SIST EN 62252:2005
(Main)Maritime navigation and radiocommunication equipment and systems - Radar for craft not in compliance with IMO SOLAS Chapter V - Performance requirements, methods of test and required test results
Maritime navigation and radiocommunication equipment and systems - Radar for craft not in compliance with IMO SOLAS Chapter V - Performance requirements, methods of test and required test results
Specifies the minimum performance requirements for testing and required test results for conformance of radar not fully compliant with the IMO Performance Standard for radar/radar plotting (MSC.64(67)). Covers radar classes A, B and C. Is based on EN 60872, EN 60936 and takes into account EN 60945.
Navigations- und Funkkommunikationsgeräte und -systeme für die Seeschifffahrt - Radar für Schiffe, die nicht IMO SOLAS Kapitel V entsprechen - Leistungsanforderungen, Prüfverfahren und geforderte Prüfergebnisse
Matériels et systèmes de navigation et de radiocommunication maritimes - Radars pour navires non conformes au Châpitre V de l'OMI-SOLAS - Exigences d'exploitation et de fonctionnement, méthodes d'essai et résultats d'essai exigés
Specifies the minimum performance requirements for testing and required test results for conformance of radar not fully compliant with the IMO Performance Standard for radar/radar plotting (MSC.64(67)). Covers radar classes A, B and C. Is based on EN 60872, EN 60936 and takes into account EN 60945.
Pomorska navigacijska in radiokomunikacijska oprema in sistemi – Radarji za plovila, ki niso skladni s 5. poglavjem konvencije IMO SOLAS – Zahteve za lastnosti, preskusne metode in zahtevani rezultati preskušanja (IEC 62252:2004)
General Information
Standards Content (Sample)
SLOVENSKI SIST EN 62252:2005
STANDARD
december 2005
Pomorska navigacijska in radiokomunikacijska oprema in sistemi – Radarji za
plovila, ki niso skladni s 5. poglavjem konvencije IMO SOLAS – Zahteve za
lastnosti, preskusne metode in zahtevani rezultati preskušanja (IEC
62252:2004)
Maritime navigation and radiocommunication equipment and systems – Radar for
craft not in compliance with IMO SOLAS Chapter V – Performance requirements,
methods of test and required test results (IEC 62252:2004)
ICS 47.020.70 Referenčna številka
SIST EN 62252:2005(en)
© Standard je založil in izdal Slovenski inštitut za standardizacijo. Razmnoževanje ali kopiranje celote ali delov tega dokumenta ni dovoljeno
---------------------- Page: 1 ----------------------
EUROPEAN STANDARD EN 62252
NORME EUROPÉENNE
EUROPÄISCHE NORM November 2004
ICS 47.020.70
English version
Maritime navigation and radiocommunication equipment and systems –
Radar for craft not in compliance with IMO SOLAS Chapter V –
Performance requirements, methods of test and required test results
(IEC 62252:2004)
Matériels et systèmes de navigation Navigations- und Funk-
et de radiocommunication maritimes – kommunikationsgeräte und -systeme
Radars pour navires non conformes für die Seeschifffahrt –
au Chapitre V de l'OMI-SOLAS – Radar für Schiffe, die nicht IMO SOLAS
Exigences d'exploitation et Kapitel V entsprechen –
de fonctionnement, méthodes d'essai Leistungsanforderungen, Prüfverfahren
et résultats d'essai exigés und geforderte Prüfergebnisse
(CEI 62252:2004) (IEC 62252:2004)
This European Standard was approved by CENELEC on 2004-10-01. CENELEC members are bound to
comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and
notified to the Central Secretariat has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden,
Switzerland and United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
Central Secretariat: rue de Stassart 35, B - 1050 Brussels
© 2004 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 62252:2004 E
---------------------- Page: 2 ----------------------
EN 62252:2004 - 2 -
Foreword
The text of document 80/393/FDIS, future edition 1 of IEC 62252, prepared by IEC TC 80, Maritime
navigation and radiocommunication equipment and systems, was submitted to the IEC-CENELEC
parallel vote and was approved by CENELEC as EN 62252 on 2004-10-01.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2005-07-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2007-10-01
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 62252:2004 was approved by CENELEC as a European
Standard without any modification.
__________
---------------------- Page: 3 ----------------------
- 3 - EN 62252:2004
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
NOTE Where an international publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
Publication Year Title EN/HD Year
IEC 60068-2-52 1996 Environmental testing EN 60068-2-52 1996
Corr. July 1996 Part 2: Tests - Test Kb: Salt mist, cyclic
(sodium chloride solution)
IEC 60071-2 1996 Insulation co-ordination EN 60071-2 1997
Part 2: Application guide
1)
IEC 60092-101 - Electrical installations in ships - -
Part 101: Definitions and general
requirements
database
IEC 60417 Graphical symbols for use on equipment - -
IEC 60529 1989 Degrees of protection provided by EN 60529 1991
enclosures (IP Code) + corr. May 1993
IEC 60533 1999 Electrical and electronic installations in - -
ships - Electromagnetic compatibility
IEC 60872-2 1999 Maritime navigation and EN 60872-2 1999
radiocommunication equipment and
systems - Radar plotting aids
Part 2: Automatic tracking aids (ATA) -
Methods of testing and required test
results
IEC 60872-3 2000 Part 3: Electronic plotting aid (EPA) - EN 60872-3 2001
Performance requirements - Methods of
testing and required test results
IEC 60936-1 1999 Maritime navigation and EN 60936-1 2000
radiocommunication equipment and
systems - Radar
Part 1: Shipborne radar - Performance
requirements - Methods of testing and
required test results
IEC 60936-2 1998 Part 2: Shipborne radar for high-speed EN 60936-2 1999
craft (HSC) - Methods of testing and
required test results
1)
Undated reference.
---------------------- Page: 4 ----------------------
EN 62252:2004 - 4 -
Publication Year Title EN/HD Year
IEC 60936-3 2002 Part 3: Radar with chart facilities - EN 60936-3 2002
Performance requirements - Methods of
testing and required test results
1) 2)
IEC 60945 - Maritime navigation and EN 60945 2002
radiocommunication equipment and
systems - General requirements -
Methods of testing and required test
results
IEC 61000-4-8 1993 Electromagnetic compatibility (EMC) EN 61000-4-8 1993
Part 4-8: Testing and measurement
techniques - Power frequency magnetic
field immunity test
IEC 61108 Series Maritime navigation and EN 61108 Series
radiocommunication equipment and
systems - Global navigation satellite
systems (GNSS)
IEC 61162 Series Maritime navigation and EN 61162 Series
radiocommunication equipment and
systems - Digital interfaces
IEC 61672 Series Electroacoustics-Sound level meters - -
1)
IEC/PAS - Maritime navigation and - -
60936-5 radiocommunication equipment and
systems - Radar
Part 5: Guidelines for the use and display
of AIS information on radar
ISO 694 2000 Ships and marine technology - EN ISO 694 2001
Positioning of magnetic compasses in
ships
ISO 3791 1976 Office machines and data processing - -
equipment - Keyboard layouts for numeric
applications
ITU Radio 2001 Radio Regulations - -
Regulations
1)
ITU-R - Techniques for measurement of - -
Recommendation
unwanted emissions of radar systems
M.1177-3
1)
ITU-R - Technical characteristics of maritime - -
Recommendation
radionavigation radars
M.1313
1)
ITU-R - Spectra and bandwidth of emissions - -
Recommendation
SM.328-9
2)
Valid edition at date of issue.
---------------------- Page: 5 ----------------------
- 5 - EN 62252:2004
Publication Year Title EN/HD Year
1)
ITU-R - Unwanted emissions in the spurious - -
Recommendation
domain
SM.329-10
1)
ITU-R - Variation of the boundary between the - -
Recommendation
out-of-band and spurious domains
SM.1539
required for the application of
Recommendations ITU-R SM.1541 and
ITU-R SM.329
1)
ITU-R - Unwanted emissions in the out-of-band - -
Recommendation domain falling into adjacent allocated
SM.1540
bands
1)
ITU-R - Unwanted emissions in the out-of-band - -
Recommendation domain
SM.1541
1)
ITU-T - Arrangement of digits, letters and - -
Recommendation
symbols on telephones and other devices
E.161
that can be used for gaining access to a
telephone network
1)
IHO S-52 - Specifications for chart content and - -
display aspects of ECDIS
---------------------- Page: 6 ----------------------
INTERNATIONAL IEC
STANDARD 62252
First edition
2004-07
Maritime navigation and radiocommunication
equipment and systems –
Radar for craft not in compliance
with IMO SOLAS Chapter V –
Performance requirements, methods
of test and required test results
© IEC 2004 ⎯ Copyright - all rights reserved
No part of this publication may be reproduced or utilized in any form or by any means, electronic or
mechanical, including photocopying and microfilm, without permission in writing from the publisher.
International Electrotechnical Commission, 3, rue de Varembé, PO Box 131, CH-1211 Geneva 20, Switzerland
Telephone: +41 22 919 02 11 Telefax: +41 22 919 03 00 E-mail: inmail@iec.ch Web: www.iec.ch
PRICE CODE
Commission Electrotechnique Internationale XG
International Electrotechnical Commission
ɆɟɠɞɭɧɚɪɨɞɧɚɹɗɥɟɤɬɪɨɬɟɯɧɢɱɟɫɤɚɹɄɨɦɢɫɫɢɹ
For price, see current catalogue
---------------------- Page: 7 ----------------------
– 2 – 62252 © IEC:2004(E)
CONTENTS
FOREWORD.5
INTRODUCTION.7
1 Scope.8
2 Normative references.8
3 Definitions and abbreviations.9
3.1 Definitions.9
3.2 Abbreviations.12
4 Performance requirements.13
4.1 Radar indication.13
4.2 Safety of options .13
4.3 Technical information.13
4.4 Quality assurance.13
4.5 Radio-frequency spectrum requirements.13
4.6 Range.13
4.7 Display.14
4.8 Frequency band.16
4.9 Range markers.16
4.10 Range measurement using range rings and VRM .17
4.11 Heading line.17
4.12 Electronic bearing line (EBL) .17
4.13 Bearing scale.18
4.14 Discrimination.19
4.15 Antenna radiation pattern.19
4.16 Roll or pitch performance .19
4.17 Antenna scan.19
4.18 Modes.20
4.19 Tuning indication.21
4.20 Anti-clutter devices.21
4.21 Range performance in clutter .21
4.22 Operation.22
4.23 Controls.22
4.24 Manual speed set and drift input.22
4.25 Interference from external magnetic fields .22
4.26 Radar installation.22
4.27 Failure warnings (alarms) and status indication .23
4.28 Interfacing.23
4.29 Navigational information.24
4.30 Ergonomics.24
4.31 Display of information.26
4.32 Safety precautions.26
4.33 Spurious/unwanted frequency emissions (Annex D) .26
5 Methods of test and required test result.26
5.1 Radar indication.27
5.2 Safety of options .28
5.3 Technical information.28
---------------------- Page: 8 ----------------------
62252 © IEC:2004(E) – 3 –
5.4 Quality assurance.28
5.5 Radio-frequency spectrum requirements.28
5.6 Range.28
5.7 Display.29
5.8 Frequency band.31
5.9 Range markers.32
5.10 Range measurement using range rings and VRM .33
5.11 Heading line.33
5.12 Electronic bearing line (EBL) .34
5.13 Bearing scale.36
5.14 Discrimination.37
5.15 Antenna radiation pattern.38
5.16 Roll and pitch performance.39
5.17 Antenna scan.39
5.18 Modes.40
5.19 Tuning indication.42
5.20 Anti-clutter devices.43
5.21 Range performance in clutter .43
5.22 Operation.44
5.23 Controls.44
5.24 Manual speed set and drift .45
5.25 Interference from external magnetic fields .45
5.26 Radar installation.45
5.27 Failure warnings (alarms) and status indications .45
5.28 Interfacing.46
5.29 Navigational information.48
5.30 Ergonomics.49
5.31 Display of information.49
5.32 Safety precautions.50
5.33 Spurious/unwanted frequency emissions.50
Annex A (normative) Method for relating the radar cross-section (echoing area) of one
radar target with another.51
Annex B (normative) Standard names, abbreviations and symbols for control functions
on marine navigational radar equipment (as referenced by IEC 60945).56
Annex C (normative) Guidelines for the display of navigational information on radar
by means of radar maps .68
Annex D (normative) Unwanted emissions of radar systems – Methods of
measurement and required results .70
Annex E (normative) General requirements – Method of test and required results.75
Annex F (normative) Automatic tracking device (ATD) – Methods of testing and
required test results – Class A only.102
Annex G (normative) Electronic plotting device (EPD) Class A only .117
Annex H (normative) Electronic plotting video symbols (EPVS).126
Annex I (informative) Performance checks during environmental testing .142
---------------------- Page: 9 ----------------------
– 4 – 62252 © IEC:2004(E)
Figure A.1 – Enhancement by reflection (dB) over free space .54
Figure A.2 – Enhancement by reflection (dB) over free space .55
Figure D.1 – B falls within the allocated band.73
–40
Figure D.2 – B falls outside the allocated band.74
–40
Figure G.1 – Diagram of three plots .125
Table 1 – Effective side-lobes .19
Table 2 – Recommended input data sentences – IEC 61162-1/IEC 61162-2 .23
Table 3 – Output data sentences – IEC 61162-1/IEC 61162-2 where available .24
Table 4 – 3 dB points for main beam.38
Table 5 – Effective side-lobes .39
Table C.1 – Features and colours to be used for radar maps .69
Table D.1 – Measurement frequency ranges .71
Table E.1 – Extreme power supplies variation.84
Table E.2 – Schedule of performance tests and checks .89
Table E.3 – Durability and resistance to environmental conditions .90
Table E.4 – Test severity – half-sine pulse.94
Table E.5 – Emission limits.100
Table F.1 – Accuracy values .107
Table F.2 – Accuracy values .107
Table F.3 – ATD Scenarios .114
Table G.1 – Test scenarios .120
Table G.2 – Scenario 1 data .122
Table G.3 – Scenario 2 data .122
Table G.4 – Scenario 3 data .123
Table G.5 – Scenario 4 data .123
Table G.6 – Scenario 5 data .124
Table G.7 – Scenario 6 data .124
---------------------- Page: 10 ----------------------
62252 © IEC:2004(E) – 5 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
MARITIME NAVIGATION AND RADIOCOMMUNICATION
EQUIPMENT AND SYSTEMS –
RADAR FOR CRAFT NOT IN COMPLIANCE WITH
IMO SOLAS CHAPTER V –
PERFORMANCE REQUIREMENTS, METHODS
OF TEST AND REQUIRED TEST RESULTS
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with an IEC Publication.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 62252 has been prepared by IEC technical committee 80: Maritime
navigation and radiocommunication equipment and systems.
This standard is based on the standards for radar and radar plotting used on SOLAS vessels,
IEC 60872 series, IEC 60936 series and IEC 60945.
The text of this standard is based on the following documents:
FDIS Report on voting
80/393/FDIS 80/397/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
---------------------- Page: 11 ----------------------
– 6 – 62252 © IEC:2004(E)
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
The committee has decided that the contents of this publication will remain unchanged until
the maintenance result date indicated on the IEC web site under "http://webstore.iec.ch" in
the data related to the specific publication. At this date, the publication will be
• reconfirmed;
• withdrawn;
• replaced by a revised edition, or
• amended.
A bilingual version of this publication may be issued at a later date.
---------------------- Page: 12 ----------------------
62252 © IEC:2004(E) – 7 –
INTRODUCTION
This IEC radar standard is produced specifically for radar not fully compliant with the IMO
Performance Standard for radar/radar plotting and applies to the following:
• radar (class A) intended for commercial craft under 150 gross tonnage, where no SOLAS
radar carriage requirement currently exists, where the antenna beamwidth is not more
than 4,0° and the display minimum effective diameter is limited to not less than 150 mm.
• radar (class B) intended for recreational craft or other maritime use and where the
antenna beamwidth is not more than 5,5° and the display minimum effective diameter is
limited to not less than 85 mm.
• radar (class C) intended for small recreational craft where the antenna beamwidth is not
more than 7,5° and the display minimum effective diameter is limited to not less than
75 mm.
The requirements for commercial craft radar are covered in the main body of this
specification. The requirements, where different, for radar (class B and C) are shown in
parenthesis where applicable.
NOTE 1 The IMO performance standard for radar/radar plotting is in Resolution MSC.64(67) which is
implemented in the IEC 60872 series and the IEC 60936 series of standards.
NOTE 2 For the purposes of this IEC standard, the words 'craft’ and ‘ship’ are interchangeable and have the
same meaning.
---------------------- Page: 13 ----------------------
– 8 – 62252 © IEC:2004(E)
MARITIME NAVIGATION AND RADIOCOMMUNICATION
EQUIPMENT AND SYSTEMS –
RADAR FOR CRAFT NOT IN COMPLIANCE WITH
IMO SOLAS CHAPTER V –
PERFORMANCE REQU
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.