISO 3834-1:2005 (D)
Einleitung
Prozesse wie Schmelzschweißen werden im großen Umfang eingesetzt, um viele Produkte herzustellen. In
einigen Firmen nehmen sie eine Schlüsselstellung in der Fertigung ein. Die Produkte können im Bereich
einfach bis komplex liegen. Beispiele sind: Druckbehälter, Haushalts- und Agrargeräte, Krane, Brücken,
Transportfahrzeuge und andere Gegenstände.
Diese Prozesse üben einen entscheidenden Einfluss auf die Herstellkosten und die Qualität des Erzeugnisses
aus. Daher ist es wichtig, sicherzustellen, dass diese Prozesse in der effektivsten Weise ausgeführt werden
und dass für alle Vorgänge geeignete Überwachungen vorgesehen werden.
Es wird darauf hingewiesen, dass ISO 3834 keine Norm für ein Qualitätsmanagementsystem ist, die
ISO 9001:2000 ersetzt. Sie kann aber ein hilfreiches Werkzeug sein, wenn ISO 9001:2000 vom Hersteller
angewendet wird.
Die Spezifizierung der Qualitätsanforderungen für Schweißprozesse ist wichtig, weil die Qualität dieser
Prozesse nicht ohne weiteres verifiziert werden kann. Deshalb werden sie als spezielle Prozesse bezeichnet,
siehe ISO 9000:2000.
Qualität kann nicht in ein Erzeugnis hineingeprüft, sondern muss in ihm erzeugt werden. Selbst die umfas-
sendste und höchstentwickelte zerstörungsfreie Prüfung verbessert nicht die Qualität der Schweißungen.
Für Produkte, die frei von ernsthaften Problemen bei der Herstellung und beim Einsatz sein müssen, ist es
notwendig, vom Konstruktionsstadium über die Werkstoffauswahl bis zur Herstellung und der nachfolgenden
Prüfung Kontrollen vorzusehen. Zum Beispiel kann eine schlechte Konstruktion ernsthafte und kostenträchtige
Schwierigkeiten in der Werkstatt, auf der Baustelle oder während des Einsatzes hervorrufen. Eine falsche
Werkstoffauswahl kann zu Problemen, z. B. zu Rissen in Schweißverbindungen, führen.
Um eine vernünftige und erfolgreiche Herstellung sicherzustellen, muss das Management die Quellen
möglicher Schwierigkeiten erkennen und geeignete Verfahren für ihre Kontrollen einführen.
ISO 3834 nennt Maßnahmen für verschiedene Situationen. Übliche Anwendungen dieser Normen sind
folgende Fälle:
⎯ bei Vertragsverhandlungen: Festlegungen der schweißtechnischen Qualitätsanforderungen;
⎯ für Hersteller: Einführung und Aufrechterhaltung der schweißtechnischen Qualitätsanforderungen;
⎯ für Ausschüsse, die Bauvorschriften oder Anwendungsnormen vorbereiten: Festlegung der schweißtech-
nischen Qualitätsanforderungen;
⎯ für Organisationen, die die Qualitätsausführung bewerten, z. B. unabhängige Prüfstellen, Kunden oder
Hersteller.
ISO 3834 kann von internen und externen Organisationen, eingeschlossen Zertifizierungsstellen, benutzt
werden, um die Fähigkeit des Herstellers zu bewerten, die Anforderungen des Kunden, gesetzliche
Bestimmungen oder die eigenen Anforderungen des Herstellers zu erfüllen.
4

---------------------- Page: 6 ----------------------

SIST EN ISO 3834-1:2006
EN ISO 3834-1:2005 (D)
1 Anwendungsbereich
Dieser Teil von ISO 3834 beschreibt die allgemeine Auslegung von ISO 3834 und die zu beachtenden
Kriterien für die Auswahl der geeigneten Stufe der Qualitätsanforderungen für das Schmelzschweißen von
metallischen Werkstoffen, aus den drei festgelegten Stufen in ISO 3834-2 [3], ISO 3834-3 [4] und ISO 3834-4
[5]. Er gilt für die Herstellung, sowohl in Werkstätten als auch auf Baustellen.
ANMERKUNG 1 ISO 3834-2, ISO 3834-3 und ISO 3834-4 enthalten komplette Sätze von Qualitätsanforderungen zur
Prozesskontrolle für alle Schmelzschweißprozesse (für einen einzelnen Prozess oder in einer festgelegten Kombination).
ISO 3834-5 legt die Dokumente fest, deren Anforderungen erfüllt werden müssen, um die Übereinstimmung mit den
Qualitätsanforderungen nach ISO 3834-2, ISO 3834-3 oder ISO 3834-4 nachzuweisen.
Dieser Teil von ISO 3834 legt keine Anforderungen für ein Qualitätsmanagementsystem fest. Aber Abschnitt 6
enthält Elemente eines Qualitätsmanagementsystems, deren Einschluss ISO 3834 ergänzt.
ANMERKUNG 2 ISO 3834-2, ISO 3834-3 und ISO 3834-4 dürfen für sich allein oder in Verbindung mit ISO 90
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.