SIST ISO 12151-1:2014
Connections for hydraulic fluid power and general use - Hose fittings - Part 1: Hose fittings with ISO 8434-3 O-ring face seal ends
Connections for hydraulic fluid power and general use - Hose fittings - Part 1: Hose fittings with ISO 8434-3 O-ring face seal ends
This part of ISO 12151 specifies the general and dimensional requirements for the design and performance of hose fittings with O-ring face seal ends in accordance with ISO 8434-3, made of carbon steel, for nominal hose inside diameters of 6,3 mm to 38 mm, inclusive, in accordance with ISO 4397. These hose fittings (see Figure 1 for a typical example) are for use in hydraulic fluid power systems with hose that meets the requirements of the respective hose standards and in general applications with suitable hose.
Raccordements pour transmissions hydrauliques et applications générales -- Raccords de flexible -- Partie 1: Raccords de flexible avec embouts à joints faciaux toriques conformes à l'ISO 8434-3
L'ISO 12151-1:2010 sp�cifie les exigences g�n�rales et dimensionnelles pour la conception et les performances des raccords de flexible avec embouts � joints faciaux toriques, en acier au carbone conformes � l'ISO 8434‑3, dont le diam�tre int�rieur nominal est compris entre 6,3 mm et 38 mm inclus en conformit� avec l'ISO 4397.
D'autres mat�riaux peuvent �tre utilis�s apr�s accord entre le fabricant et l'utilisateur.
Ces raccords de flexible sont destin�s � �tre utilis�s dans les syst�mes de transmissions hydrauliques avec des tuyaux qui r�pondent aux exigences des normes de tuyaux respectives, et dans des applications g�n�rales lorsqu'il s'agit de tuyaux adapt�s.
Fluidna tehnika - Hidravlika - Spoji za hidravliko in za splošno uporabo - Cevne armature - 1. del: Cevne armature s tesnilko O po ISO 8434-3
General Information
Relations
Buy Standard
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 12151-1
Second edition
2010-06-15
Connections for hydraulic fluid power
and general use — Hose fittings —
Part 1:
Hose fittings with ISO 8434-3 O-ring face
seal ends
Raccordements pour transmissions hydrauliques et applications
générales — Raccords de flexible —
Partie 1: Raccords de flexible avec embouts à joints faciaux toriques
conformes à l'ISO 8434-3
Reference number
ISO 12151-1:2010(E)
©
ISO 2010
---------------------- Page: 1 ----------------------
ISO 12151-1:2010(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
COPYRIGHT PROTECTED DOCUMENT
© ISO 2010
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2010 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 12151-1:2010(E)
Contents Page
Foreword .iv
Introduction.v
1 Scope.1
2 Normative references.2
3 Terms and definitions .2
4 Performance requirements.2
5 Designation of hose fittings .3
6 Design.3
7 Manufacture .4
8 Assembly instructions.4
9 Procurement information.5
10 Marking.5
11 Identification statement (reference to this part of ISO 12151) .5
Annex A (informative) Illustrations of applications for short, medium and long
ISO 12151-1 hose fittings.14
Bibliography.15
© ISO 2010 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO 12151-1:2010(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 12151-1 was prepared by Technical Committee ISO/TC 131, Fluid power systems, Subcommittee SC 4,
Connectors and similar products and components.
This second edition cancels and replaces the first edition (ISO 12151-1:1999), which has been technically
revised.
ISO 12151 consists of the following parts, under the general title Connections for hydraulic fluid power and
general use — Hose fittings:
⎯ Part 1: Hose fittings with ISO 8434-3 O-ring face seal ends
⎯ Part 2: Hose fittings with ISO 8434-1 and ISO 8434-4 24° cone connector ends with O-rings
⎯ Part 3: Hose fittings with ISO 6162-1 or ISO 6162-2 flange ends
⎯ Part 4: Hose fittings with ISO 6149 metric stud ends
⎯ Part 5: Hose fittings with ISO 8434-2 37° flared ends
⎯ Part 6: Hose fittings with ISO 8434-6 60° cone ends
iv © ISO 2010 – All rights reserved
---------------------- Page: 4 ----------------------
ISO 12151-1:2010(E)
Introduction
In hydraulic fluid power systems, power is transmitted and controlled through a liquid under pressure within an
enclosed circuit. In general applications, the fluid can be conveyed under pressure.
Components are connected through their ports by stud ends on fluid conductor connectors to tubes/pipes or to
hose fittings and hoses.
© ISO 2010 – All rights reserved v
---------------------- Page: 5 ----------------------
INTERNATIONAL STANDARD ISO 12151-1:2010(E)
Connections for hydraulic fluid power and general use — Hose
fittings —
Part 1:
Hose fittings with ISO 8434-3 O-ring face seal ends
1 Scope
This part of ISO 12151 specifies the general and dimensional requirements for the design and performance of
hose fittings with O-ring face seal ends in accordance with ISO 8434-3, made of carbon steel, for nominal
hose inside diameters of 6,3 mm to 38 mm, inclusive, in accordance with ISO 4397.
NOTE 1 Materials other than carbon steel can be supplied as agreed between the manufacturer and user.
NOTE 2 For hose fittings used in hydraulic and pneumatic braking systems on road vehicles (as defined in the scope of
ISO/TC 22, Road vehicles), see ISO 4038, ISO 4039-1 and ISO 4039-2.
These hose fittings (see Figure 1 for a typical example) are for use in hydraulic fluid power systems with hose
that meets the requirements of the respective hose standards and in general applications with suitable hose.
Key
1 hose fitting 4 adapter in accordance with ISO 8434-3
2 port in accordance with ISO 6149-1 5 nut
3 O-ring seal 6 O-ring seal
Figure 1 — Typical example of a hose-fitting connection with O-ring face seal end
© ISO 2010 – All rights reserved 1
---------------------- Page: 6 ----------------------
ISO 12151-1:2010(E)
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 68-2, ISO general-purpose screw threads –– Basic profile –– Part 2: Inch screw threads
ISO 263, ISO inch screw threads –– General plan and selection for screws, bolts and nuts –– Diameter range
0,06 to 6 in
ISO 4397, Fluid power systems and components –– Connectors and associated components –– Nominal
outside diameters of tubes and nominal hose sizes
ISO 4759-1:2000, Tolerances for fasteners –– Part 1: Bolts, screws, studs and nuts –– Product grades A, B
and C
ISO 5598, Fluid power systems and components –– Vocabulary
ISO 5864:1993, ISO inch screw threads –– Allowances and tolerances
ISO 6149-1, Connections for hydraulic fluid power and general use –– Ports and stud ends with ISO 261
metric threads and O-ring sealing –– Part 1: Ports with truncated housing for O-ring seal
ISO 6605, Hydraulic fluid power — Hoses and hose assemblies — Test methods
ISO 8434-3:2005, Metallic tube connections for fluid power and general use –– Part 3: O-ring face seal
connectors
ISO 9227, Corrosion tests in artificial atmospheres –– Salt spray tests
ISO 19879, Metallic tube connections for fluid power and general use — Test methods for hydraulic fluid
power connections
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 5598 apply.
4 Performance requirements
4.1 Hose assemblies shall meet the performance requirements specified in the appropriate hose
specification without leakage or failure.
4.2 The working pressure of the hose assembly shall be the lower of the pressures given for its size in
ISO 8434-3 and in the relevant hose specification.
4.3 The hose-fitting portion of a hose assembly shall be tested in accordance with ISO 19879, and the
complete hose assembly shall be tested in accordance with ISO 6605.
2 © ISO 2010 – All rights reserved
---------------------- Page: 7 ----------------------
ISO 12151-1:2010(E)
5 Designation of hose fittings
5.1 Hose fittings shall be designated by an alphanumeric code to facilitate ordering. They shall be
designated by ISO 12151-1, followed by a spaced hyphen, then the connection end type, shape and style
letter symbols (see 5.4), followed by another spaced hyphen, the O-ring face seal end size (nominal tube
outside diameter in accordance with ISO 8434-3) and the hose size (nominal hose inside diameter in
4397), each separated by a multiplication symbol (×).
accordance with ISO
EXAMPLE A swivel hose fitting with a 45° medium elbow, for 12 mm OD tubing and 12,5 mm nominal ID hose is
designated as follows:
ISO 12151-1 - SWE45M - 12 × 12,5
5.2 The letter symbol designation of the hose fitting shall consist of the connection end type, immediately
followed by the shape of the fitting and the nut style, where applicable.
5.3 Tube ends are assumed to be male and thus it is not necessary to include them in the code. However, if
another end is involved, it shall be designated.
5.4 The letter symbols as given in Table 1 shall be used.
Table 1 — Letter symbols used in the designation of hose fittings
Connection end type Symbol
Swivel — SW
Shape Straight S
90° elbow, short ES
90° elbow, medium EM
90° elbow, long EL
45° elbow, short E45S
45° elbow, medium E45M
Nut sealing surface Sealing surface not exposed A
Sealing surface exposed B
6 Design
6.1 Hose fitting dimensions shown in Figures 2 to 5 shall conform to those given in Tables 2 to 5 and to the
relevant dimensions in ISO 8434-3.
6.2 Hexagonal tolerances across flats shall be in accordance with ISO 4759-1:2000, product grade C.
Minimum across-corner hexagonal dimensions are 1,092 times the nominal width across flats. The minimum
side flat is 0,43 times the nominal width across flats.
6.3 Angular tolerances on axes of ends of elbows shall be ±3° for all sizes.
6.4 Details of contour shall be as chosen by the manufacturer, provided that the dimensions given in
Tables 2 to 5 are maintained.
6.5 The screw threads on the connection ends of the hose fittings shall be ISO inch screw threads in
accordance with ISO 263 and ISO 8434-3:2005, Annex A, except for 1-14 UNS classes 2A and 2B threads,
whose dimensions are also found in ISO 8434-3:2005, Annex A.
© ISO 2010 – All rights reserved 3
---------------------- Page: 8 ----------------------
ISO 12151-1:2010(E)
7 Manufacture
7.1 Construction
Hose fittings may be made by forging or cold forming, machined from barstock or manufactured from multiple
components.
7.2 Workmanship
Workmanship shall conform to the best commercial practice to produce high-quality hose fittings. Hose fittings
shall be free from visual contaminants, all hanging burrs, loose scale and slivers that can be dislodged in use,
and any other defects that can affect the functioning of the parts. All machined surfaces shall have a surface
roughness value of Ra u 6,3 µm, except where otherwise specified.
7.3 Finish
The external surface and threads of all carbon steel parts shall be plated or coated with a suitable material
that passes a 72 h neutral salt-spray test in accordance with ISO 9227, unless otherwise agreed upon by the
manufacturer and the user. Any appearance of red rust during the salt-spray test on any area, except those
noted below, shall be considered failure:
⎯ all internal fluid passages;
⎯ edges, such as hex points, serrations and crests of threads, where there can be mechanical deformation
of the plating or coating typical of mass-produced
...
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Fluidna tehnika - Hidravlika - Spoji za hidravliko in za splošno uporabo - Cevne armature - 1. del: Cevne armature s tesnilko O po ISO 8434-3Raccordements pour transmissions hydrauliques et applications générales -- Raccords de flexible -- Partie 1: Raccords de flexible avec embouts à joints faciaux toriques conformes à l'ISO 8434-3Connections for hydraulic fluid power and general use - Hose fittings - Part 1: Hose fittings with ISO 8434-3 O-ring face seal ends23.100.40Cevna napeljava in sklopkePiping and couplings23.040.70Gumene cevi in armatureHoses and hose assembliesICS:Ta slovenski standard je istoveten z:ISO 12151-1:2010oSIST ISO 12151-1:2014en,fr01-januar-2014oSIST ISO 12151-1:2014SLOVENSKI
STANDARD
oSIST ISO 12151-1:2014
Reference numberISO 12151-1:2010(E)© ISO 2010
INTERNATIONAL STANDARD ISO12151-1Second edition2010-06-15Connections for hydraulic fluid power and general use — Hose fittings — Part 1: Hose fittings with ISO 8434-3 O-ring face seal ends Raccordements pour transmissions hydrauliques et applications générales — Raccords de flexible —
Partie 1: Raccords de flexible avec embouts à joints faciaux toriques conformes à l'ISO 8434-3 oSIST ISO 12151-1:2014
ISO 12151-1:2010(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
COPYRIGHT PROTECTED DOCUMENT
©
ISO 2010 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56 • CH-1211 Geneva 20 Tel.
+ 41 22 749 01 11 Fax
+ 41 22 749 09 47 E-mail
copyright@iso.org Web
www.iso.org Published in Switzerland
ii
© ISO 2010 – All rights reserved
oSIST ISO 12151-1:2014
ISO 12151-1:2010(E) © ISO 2010 – All rights reserved
iii Contents Page Foreword.iv Introduction.v 1 Scope.1 2 Normative references.2 3 Terms and definitions.2 4 Performance requirements.2 5 Designation of hose fittings.3 6 Design.3 7 Manufacture.4 8 Assembly instructions.4 9 Procurement information.5 10 Marking.5 11 Identification statement (reference to this part of ISO 12151).5 Annex A (informative)
Illustrations of applications for short, medium and long ISO 12151-1 hose fittings.14 Bibliography.15
oSIST ISO 12151-1:2014
ISO 12151-1:2010(E) iv
© ISO 2010 – All rights reserved Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 12151-1 was prepared by Technical Committee ISO/TC 131, Fluid power systems, Subcommittee SC 4, Connectors and similar products and components. This second edition cancels and replaces the first edition (ISO 12151-1:1999), which has been technically revised. ISO 12151 consists of the following parts, under the general title Connections for hydraulic fluid power and general use — Hose fittings: ⎯ Part 1: Hose fittings with ISO 8434-3 O-ring face seal ends ⎯ Part 2: Hose fittings with ISO 8434-1 and ISO 8434-4 24° cone connector ends with O-rings ⎯ Part 3: Hose fittings with ISO 6162-1 or ISO 6162-2 flange ends ⎯ Part 4: Hose fittings with ISO 6149 metric stud ends ⎯ Part 5: Hose fittings with ISO 8434-2 37° flared ends ⎯ Part 6: Hose fittings with ISO 8434-6 60° cone ends
oSIST ISO 12151-1:2014
ISO 12151-1:2010(E) © ISO 2010 – All rights reserved
v Introduction In hydraulic fluid power systems, power is transmitted and controlled through a liquid under pressure within an enclosed circuit. In general applications, the fluid can be conveyed under pressure. Components are connected through their ports by stud ends on fluid conductor connectors to tubes/pipes or to hose fittings and hoses.
oSIST ISO 12151-1:2014
oSIST ISO 12151-1:2014
INTERNATIONAL STANDARD ISO 12151-1:2010(E) © ISO 2010 – All rights reserved
1 Connections for hydraulic fluid power and general use — Hose fittings — Part 1: Hose fittings with ISO 8434-3 O-ring face seal ends 1 Scope This part of ISO 12151 specifies the general and dimensional requirements for the design and performance of hose fittings with O-ring face seal ends in accordance with ISO 8434-3, made of carbon steel, for nominal hose inside diameters of 6,3 mm to 38 mm, inclusive, in accordance with ISO 4397. NOTE 1 Materials other than carbon steel can be supplied as agreed between the manufacturer and user. NOTE 2 For hose fittings used in hydraulic and pneumatic braking systems on road vehicles (as defined in the scope of ISO/TC 22, Road vehicles), see ISO 4038, ISO 4039-1 and ISO 4039-2. These hose fittings (see Figure 1 for a typical example) are for use in hydraulic fluid power systems with hose that meets the requirements of the respective hose standards and in general applications with suitable hose.
Key 1 hose fitting 4 adapter in accordance with ISO 8434-3 2 port in accordance with ISO 6149-1 5 nut 3 O-ring seal 6 O-ring seal Figure 1 — Typical example of a hose-fitting connection with O-ring face seal end oSIST ISO 12151-1:2014
ISO 12151-1:2010(E) 2
© ISO 2010 – All rights reserved 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 68-2, ISO general-purpose screw threads –– Basic profile –– Part 2: Inch screw threads ISO 263, ISO inch screw threads –– General plan and selection for screws, bolts and nuts –– Diameter range 0,06 to 6 in ISO 4397, Fluid power systems and components –– Connectors and associated components –– Nominal outside diameters of tubes and nominal hose sizes ISO 4759-1:2000, Tolerances for fasteners –– Part 1: Bolts, screws, studs and nuts –– Product grades A, B and C ISO 5598, Fluid power systems and components –– Vocabulary ISO 5864:1993, ISO inch screw threads –– Allowances and tolerances ISO 6149-1, Connections for hydraulic fluid power and general use –– Ports and stud ends with ISO 261 metric threads and O-ring sealing –– Part 1: Ports with truncated housing for O-ring seal ISO 6605, Hydraulic fluid power — Hoses and hose assemblies — Test methods ISO 8434-3:2005, Metallic tube connections for fluid power and general use –– Part 3: O-ring face seal connectors ISO 9227, Corrosion tests in artificial atmospheres –– Salt spray tests ISO 19879, Metallic tube connections for fluid power and general use — Test methods for hydraulic fluid power connections 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 5598 apply. 4 Performance requirements 4.1 Hose assemblies shall meet the performance requirements specified in the appropriate hose specification without leakage or failure. 4.2 The working pressure of the hose assembly shall be the lower of the pressures given for its size in ISO 8434-3 and in the relevant hose specification. 4.3 The hose-fitting portion of a hose assembly shall be tested in accordance with ISO 19879, and the complete hose assembly shall be tested in accordance with ISO 6605. oSIST ISO 12151-1:2014
ISO 12151-1:2010(E) © ISO 2010 – All rights reserved
3 5 Designation of hose fittings 5.1 Hose fittings shall be designated by an alphanumeric code to facilitate ordering. They shall be designated by ISO 12151-1, followed by a spaced hyphen, then the connection end type, shape and style letter symbols (see 5.4), followed by another spaced hyphen, the O-ring face seal end size (nominal tube outside diameter in accordance with ISO 8434-3) and the hose size (nominal hose inside diameter in accordance with ISO 4397), each separated by a multiplication symbol (×). EXAMPLE A swivel hose fitting with a 45° medium elbow, for 12 mm OD tubing and 12,5 mm nominal ID hose is designated as follows: ISO 12151-1 - SWE45M - 12 × 12,5 5.2 The letter symbol designation of the hose fitting shall consist of the connection end type, immediately followed by the shape of the fitting and the nut style, where applicable. 5.3 Tube ends are assumed to be male and thus it is not necessary to include them in the code. However, if another end is involved, it shall be designated. 5.4 The letter symbols as given in Table 1 shall be used. Table 1 — Letter symbols used in the designation of hose fittings Connection end type Symbol Swivel — SW Straight S 90° elbow, short ES 90° elbow, medium EM 90° elbow, long EL 45° elbow, short E45S Shape 45° elbow, medium E45M Sealing surface not exposed A Nut sealing surface Sealing surface exposed B 6 Design 6.1 Hose fitting dimensions shown in Figures 2 to 5 shall conform to those given in Tables 2 to 5 and to the relevant dimensions in ISO 8434-3. 6.2 Hexagonal tolerances across flats shall be in accordance with ISO 4759-1:2000, product grade C. Minimum across-corner hexagonal dimensions are 1,092 times the nominal width across flats. The minimum side flat is 0,43 times the nominal width across flats. 6.3 Angular tolerances on axes of ends of elbows shall be ±3° for all sizes. 6.4 Details of contour shall be as chosen by the manufacturer, provided that the dimensions given in Tables 2 to 5 are maintained. 6.5 The screw threads on the connection ends of the hose fittings shall be ISO inch screw threads in accordance with ISO 263 and ISO 8434-3:2005, Annex A, except for 1-14 UNS classes 2A and 2B threads, whose dimensions are also found in ISO 8434-3:2005, Annex A. oSIST ISO 12151-1:2014
ISO 12151-1:2010(E) 4
© ISO 2010 – All rights reserved 7 Manufacture 7.1 Construction Hose fittings may be made by forging or cold forming, machined from barstock or manufactured from multiple components. 7.2 Workmanship Workmanship shall conform to the best commercial practice to produce high-quality hose fittings. Hose fittings shall be free from visual contaminants, all hanging burrs, loose scale and slivers that can be dislodged in use, and
...
SLOVENSKI STANDARD
SIST ISO 12151-1:2014
01-marec-2014
1DGRPHãþD
SIST ISO 12151-1:2000
Fluidna tehnika - Hidravlika - Spoji za hidravliko in za splošno uporabo - Cevne
armature - 1. del: Cevne armature s tesnilko O po ISO 8434-3
Connections for hydraulic fluid power and general use - Hose fittings - Part 1: Hose
fittings with ISO 8434-3 O-ring face seal ends
Raccordements pour transmissions hydrauliques et applications générales -- Raccords
de flexible -- Partie 1: Raccords de flexible avec embouts à joints faciaux toriques
conformes à l'ISO 8434-3
Ta slovenski standard je istoveten z: ISO 12151-1:2010
ICS:
23.040.70 Gumene cevi in armature Hoses and hose assemblies
23.100.40 Cevna napeljava in sklopke Piping and couplings
SIST ISO 12151-1:2014 en,fr
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST ISO 12151-1:2014
---------------------- Page: 2 ----------------------
SIST ISO 12151-1:2014
INTERNATIONAL ISO
STANDARD 12151-1
Second edition
2010-06-15
Connections for hydraulic fluid power
and general use — Hose fittings —
Part 1:
Hose fittings with ISO 8434-3 O-ring face
seal ends
Raccordements pour transmissions hydrauliques et applications
générales — Raccords de flexible —
Partie 1: Raccords de flexible avec embouts à joints faciaux toriques
conformes à l'ISO 8434-3
Reference number
ISO 12151-1:2010(E)
©
ISO 2010
---------------------- Page: 3 ----------------------
SIST ISO 12151-1:2014
ISO 12151-1:2010(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
COPYRIGHT PROTECTED DOCUMENT
© ISO 2010
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2010 – All rights reserved
---------------------- Page: 4 ----------------------
SIST ISO 12151-1:2014
ISO 12151-1:2010(E)
Contents Page
Foreword .iv
Introduction.v
1 Scope.1
2 Normative references.2
3 Terms and definitions .2
4 Performance requirements.2
5 Designation of hose fittings .3
6 Design.3
7 Manufacture .4
8 Assembly instructions.4
9 Procurement information.5
10 Marking.5
11 Identification statement (reference to this part of ISO 12151) .5
Annex A (informative) Illustrations of applications for short, medium and long
ISO 12151-1 hose fittings.14
Bibliography.15
© ISO 2010 – All rights reserved iii
---------------------- Page: 5 ----------------------
SIST ISO 12151-1:2014
ISO 12151-1:2010(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 12151-1 was prepared by Technical Committee ISO/TC 131, Fluid power systems, Subcommittee SC 4,
Connectors and similar products and components.
This second edition cancels and replaces the first edition (ISO 12151-1:1999), which has been technically
revised.
ISO 12151 consists of the following parts, under the general title Connections for hydraulic fluid power and
general use — Hose fittings:
⎯ Part 1: Hose fittings with ISO 8434-3 O-ring face seal ends
⎯ Part 2: Hose fittings with ISO 8434-1 and ISO 8434-4 24° cone connector ends with O-rings
⎯ Part 3: Hose fittings with ISO 6162-1 or ISO 6162-2 flange ends
⎯ Part 4: Hose fittings with ISO 6149 metric stud ends
⎯ Part 5: Hose fittings with ISO 8434-2 37° flared ends
⎯ Part 6: Hose fittings with ISO 8434-6 60° cone ends
iv © ISO 2010 – All rights reserved
---------------------- Page: 6 ----------------------
SIST ISO 12151-1:2014
ISO 12151-1:2010(E)
Introduction
In hydraulic fluid power systems, power is transmitted and controlled through a liquid under pressure within an
enclosed circuit. In general applications, the fluid can be conveyed under pressure.
Components are connected through their ports by stud ends on fluid conductor connectors to tubes/pipes or to
hose fittings and hoses.
© ISO 2010 – All rights reserved v
---------------------- Page: 7 ----------------------
SIST ISO 12151-1:2014
---------------------- Page: 8 ----------------------
SIST ISO 12151-1:2014
INTERNATIONAL STANDARD ISO 12151-1:2010(E)
Connections for hydraulic fluid power and general use — Hose
fittings —
Part 1:
Hose fittings with ISO 8434-3 O-ring face seal ends
1 Scope
This part of ISO 12151 specifies the general and dimensional requirements for the design and performance of
hose fittings with O-ring face seal ends in accordance with ISO 8434-3, made of carbon steel, for nominal
hose inside diameters of 6,3 mm to 38 mm, inclusive, in accordance with ISO 4397.
NOTE 1 Materials other than carbon steel can be supplied as agreed between the manufacturer and user.
NOTE 2 For hose fittings used in hydraulic and pneumatic braking systems on road vehicles (as defined in the scope of
ISO/TC 22, Road vehicles), see ISO 4038, ISO 4039-1 and ISO 4039-2.
These hose fittings (see Figure 1 for a typical example) are for use in hydraulic fluid power systems with hose
that meets the requirements of the respective hose standards and in general applications with suitable hose.
Key
1 hose fitting 4 adapter in accordance with ISO 8434-3
2 port in accordance with ISO 6149-1 5 nut
3 O-ring seal 6 O-ring seal
Figure 1 — Typical example of a hose-fitting connection with O-ring face seal end
© ISO 2010 – All rights reserved 1
---------------------- Page: 9 ----------------------
SIST ISO 12151-1:2014
ISO 12151-1:2010(E)
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 68-2, ISO general-purpose screw threads –– Basic profile –– Part 2: Inch screw threads
ISO 263, ISO inch screw threads –– General plan and selection for screws, bolts and nuts –– Diameter range
0,06 to 6 in
ISO 4397, Fluid power systems and components –– Connectors and associated components –– Nominal
outside diameters of tubes and nominal hose sizes
ISO 4759-1:2000, Tolerances for fasteners –– Part 1: Bolts, screws, studs and nuts –– Product grades A, B
and C
ISO 5598, Fluid power systems and components –– Vocabulary
ISO 5864:1993, ISO inch screw threads –– Allowances and tolerances
ISO 6149-1, Connections for hydraulic fluid power and general use –– Ports and stud ends with ISO 261
metric threads and O-ring sealing –– Part 1: Ports with truncated housing for O-ring seal
ISO 6605, Hydraulic fluid power — Hoses and hose assemblies — Test methods
ISO 8434-3:2005, Metallic tube connections for fluid power and general use –– Part 3: O-ring face seal
connectors
ISO 9227, Corrosion tests in artificial atmospheres –– Salt spray tests
ISO 19879, Metallic tube connections for fluid power and general use — Test methods for hydraulic fluid
power connections
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 5598 apply.
4 Performance requirements
4.1 Hose assemblies shall meet the performance requirements specified in the appropriate hose
specification without leakage or failure.
4.2 The working pressure of the hose assembly shall be the lower of the pressures given for its size in
ISO 8434-3 and in the relevant hose specification.
4.3 The hose-fitting portion of a hose assembly shall be tested in accordance with ISO 19879, and the
complete hose assembly shall be tested in accordance with ISO 6605.
2 © ISO 2010 – All rights reserved
---------------------- Page: 10 ----------------------
SIST ISO 12151-1:2014
ISO 12151-1:2010(E)
5 Designation of hose fittings
5.1 Hose fittings shall be designated by an alphanumeric code to facilitate ordering. They shall be
designated by ISO 12151-1, followed by a spaced hyphen, then the connection end type, shape and style
letter symbols (see 5.4), followed by another spaced hyphen, the O-ring face seal end size (nominal tube
outside diameter in accordance with ISO 8434-3) and the hose size (nominal hose inside diameter in
4397), each separated by a multiplication symbol (×).
accordance with ISO
EXAMPLE A swivel hose fitting with a 45° medium elbow, for 12 mm OD tubing and 12,5 mm nominal ID hose is
designated as follows:
ISO 12151-1 - SWE45M - 12 × 12,5
5.2 The letter symbol designation of the hose fitting shall consist of the connection end type, immediately
followed by the shape of the fitting and the nut style, where applicable.
5.3 Tube ends are assumed to be male and thus it is not necessary to include them in the code. However, if
another end is involved, it shall be designated.
5.4 The letter symbols as given in Table 1 shall be used.
Table 1 — Letter symbols used in the designation of hose fittings
Connection end type Symbol
Swivel — SW
Shape Straight S
90° elbow, short ES
90° elbow, medium EM
90° elbow, long EL
45° elbow, short E45S
45° elbow, medium E45M
Nut sealing surface Sealing surface not exposed A
Sealing surface exposed B
6 Design
6.1 Hose fitting dimensions shown in Figures 2 to 5 shall conform to those given in Tables 2 to 5 and to the
relevant dimensions in ISO 8434-3.
6.2 Hexagonal tolerances across flats shall be in accordance with ISO 4759-1:2000, product grade C.
Minimum across-corner hexagonal dimensions are 1,092 times the nominal width across flats. The minimum
side flat is 0,43 times the nominal width across flats.
6.3 Angular tolerances on axes of ends of elbows shall be ±3° for all sizes.
6.4 Details of contour shall be as chosen by the manufacturer, provided that the dimensions given in
Tables 2 to 5 are maintained.
6.5 The screw threads on the connection ends of the hose fittings shall be ISO inch screw threads in
accordance with ISO 263 and ISO 8434-3:2005, Annex A, except for 1-14 UNS classes 2A and 2B threads,
whose dimensions are also found in ISO 8434-3:2005, Annex A.
© ISO 2010 – All rights reserved 3
---------------------- Page: 11 ----------------------
SIST ISO 12151-1:2014
ISO 12151-1:2010(E)
7 Manufacture
7.1 Construction
Hose fittings may be made by forging or cold forming, machined from barstock or manufactured from multiple
components.
7.2 Workmanship
Workmanship shall conform to the best commercial practice to produce high-quality hose fittings. Hose fittings
shall be free from visual contaminants, all hanging burrs, loose scale and slivers that can be dislodged in use,
and any other defects that can affect the functioning of the parts. All machined surfaces shall have a surface
roughness value of Ra u 6,3
...
NORME ISO
INTERNATIONALE 12151-1
Deuxième édition
2010-06-15
Raccordements pour transmissions
hydrauliques et applications générales —
Raccords de flexible —
Partie 1:
Raccords de flexible avec embouts
à joints faciaux toriques conformes
à l'ISO 8434-3
Connections for hydraulic fluid power and general use — Hose
fittings —
Part 1: Hose fittings with ISO 8434-3 O-ring face seal ends
Numéro de référence
ISO 12151-1:2010(F)
©
ISO 2010
---------------------- Page: 1 ----------------------
ISO 12151-1:2010(F)
PDF – Exonération de responsabilité
Le présent fichier PDF peut contenir des polices de caractères intégrées. Conformément aux conditions de licence d'Adobe, ce fichier
peut être imprimé ou visualisé, mais ne doit pas être modifié à moins que l'ordinateur employé à cet effet ne bénéficie d'une licence
autorisant l'utilisation de ces polices et que celles-ci y soient installées. Lors du téléchargement de ce fichier, les parties concernées
acceptent de fait la responsabilité de ne pas enfreindre les conditions de licence d'Adobe. Le Secrétariat central de l'ISO décline toute
responsabilité en la matière.
Adobe est une marque déposée d'Adobe Systems Incorporated.
Les détails relatifs aux produits logiciels utilisés pour la création du présent fichier PDF sont disponibles dans la rubrique General Info
du fichier; les paramètres de création PDF ont été optimisés pour l'impression. Toutes les mesures ont été prises pour garantir
l'exploitation de ce fichier par les comités membres de l'ISO. Dans le cas peu probable où surviendrait un problème d'utilisation,
veuillez en informer le Secrétariat central à l'adresse donnée ci-dessous.
DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2010
Droits de reproduction réservés. Sauf prescription différente, aucune partie de cette publication ne peut être reproduite ni utilisée sous
quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie et les microfilms, sans l'accord écrit
de l'ISO à l'adresse ci-après ou du comité membre de l'ISO dans le pays du demandeur.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Publié en Suisse
ii © ISO 2010 – Tous droits réservés
---------------------- Page: 2 ----------------------
ISO 12151-1:2010(F)
Sommaire Page
Avant-propos .iv
Introduction.v
1 Domaine d'application .1
2 Références normatives.2
3 Termes et définitions .2
4 Exigences relatives aux performances .2
5 Désignation des flexibles de raccordement .2
6 Conception.3
7 Fabrication .4
8 Instructions de montage.5
9 Informations à fournir à l'achat.5
10 Marquage.5
11 Phrase d'identification (référence à la présente partie de l'ISO 12151).5
Annexe A (informative) Illustrations d'applications pour raccord de flexible ISO 12151-1 court,
moyen et long .14
Bibliographie.15
© ISO 2010 – Tous droits réservés iii
---------------------- Page: 3 ----------------------
ISO 12151-1:2010(F)
Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes nationaux de
normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est en général confiée
aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude a le droit de faire partie du
comité technique créé à cet effet. Les organisations internationales, gouvernementales et non
gouvernementales, en liaison avec l'ISO participent également aux travaux. L'ISO collabore étroitement avec
la Commission électrotechnique internationale (CEI) en ce qui concerne la normalisation électrotechnique.
Les Normes internationales sont rédigées conformément aux règles données dans les Directives ISO/CEI,
Partie 2.
La tâche principale des comités techniques est d'élaborer les Normes internationales. Les projets de Normes
internationales adoptés par les comités techniques sont soumis aux comités membres pour vote. Leur
publication comme Normes internationales requiert l'approbation de 75 % au moins des comités membres
votants.
L'attention est appelée sur le fait que certains des éléments du présent document peuvent faire l'objet de
droits de propriété intellectuelle ou de droits analogues. L'ISO ne saurait être tenue pour responsable de ne
pas avoir identifié de tels droits de propriété et averti de leur existence.
L'ISO 12151-1 a été élaborée par le comité technique ISO/TC 131, Transmissions hydrauliques et
pneumatiques, sous-comité SC 4, Raccords, produits similaires et leurs composants.
Cette deuxième édition annule et remplace la première édition (ISO 12151-1:1999), qui a fait l'objet d'une
révision technique.
L'ISO 12151 comprend les parties suivantes, présentées sous le titre général Raccordements pour
transmissions hydrauliques et applications générales — Raccords de flexible:
⎯ Partie 1: Raccords de flexible avec embouts à joints faciaux toriques conformes à l'ISO 8434-3
⎯ Partie 2: Flexibles avec embouts à cône à 24° et joints toriques conformes à l'ISO 8434-1 et à l'ISO 8434-4
⎯ Partie 3: Raccords de flexible avec brides conformes à l'ISO 6162-1 ou à l'ISO 6162-2
⎯ Partie 4: Flexibles avec éléments mâles métriques conformes à l'ISO 6149
⎯ Partie 5: Flexibles avec embouts évasés à 37° conformes à l'ISO 8434-2
⎯ Partie 6: Flexibles avec embouts à cône à 60° conformes à l'ISO 8434-6
iv © ISO 2010 – Tous droits réservés
---------------------- Page: 4 ----------------------
ISO 12151-1:2010(F)
Introduction
Dans les systèmes de transmissions hydrauliques, l'énergie est transmise et commandée par l'intermédiaire
d'un liquide sous pression circulant en circuit fermé. Dans les applications générales, le fluide peut être
véhiculé sous pression.
Les composants sont raccordés par leurs orifices au moyen d'éléments mâles fixés sur les raccords de tube
ou de tuyauterie ou sur les raccords de flexible et tuyaux.
© ISO 2010 – Tous droits réservés v
---------------------- Page: 5 ----------------------
NORME INTERNATIONALE ISO 12151-1:2010(F)
Raccordements pour transmissions hydrauliques
et applications générales — Raccords de flexible —
Partie 1:
Raccords de flexible avec embouts à joints faciaux toriques
conformes à l'ISO 8434-3
1 Domaine d'application
La présente partie de l'ISO 12151 spécifie les exigences générales et dimensionnelles pour la conception et
les performances des raccords de flexible avec embouts à joints faciaux toriques, en acier au carbone
conformes à l'ISO 8434-3, dont le diamètre intérieur nominal est compris entre 6,3 mm et 38 mm inclus en
conformité avec l'ISO 4397.
NOTE 1 D'autres matériaux peuvent être utilisés après accord entre le fabricant et l'utilisateur.
NOTE 2 Pour les raccords de flexible utilisés dans les systèmes de freinage hydrauliques et pneumatiques sur les
véhicules routiers (tels que définis dans le domaine d'application de l'ISO/TC 22, Véhicules routiers), voir l'ISO 4038,
l'ISO 4039-1 et l'ISO 4039-2.
Ces raccords de flexible (voir la Figure 1 pour un exemple type) sont destinés à être utilisés dans les
systèmes de transmissions hydrauliques avec des tuyaux qui répondent aux exigences des normes de tuyaux
respectives, et dans des applications générales lorsqu'il s'agit de tuyaux adaptés.
Légende
1 raccords de flexible 4 adaptateur en conformité avec l'ISO 8434-3
2 orifice en conformité avec l'ISO 6149-1 5 écrou
3 joint torique 6 joint torique
Figure 1 — Exemple type de raccord de flexible avec embout à joint facial torique
© ISO 2010 – Tous droits réservés 1
---------------------- Page: 6 ----------------------
ISO 12151-1:2010(F)
2 Références normatives
Les documents de référence suivants sont indispensables pour l'application du présent document. Pour les
références datées, seule l'édition citée s'applique. Pour les références non datées, la dernière édition du
document de référence s'applique (y compris les éventuels amendements).
ISO 68-2, Filetages ISO pour usages généraux — Profil de base — Partie 2: Filetages en inches
ISO 263, Filetages ISO en inches — Vue d'ensemble et sélection pour boulonnerie — Diamètres de 0,06 à
6 in
ISO 4397, Transmissions hydrauliques et pneumatiques — Raccords et éléments associés — Diamètres
extérieurs nominaux des tubes et tailles nominales des tuyaux flexibles
ISO 4759-1:2000, Tolérances des éléments de fixation — Partie 1: Vis, goujons et écrous — Grades A, B et C
ISO 5598, Transmissions hydrauliques et pneumatiques — Vocabulaire
ISO 5864:1993, Filetages ISO en inches — Jeux et tolérances
ISO 6149-1, Raccordements pour transmissions hydrauliques et applications générales — Orifices et éléments
mâles à filetage métrique ISO 261 et joint torique — Partie 1: Orifices à joint torique dans un logement
tronconique
ISO 6605, Transmissions hydrauliques — Tuyaux et ensembles flexibles — Méthodes d'essai
ISO 8434-3:2005, Raccordements de tubes métalliques pour transmissions hydrauliques et pneumatiques et
applications générales — Partie 3: Connecteurs à joints faciaux toriques
ISO 9227, Essais de corrosion en atmosphères artificielles — Essais aux brouillards salins
ISO 19879, Raccords de tubes métalliques pour transmissions hydrauliques et pneumatiques et applications
générales — Méthodes d'essai pour raccords pour transmissions hydrauliques
3 Termes et définitions
Pour les besoins du présent document, les termes et définitions donnés dans l'ISO 5598 s'appliquent.
4 Exigences relatives aux performances
4.1 Les raccords de flexible assemblés doivent satisfaire aux exigences de performances fixées dans la
spécification pertinente du flexible, sans présenter de fuite ou de rupture.
4.2 La pression de fonctionnement des assemblages flexibles doit être la plus basse des pressions
données selon la taille dans l'ISO 8434-3 et de la pression de fonctionnement indiquée dans la spécification
pertinente du flexible.
4.3 La portion sélectionnée des raccords de flexible assemblés doit faire l'objet d'essais conformément à
l'ISO 19879, et l'ensemble des assemblages flexibles doit faire l'objet d'essais conformément à l'ISO 6605.
5 Désignation des flexibles de raccordement
5.1 Les raccords de flexible doivent être désignés par un code alphanumérique pour faciliter la commande.
Ils doivent être désignés par la référence ISO 12151-1, suivie d'un trait d'union, puis des symboles littéraux du
type et de la forme d'extrémité de raccordement (voir 5.4), suivis d'un autre trait d'union, puis de la dimension
2 © ISO 2010 – Tous droits réservés
---------------------- Page: 7 ----------------------
ISO 12151-1:2010(F)
de l'embout à joints faciaux (diamètre extérieur nominal du tube conforme à l'ISO 8434-3) et de la taille du
tuyau (diamètre intérieur nominal conforme à l'ISO 4397), chacune des dimensions étant séparée par un
signe de multiplication (×).
EXEMPLE Un raccord de flexible pivotant avec un coude à 45° moyen, pour tube rigide de diamètre extérieur
nominal 12 mm et tuyau flexible de diamètre intérieur nominal 12,5 mm est désigné comme suit:
ISO 12151-1 - SWE45M – 12 × 12,5
5.2 La désignation du raccord de flexible par un symbole littéral doit comporter le type d'embout,
immédiatement suivi de la forme du raccord et du type d'écrou, s'il y a lieu.
5.3 Les extrémités mâles des tubes étant implicites, il n'est pas nécessaire de les inclure dans le code.
Cependant, si un autre type d'extrémité est prévu, il doit être désigné.
5.4 Les symboles littéraux donnés dans le Tableau 1 doivent être utilisés.
Tableau 1 — Symboles littéraux utilisés pour la désignation des raccords de flexible
Type d'extrémité de raccordement Symbole
Pivotant — SW
Forme Droit S
Coude à 90°, court ES
Coude à 90°, moyen EM
Coude à 90°, long EL
Coude à 45°, court E45S
Coude à 45°, moyen E45M
Surface d'étanchéité de l'écrou Surface d'étanchéité non exposée A
Surface d'étanchéité exposée B
6 Conception
6.1 Les dimensions des raccords de flexible représentés aux Figures 2 à 5 doivent être conformes à celles
données dans les Tableaux 2 à 5 et aux dimensions pertinentes de l'ISO 8434-3.
6.2 Les tolérances sur les cotes surplat des éléments hexagonaux doivent être conformes à
l'ISO 4759-1:2000, classe de qualité C. Les dimensions des surangles hexagonaux minimaux sont de
1,092 fois la largeur nominale des surplats. La largeur minimale d'un plat est de 0,43 fois la largeur nominale
des surplats.
6.3 La tolérance angulaire sur l'axe des extrémités des coudes doit être de ±3° pour toutes les dimensions.
6.4 Les détails du contour doivent être laissés au choix du fabricant, dans la mesure où les dimensions
données dans les Tableaux 2 à 5 sont respectées.
6.5 Les filetages sur les extrémités des raccords de flexible doivent être des filetages en inches ISO
conformes à l'ISO 263, et à l'ISO 8434-3:2005, Annexe A, sauf pour le filetage 1-14 UNS classes 2A et 2B,
dont les dimensions se trouvent aussi dans l'ISO 8434-3:2005, Annexe A.
© ISO 2010 – Tous droits réservés 3
---------------------- Page: 8 ----------------------
ISO 12151-1:2010(F)
7 Fabrication
7.1 Construction
Les raccords de flexible peuvent être forgés ou façonnés à froid, usinés à partir d'acier laminé ou fabriqués à
partir d'éléments multiples.
7.2 Qualité d'exécution
La qualité d'exécution doit être conforme aux meilleures pratiques commerciales pour donner des raccords de
flexible de haute qualité. Les raccords de flexible doivent être exempts de tout contaminant visuel, de toute
bavure, écaille et éclat qui pourraient se détacher lors de l'utilisation et de tout autre défaut qui pourrait altérer
la fonction des pièces. Toutes les surfaces usinées doivent avoir, sauf indication contraire, une rugosité de
surface Ra u 6,3 µm.
7.3 Finition
La surface extérieure et les filetages de toutes les parties en acier au carbone doivent être plaquées ou
revêtues d'un matériau capable de résister à un essai au brouillard salin pendant 72 h conformément à
l'ISO 9227, sauf accord contraire entre le fabricant et l'utilisateur. Toute apparition de rouille rouge pendant
l'essai au brouillard salin dans n'importe quelle zone, excepté celles notées ci-dessous, doit être considérée
comme une défaillance:
⎯ to
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.