SIST- TS CEN/TS 12200-2:2003
(Main)Plastics rainwater piping systems for above ground external use - Unplasticized poly(vinyl chloride) (PVC-U) - Part 2: Guidance for the assessment of conformity
Plastics rainwater piping systems for above ground external use - Unplasticized poly(vinyl chloride) (PVC-U) - Part 2: Guidance for the assessment of conformity
This Part of EN (155wi014) specifies procedures and requirements for the assessment of conformity to be included in the manufacturer's quality plan as part of the quality system for third party certification of conformity by a certification body accredited to EN 45011 or EN 45012, as applicable, and includes the following: a) Requirements for materials, components, joints and assemblies given in EN 12200-1; b) Requirements for the manufacturer's quality system given in EN 29001 or EN 29002, as applicable.
Kunststoff-Rohrleitungssysteme für außen liegende Regenfallleitungen - Weichmacherfreies Polyvinylchlorid (PVC-U) - Teil 2: Empfehlung für die Beurteilung der Konformität
Dieser Teil der EN 12200 gibt Empfehlungen für die Beurteilung der Konformität, die als Teil des Qualitätssicherungssystems im Qualitätssicherungsplan des Herstellers enthalten sein müssen.
Diese Technische Spezifikation enthält:
a) Anforderungen an Werkstoffe, Rohrleitungsteile, Verbindungen und Bauteilkombinationen, die in EN 12200 1:2000 festgelegt sind;
b) Anforderungen an das Qualitätssicherungssystem des Herstellers;
ANMERKUNG 1 Das Qualitätssicherungssystem sollte EN ISO 9001:2000[1] entsprechen.
c) Definitionen und Verfahren, die anzuwenden sind, wenn eine Fremdüberwachung enthalten ist.
ANMERKUNG 2 Ist eine Fremdüberwachung enthalten, wird empfohlen, diese durch eine in Abhängigkeit der Anwendung nach EN 45011[2] oder EN 45012[3] zugelassene Zertifizierungsstelle durchführen zu lassen.
Dieser Teil der EN 12200 gilt für Rohrleitungssysteme aus weichmacherfreiem Polyvinylchlorid (PVC U), die in außen liegenden Regenfallleitungen eingesetzt werden.
Systemes de canalisations de descentes d'eaux pluviales en plastique a usage externe en aérien - Poly(chlorure de vinyle) non plastifié (PVC-U) - Partie 2 : Guide pour l'évaluation de la conformité
La présente partie de l'EN 12200 donne un guide pour l'évaluation de la conformité a inclure dans le plan qualité du fabricant en tant que partie du systeme qualité.
La présente Spécification Technique comprend :
a) les exigences pour les matieres, les composants, les joints et les assemblages indiqués dans l'EN 12200-1:2000 ;
b) les exigences relatives au systeme qualité du fabricant ;
NOTE 1 Il est recommandé que le systeme de qualité soit conforme a l'EN ISO 9001:2000 [1].
c) les définitions et les procédures a appliquer si une certification par tierce partie est prise en compte.
NOTE 2 Si une certification par une tierce partie est prise en compte, il est recommandé que l'organisme de certification soit accrédité au sens de l'EN 45011[2] ou de l'EN 45012[3], selon le cas.
Cette partie de l'EN 12200 s'applique aux systemes de canalisations de descente d'eaux pluviales en poly(chlorure de vinyle) non plastifié (PVC-U) a usage externe en aérien.
Cevni sistemi iz polimernih materialov za odvod padavinskih voda za zunanjo uporabo - Nemehčan polivinilklorid (PVC-U) - 2. del: Smernice za ugotavljanje skladnosti
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST- TS CEN/TS 12200-2:2003
01-oktober-2003
&HYQLVLVWHPLL]SROLPHUQLKPDWHULDORY]DRGYRGSDGDYLQVNLKYRGD]D]XQDQMR
XSRUDER1HPHKþDQSROLYLQLONORULG 39&8 GHO 6PHUQLFH]DXJRWDYOMDQMH
VNODGQRVWL
Plastics rainwater piping systems for above ground external use - Unplasticized poly
(vinyl chloride) (PVC-U) - Part 2: Guidance for the assessment of conformity
Kunststoff-Rohrleitungssysteme für außen liegende Regenfallleitungen -
Weichmacherfreies Polyvinylchlorid (PVC-U) - Teil 2: Empfehlung für die Beurteilung der
Konformität
Systemes de canalisations de descentes d'eaux pluviales en plastique a usage externe
en aérien - Poly(chlorure de vinyle) non plastifié (PVC-U) - Partie 2 : Guide pour
l'évaluation de la conformité
Ta slovenski standard je istoveten z: CEN/TS 12200-2:2003
ICS:
23.040.03 Cevovodi za zunanje sisteme Pipeline and its parts for
transporta vode in njihovi deli external water conveyance
systems
SIST- TS CEN/TS 12200-2:2003 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST- TS CEN/TS 12200-2:2003
---------------------- Page: 2 ----------------------
SIST- TS CEN/TS 12200-2:2003
TECHNICAL SPECIFICATION
CEN/TS 12200-2
SPÉCIFICATION TECHNIQUE
TECHNISCHE SPEZIFIKATION
April 2003
ICS 23.040.01
English version
Plastics rainwater piping systems for above ground external use
- Unplasticized poly(vinyl chloride) (PVC-U) - Part 2: Guidance
for the assessment of conformity
This Technical Specification (CEN/TS) was approved by CEN on 25 November 2002 for provisional application.
The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to submit their
comments, particularly on the question whether the CEN/TS can be converted into a European Standard.
CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS available. It
is permissible to keep conflicting national standards in force (in parallel to the CEN/TS) until the final decision about the possible
conversion of the CEN/TS into an EN is reached.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2003 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN/TS 12200-2:2003 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST- TS CEN/TS 12200-2:2003
CEN/TS 12200-2:2003 (E)
Contents
page
Foreword .3
Introduction .4
1 Scope.5
2 Normative references.5
3 Terms and definitions, symbols and abbreviations.5
3.1 Terms and definitions .5
3.2 Abbreviations.7
4 Requirements.8
4.1 General.8
4.2 Testing and inspection .8
4.2.1 Material specification.8
4.2.2 Grouping.9
4.2.3 Type tests (TT) .9
4.2.4 Batch release tests (BRT) .11
4.2.5 Process verification tests (PVT) .11
4.2.6 Audit tests (AT).12
4.2.7 Indirect tests (IT).13
4.2.8 Inspection records and test records .13
Bibliography .14
2
---------------------- Page: 4 ----------------------
SIST- TS CEN/TS 12200-2:2003
CEN/TS 12200-2:2003 (E)
Foreword
This document (CEN/TS 12200-2:2003) has been prepared by CEN /TC 155 "Plastics piping systems
and ducting systems", the secretariat of which is held by NEN.
This Technical Specification can be used to support elaboration of national third party certification
procedures for products conforming to EN 12200-1.
This Technical Specification is a Part of a System Standard for plastics piping systems of a particular
material for a specific application. There are a number of such System Standards.
System Standards are based on the results of the work undertaken in ISO/TC 138 "Plastics pipes,
fittings and valves for the transport of fluids", which is a Technical Committee of the International
Organisation for Standardisation (ISO).
They are supported by separate standards on test methods to which references are made throughout
the System Standard.
The System Standards are consistent with general standards on functional requirements and on
recommended practice for installation.
EN 12200 consists of the following Parts, under the general title “Plastics rainwater piping systems for
above ground external use — Unplasticized poly (vinyl chloride) (PVC-U)”.
— Part 1: Specifications for pipes, fittings and the system;
— Part 2: Guidance for the assessment of conformity;
This part of EN 12200 includes a bibliography.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to announce this CEN Technical Specification: Austria, Belgium, Czech
Republic, Denmark, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Luxembourg,
Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and the United
Kingdom.
3
---------------------- Page: 5 ----------------------
SIST- TS CEN/TS 12200-2:2003
CEN/TS 12200-2:2003 (E)
Introduction
The System Standard, of which this is Part 2, specifies the requirements for a rainwater piping system
and its components made from unplasticized poly (vinyl chloride) (PVC-U). The piping system is
intended for above ground external use.
For material and components, requirements and test methods are specified in Part 1 of EN 12200.
Characteristics for fitness for purpose are also covered in Part 1.
This Part of EN 12200 covers procedures and requirements for the assessment of conformity of
materials, components, joints and assemblies and is intended to be used by certification bodies,
inspection bodies, testing laboratories and manufacturers.
4
---------------------- Page: 6 ----------------------
SIST- TS CEN/TS 12200-2:2003
CEN/TS 12200-2:2003 (E)
1 Scope
This Part of EN 12200 gives guidance for the assessment of conformity to be included in the
manufacturer's quality plan as part of the quality system.
This Technical Specification includes:
a) requirements for materials, components, joints and assemblies given in EN 12200-1:2000;
b) requirements for the manufacturer's quality system;
[1]
NOTE 1 It is recommended that the quality system conforms to EN ISO 9001:2000 .
c) definitions and procedures to be applied if third party certification is involved.
[2]
NOTE 2 If a third party certification is involved, it is recommended that the certification body is accredited to EN 45011 or
[3]
EN 45012 , as applicable.
This Part of EN 12200 is applicable to unplasticized poly (vinyl chloride) (PVC-U) rainwater piping
systems intended to be used for above ground external use.
2 Normative references
This Technical Specification incorporates by dated or undated reference, provisions from other
publications. These normative references are cited at the appropriate places in the text and the
publications are listed hereafter. For dated references, subsequent amendments to, or revisions of,
any of these publications apply to this Technical Specification only when incorporated in it by
amendment or revision. For undated references the latest edition of the publication referred to applies
(including amendments).
EN 12200-1:2000, Plastics rainwater piping systems for above ground external use — Unplasticized
poly(vinyl chloride) (PVC-U) — Part 1: Specifications for pipes, fittings and the system
3 Terms and definitions, symbols and abbreviations
For the purposes of this Technical Specification, the terms and definitions, symbols and abbreviations
given in EN 12200-1:2000, apply together with the following.
3.1 Terms and definitions
3.1.1
certification body
impartial body, governmental or non-governmental, possessing the necessary competence and
responsibility to carry out certification of conformity according to given rules of procedure and
management
3.1.2
inspection body
impartial organisation or company, approved by a certification body as possessing the necessary
competence to verify and/or to carry out initial type testing, audit testing and inspection of the
manufacturer's factory production control in accordance with the relevant European Standard
3.1.3
testing laboratory
laboratory which measures, tests, calibrates or otherwise determines the characteristics of the
performance of materials and products
5
---------------------- Page: 7 ----------------------
SIST- TS CEN/TS 12200-2:2003
CEN/TS 12200-2:2003 (E)
3.1.4
quality system
organisational structure, responsibilities, procedures, processes and resources for implementing
quality management
3.1.5
quality plan
document setting out the specific quality practices, resources and sequence of activities relevant to a
particular product or range of products
3.1.6
type testing (TT)
testing performed to prove that the material, component, joint or assembly is capable of conforming to
the requirements given in the relevant Standard
3.1.6.1
preliminary type testing (PTT)
type testing carried out by, or on behalf of, the manufacturer
3.1.6.2
initial type testing (ITT)
type testing carried out by, or on behalf of, a certification body for certification purposes
3.1.7
batch release test (BRT)
test performed by the manufacturer on a batch of components, which has to be satisfactorily
completed before the batch can be released
3.1.8
process verification test (PVT)
test performed by the manufacturer on materials, components, joints or assemblies at specific
intervals to confirm that the process continues to be capable of producing components conforming to
the requirements given in the relevant Standard
NOTE Such tests are not required to release batches of components and are carried out as a measure of process control.
3.1.9
audit test (AT)
test performed by, or on behalf of, a certification body to confirm that the material, component, joint or
assembly continues to conform to the requirements given in the System Standard and to provide
information to assess the effectiveness of the quality system
3.1.10
indirect testing
test performed by the manufacturer different from that specified for that particular characteristic having
verified its correlation with the specified test
3.1.11
witness testing
testing accepted by a certification body for initial type testing and/or audit testing, which is carried out
by, or on behalf of, the manufacturer and supervised by a representative of the certification body,
qualified in testing
3.1.12
material
defined type of polymer or additive or constituent thereof
6
---------------------- Page: 8 ----------------------
SIST- TS CEN/TS 12200-2:2003
CEN/TS 12200-2:2003 (E)
3.1.13
compound (blend)
recipe which defines types of polymer, additives or constituents at specified dosage levels
3.1.14
material batch or compound batch
clearly identifiable quantity of a particul
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.