SIST EN ISO 8666:2018
(Main)Small craft - Principal data (ISO 8666:2016)
Small craft - Principal data (ISO 8666:2016)
ISO 8666:2016 establishes definitions of main dimensions and related data and of mass specifications and loading conditions. It applies to small craft having a length of the hull (LH) of up to 24 m.
Kleine Wasserfahrzeuge - Hauptdaten (ISO 8666:2016)
Petits navires - Données principales (ISO 8666:2016)
L'ISO 8666 :2016 établit les définitions des dimensions principales et des caractéristiques qui leur sont associées ainsi que les définitions des spécifications de masse et des conditions de chargement. Elle s'applique aux petits navires d'une longueur de coque (LH) inférieure ou égale à 24 m.
Mala plovila - Osnovni podatki (ISO 8666:2016)
ISO 8666:2016 vsebuje opredelitve glavnih dimenzij s povezanimi podatki in specifikacij mase s pogoji obremenitve. Uporablja se za mala plovila z dolžino trupa (LH) do 24 m.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 8666:2018
01-december-2018
1DGRPHãþD
SIST EN ISO 8666:2016
Mala plovila - Osnovni podatki (ISO 8666:2016)
Small craft - Principal data (ISO 8666:2016)
Kleine Wasserfahrzeuge - Hauptdaten (ISO 8666:2016)
Petits navires - Données principales (ISO 8666:2016)
Ta slovenski standard je istoveten z: EN ISO 8666:2018
ICS:
47.080 ýROQL Small craft
SIST EN ISO 8666:2018 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 8666:2018
---------------------- Page: 2 ----------------------
SIST EN ISO 8666:2018
EN ISO 8666
EUROPEAN STANDARD
NORME EUROPÉENNE
October 2018
EUROPÄISCHE NORM
ICS 47.080 Supersedes EN ISO 8666:2016
English Version
Small craft - Principal data (ISO 8666:2016)
Petits navires - Données principales (ISO 8666:2016) Kleine Wasserfahrzeuge - Hauptdaten (ISO 8666:2016)
This European Standard was approved by CEN on 16 April 2018.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 8666:2018 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 8666:2018
EN ISO 8666:2018 (E)
Contents Page
European foreword . 3
Annex ZA (informative) Relationship between this European Standard and the Essential
Requirements of Directive 2013/53/EU aimed to be covered . 4
2
---------------------- Page: 4 ----------------------
SIST EN ISO 8666:2018
EN ISO 8666:2018 (E)
European foreword
The text of ISO 8666:2016 has been prepared by Technical Committee ISO/TC 188 “Small craft” of the
International Organization for Standardization (ISO) and has been taken over as EN ISO 8666:2018.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by April 2019, and conflicting national standards shall be
withdrawn at the latest by April 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 8666:2016.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive 2013/53/EU.
For relationship with EU Directive 2013/53/EU, see informative Annex ZA, which is an integral part of
this document.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia,
Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands,
Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
the United Kingdom.
Endorsement notice
The text of ISO 8666:2016 has been approved by CEN as EN ISO 8666:2018 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 8666:2018
EN ISO 8666:2018 (E)
Annex ZA
(informative)
Relationship between this European Standard and the Essential
Requirements of Directive 2013/53/EU aimed to be covered
This European standard has been prepared under a Commission’s standardization request M/542
C(2015) 8736 final to provide one voluntary means of conforming to Essential Requirements of Directive
2013/53/EU.
Once this standard is cited in the Official Journal of the European Union under that Directive, compliance
with the normative clauses of this standard given in Table ZA.1 confers, within the limits of the scope of
this standard, a presumption of conformity with the corresponding Essential Requirements of that
Directive and associated EFTA regulations.
Table ZA.1 — Correspondence between this European Standard and Article 3 and Annex I of
Directive 2013/53/EU
Essential Requirements of Clause(s)/sub- Remarks/Notes
Directive 2013/53/EU clause(s) of
this EN
Article 3(10) – Definitions - 4.2.1, 4.2.3, 7.3 - ‘Hull length’ means the length of hull measured
‘Hull length’ in accordance with the harmonised standard.
This standard establishes the methodology for
measuring the length of hull L .
H
Annex I, Part A, 2 GENERAL
REQUIREMENTS
Annex I, Part A, 2.2 (d) – 5.6 The Standard establishes the definition for
Watercraft builder’s plate “maximum load m ”. This is to be understood
ML
as the “manufacturer's recommended maximum
load” in accordance with EN ISO 14946.
Annex I, Part A, 3 INTEGRITY
AND STRUCTURAL
REQUIREMENTS
Annex I, Part A, 3.1 - Structure 2, 3, 4, 5, 6, 7 This Standard establishes definitions for main
dimensions and related data, mass
specifications and loading conditions that are
required for determining hull construction and
scantlings derived from EN ISO 12215.
Annex I, Part A, 3.2 - Stability 2, 3, 4, 5, 6, 7 This Standard establishes definitions for main
and freeboard dimensions and related data, mass
specifications and loading conditions that are
required for evaluating the stability and
buoyancy of intact (i.e. undamaged) boats in
accordance with EN ISO 12217 in order to
4
---------------------- Page: 6 ----------------------
SIST EN ISO 8666:2018
EN ISO 8666:2018 (E)
assign a design category appropriate to the
design and maximum load.
Annex I, Part A, 3.3 – Buoyancy 2, 3, 4, 5, 6, 7 This Standard establishes definitions for main
and floatation dimensions and related data, mass
specifications and loading conditions that are
required for evaluating the flotation
characteristics of boats susceptible to swamping
and the requirements for inverted buoyancy in
accordance with EN ISO 12217.
Annex I, Part A, 3.4 - Flooding 4.2.3, 4.3.2, In respect of dimensions for calculating the
4.4.3.3 cockpit volume coefficient in accordance with
EN ISO 12216.
Annex I, Part A, 3.6 - 5.6 The Standard establishes the definition for
Manufacturer’s maximum “maximum load m ”. This is to be understood
ML
recommended load as the “manufacturer's recommended maximum
load” in accordance with EN ISO 14946.
Annex I, Part A, 5
INSTALLATION
REQUIREMENTS
Annex I, Part A, 5.4.2 – Steering 2.8, 2.9 The Standard establishes definitions for a
systems -Emergency “sailing craft” and a “non-sailing craft”.
arrangements for sailing
These definitions shall be used wherever
recreational craft and single-
required for the application of the essential
propulsion engine non-sailing
requirements set out in Annex I of Directive
recreational craft
2013/53/EU.
WARNING 1 — Presumption of conformity stays valid only as long as a reference to this European
Standard is maintained in the list published in the Official Journal of the European Union. Users of this
standard should consult frequently the latest list published in the Official Journal of the European Union.
WARNING 2 — Other Union legislation may be applicable to the product(s) falling within the scope of
this standard.
5
---------------------- Page: 7 ----------------------
SIST EN ISO 8666:2018
---------------------- Page: 8 ----------------------
SIST EN ISO 8666:2018
INTERNATIONAL ISO
STANDARD 8666
Second edition
2016-07-01
Small craft — Principal data
Petits navires — Données principales
Reference number
ISO 8666:2016(E)
©
ISO 2016
---------------------- Page: 9 ----------------------
SIST EN ISO 8666:2018
ISO 8666:2016(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2016, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2016 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 8666:2018
ISO 8666:2016(E)
Contents Page
Foreword .v
1 Scope . 1
2 Terms and definitions . 1
3 Symbols, designations and units . 2
4 Measurements . 3
4.1 General . 3
4.2 Longitudinal . 4
4.2.1 General. 4
4.2.2 Maximum length, L .
max 4
4.2.3 Length of the hull, L .
H 4
4.2.4 Waterline length, L .
WL 7
4.3 Athwartship . 8
4.3.1 General. 8
4.3.2 Maximum beam, B .
max 8
4.3.3 Beam of hull, B .
H 8
4.3.4 Beam, waterline, B .
WL 8
4.3.5 Maximum beam, waterline, B .
WLmax 8
4.3.6 Beam between hull centers, B .
CB 8
4.4 Vertical . 9
4.4.1 Maximum depth, D .
max 9
4.4.2 Midship depth, D .
LWL/2 9
4.4.3 Freeboard, F .10
4.4.4 Draught, T .10
4.4.5 Draught, air, H .
a 10
4.4.6 Headroom .11
4.5 Other data .11
4.5.1 Deadrise angle, β . .11
4.5.2 Reference sail area, A .
S 12
4.5.3 Standard sail area, A’ .
S 12
4.5.4 Windage area, A .
lv 12
4.5.5 Volume of the craft, V .12
5 Masses.13
5.1 Mass, net shipping, m .
N 13
5.2 Mass, gross shipping, m .
G 13
5.3 Mass, light craft, m .
LC 14
5.3.1 Items of equipment included in m .
LC 14
5.3.2 Items of equipment and other items not included in m .
LC 15
5.4 Performance test mass, m .
P 15
5.5 Mass of the craft when towed on a trailer, m .
T 16
5.5.1 General.16
5.5.2 Items of equipment included in m .
T 16
5.5.3 Items of equipment not included in m .
T 18
5.5.4 Exclusions, inclusions .18
5.6 Maximum load, m .
ML 18
6 Loading conditions .19
6.1 Test condition .19
6.2 Ready-for-use condition.19
6.3 Fully loaded ready-for-use condition .19
6.4 Empty craft condition .19
6.5 Light craft condition .20
6.6 Minimum operating condition.21
6.7 Loaded arrival condition .21
© ISO 2016 – All rights reserved iii
---------------------- Page: 11 ----------------------
SIST EN ISO 8666:2018
ISO 8666:2016(E)
6.8 Maximum load condition .21
7 Tolerances .21
7.1 Published data .21
7.2 Preliminary specification .22
7.3 Reference lengths .22
Bibliography .23
iv © ISO 2016 – All rights reserved
---------------------- Page: 12 ----------------------
SIST EN ISO 8666:2018
ISO 8666:2016(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical
Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information
The committee responsible for this document is ISO/TC 188, Small craft.
This second edition cancels and replaces the first edition (ISO 8666:2002), which has been technically
revised with the following main changes:
— definitions 2.7 to 2.13 have been added;
— list of symbols in Table 1 has been extended;
— 4.3.5 and 4.3.6 have been added;
— 4.5.2, 4.5.3 and 4.5.4 have been added, and “projected sail area” has been deleted;
— 6.4 to 6.8 have been added;
— 7.1 has been modified and 7.3 added;
— clause on owner’s manual has been deleted.
© ISO 2016 – All rights reserved v
---------------------- Page: 13 ----------------------
SIST EN ISO 8666:2018
---------------------- Page: 14 ----------------------
SIST EN ISO 8666:2018
INTERNATIONAL STANDARD ISO 8666:2016(E)
Small craft — Principal data
1 Scope
This International Standard establishes definitions of main dimensions and related data and of mass
specifications and loading conditions. It applies to small craft having a length of the hull (L ) of up to 24 m.
H
2 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
NOTE For units, see Clause 3.
2.1
waterline
WL
intersection line of the water’s surface with the craft’s hull when the craft (2.13) is afloat
2.2
maximum load waterline
reference waterline
WL
ref
waterline (2.1) of the craft (2.13) when upright in the maximum loaded displacement (2.5.1)
2.3
sheerline
intersection between deck and hull, for rounded deck edges the natural intersection, or, where no deck
is fitted or the hull extends above the deck (bulwark), the upper edge of the craft’s hull
Note 1 to entry: The upper position of the sheerline depends on the inclination between the hull/deck intersection
and the actual deck.
2.4
transom beam
B
T
maximum width of the hull at the transom at or below the sheerline (2.3), excluding extensions, handles
and fittings
Note 1 to entry: Where spray rails act as chines or part of the planing surface, they are included in the transom
beam measurement.
Note 2 to entry: For craft (2.13) with a rounded or pointed stern or with a transom beam of less than half the
maximum beam of the craft, the transom beam, B , is the widest beam at or below the sheerline at the aft quarter
T
length of the hull.
2.5
displacement
mass of water displaced by the craft (2.13), including all appendages
2.5.1
loaded displacement
m
LDC
mass of water displaced by the craft (2.13), including all appendages, when in the fully loaded ready-
for-use condition
Note 1 to entry: Fully loaded ready-for use condition is described in 6.3.
© ISO 2016 – All rights reserved 1
---------------------- Page: 15 ----------------------
SIST EN ISO 8666:2018
ISO 8666:2016(E)
2.5.2
displacement volume
V
D
volume of water displaced by the craft (2.13) that corresponds to the displacement (2.5)
Note 1 to entry: Where the density of water used to calculate the volume of displacement is not salt water at a
3
density of 1 025 kg/m , the density of water used to calculate the volume of displacement is specified.
2.6
tank capacity
net usable volume of the tank(s) for the craft (2.13) in design trim (2.11) at rest at the maximum load
waterline (2.2)
2.7
wing mast
spar characterized by its cross-section which shows a smooth transition at the aft end into the sail,
thus, contributing to its driving force
2.8
non-sailing boat
craft (2.13) for which the primary means of propulsion is other than by wind power, having reference
2/3
sail area (2.10) (A ) < 0,07 (m )
S LDC
2.9
sailing boat
craft (2.13) for which the primary means of propulsion is by wind power, having reference sail area
2/3
(2.10) (A ) ≥ 0,07 (m )
S LDC
2.10
reference sail area
A
S
actual profile area of sails set abaft a mast, plus the maximum profile areas of all masts, plus reference
triangle area(s) forward of each mast
2.11
design trim
longitudinal attitude of the craft (2.13) when upright, with crew, fluids, stores, and equipment in the
position(s) and load condition(s) designated by the designer or builder
2.12
underway
not at anchor, or made fast to the shore, or aground
2.13
craft
small craft
recreational boat, and other watercraft using similar equipment, of up to 24 m length of hull (L )
H
3 Symbols, designations and units
Unless specifically otherwise defined, the symbols, designations and units used in this International
Standard are given in Table 1.
Table 1 — Symbols, designations and units
Symbol Designation Unit Clause
2
A Windage area m 4.5.4
lV
2
A Reference sail area m 4.5.2
S
2
A’ Standard sail area m 4.5.3
S
2 © ISO 2016 – All rights reserved
---------------------- Page: 16 ----------------------
SIST EN ISO 8666:2018
ISO 8666:2016(E)
Table 1 (continued)
Symbol Designation Unit Clause
B Beam between hull centers m 4.3.6
CB
B Beam of hull m 4.3.3
H
B Maximum beam m 4.3.2
max
B Beam, waterline m 4.3.4
WL
B Maximum beam, waterline m 4.3.5
WLmax
B Transom beam m 2.4
T
D Maximum depth m 4.4.1
max
D Midship depth m 4.4.2
LWL/2
F Freeboard m 4.4.3
F Freeboard, aft m 4.4.3.2
A
F Freeboard, forward m 4.4.3.4
F
F Freeboard, amidships m 4.4.3.3
M
H Draught, air m 4.4.5
a
L Length of the hull m 4.2.3
H
L Maximum length m 4.2.2
max
L Waterline length m 4.2.4
WL
m Gross shipping mass kg 5.2
G
m Loaded displacement kg 2.5.1
LDC
m Light craft mass kg 5.3
LC
m Net shipping mass kg 5.1
N
m Performance test mass kg 5.4
P
m Mass of craft when towed on trailer kg 5.5
T
m Maximum load kg 5.6
ML
T Draught m 4.4.4
T Draught, canoe body m 4.4.4.4
C
T Draught, maximum m 4.4.4.2
max
T Draught, minimum m 4.4.4.3
min
3
V Displacement volume m 2.5.2
D
3
V Volume of the craft m 4.5.5
3
V Volume of the hull m 4.5.5.2
H
3
V Volume of the superstructure m 4.5.5.3
S
WL Waterline 2.1
WL Maximum load waterline 2.2
ref
β Deadrise angle degrees 4.5.1
4 Measurements
4.1 General
Measurements shall be established with the craft at rest at the maximum load waterline/reference
waterline, WL , unless otherwise stated.
ref
© ISO 2016 – All rights reserved 3
---------------------- Page: 17 ----------------------
SIST EN ISO 8666:2018
ISO 8666:2016(E)
4.2 Longitudinal
4.2.1 General
The lengths of a craft shall be measured parallel to the maximum load waterline/reference waterline
and craft centreline as the distance between two vertical planes, perpendicular to the centreplane of
the craft.
4.2.2 Maximum length, L
max
The maximum length (L ) shall be measured in accordance with 4.2.1, one plane tangent through the
max
foremost part and the other through the aftermost part of the craft.
This length includes all structural and integral parts of the craft, such as stems or sterns, bulwarks, and
hull/deck joints.
This length includes parts which are normally fixed, such as fixed spars, bowsprits, pulpits at either
end of the craft,
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.