SIST EN ISO 15465:2004
(Main)Pipework - Stripwound metal hoses and hose assemblies (ISO 15465:2004)
Pipework - Stripwound metal hoses and hose assemblies (ISO 15465:2004)
ISO 15465:2004 specifies the requirements for the design, manufacture and testing of four principal types of stripwound metal hose and hose assemblies, of which only one type is for pressure applications. The four are: single overlap, unpacked and packed; double overlap, unpacked and packed, the last of these having maximum permissible pressures of up to 40 bar.
These hoses and hose assemblies may be supplied in nominal sizes from DN 6 to DN 500 and may operate at temperatures up to 600 °C dependent on materials of construction.
Rohrleitungen - Gewickelte Metallschläuche und Schlauchleitungen (ISO 15465:2004)
Diese Internationale Norm legt die Anforderungen für die Konstruktion, Herstellung und Prüfung von vier Haupt-typen von gewickelten Metallschläuchen und Schlauchleitungen fest, von denen lediglich eine Bauart für Anwendungsfälle unter Druckbeanspruchung vorgesehen ist. Die vier Bauarten sind: Schläuche mit einfacher Über-lappung, mit oder ohne Dichtung, sowie mit doppelter Überlappung, mit oder ohne Dichtung, wobei für letztere maximal zulässige Drücke bis 40 bar gelten.
Diese Schläuche und Schlauchleitungen können in Nennweiten DN 6 bis DN 500 geliefert werden und je nach den für die Herstellung verwendeten Werkstoffen bei Temperaturen bis 600 °C betrieben werden.
Tuyauteries - Tuyaux et tuyauteries métalliques flexibles agrafés (ISO 15465:2004)
L'ISO 15465:2004 spécifie les exigences pour la conception, la fabrication et les essais des quatre principaux types de tuyaux et tuyauteries métalliques flexibles agrafés, dont un seul type est destiné aux applications sous pression. Les quatre types sont: agrafage simple, sans joint et avec joint, et agrafage double, sans joint et avec joint, ce dernier type ayant des pressions maximales admissibles inférieures ou égales à 40 bar.
Ces tuyaux et tuyauteries flexibles peuvent être fournis dans des diamètres nominaux de DN 6 à DN 500 et peuvent être utilisés à des températures inférieures ou égales à 600 °C en fonction des matériaux de fabrication.
Cevovod - Ovite kovinske cevi in cevni priključki (ISO 15465:2004)
General Information
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Rohrleitungen - Gewickelte Metallschläuche und Schlauchleitungen (ISO 15465:2004)Tuyauteries - Tuyaux et tuyauteries métalliques flexibles agrafés (ISO 15465:2004)Pipework - Stripwound metal hoses and hose assemblies (ISO 15465:2004)23.040.70Gumene cevi in armatureHoses and hose assembliesICS:Ta slovenski standard je istoveten z:EN ISO 15465:2004SIST EN ISO 15465:2004en01-september-2004SIST EN ISO 15465:2004SLOVENSKI
STANDARD
SIST EN ISO 15465:2004
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN ISO 15465March 2004ICS 23.040.70English versionPipework - Stripwound metal hoses and hose assemblies (ISO15465:2004)Tuyauteries - Tuyaux et tuyauteries métalliques flexiblesagrafés (ISO 15465:2004)Rohrleitungen - Gewickelte Metallschläuche undMetallschlauchleitungen (ISO 15465:2004)This European Standard was approved by CEN on 1 March 2004.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2004 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN ISO 15465:2004 ESIST EN ISO 15465:2004
EN ISO 15465:2004 (E)2ForewordThis document (EN ISO 15465:2004) has been prepared by Technical Committee ISO/TC 5"Ferrous metal pipes and metallic fittings" in collaboration with Technical Committee CEN/TC342 "Metal hoses, hose assemblies, bellows and expansion joints", the secretariat of which isheld by UNI.This European Standard shall be given the status of a national standard, either by publication ofan identical text or by endorsement, at the latest by August 2004, and conflicting nationalstandards shall be withdrawn at the latest by August 2004.According to the CEN/CENELEC Internal Regulations, the national standards organizations ofthe following countries are bound to implement this European Standard: Austria, Belgium,Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary,Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.Endorsement noticeThe text of ISO 15465:2004 has been approved by CEN as EN ISO 15465:2004 without anymodifications.SIST EN ISO 15465:2004
Reference numberISO 15465:2004(E)© ISO 2004
INTERNATIONAL STANDARD ISO15465First edition2004-03-15Pipework — Stripwound metal hoses and hose assemblies Tuyauteries — Tuyaux et tuyauteries métalliques flexibles agrafés
SIST EN ISO 15465:2004
ISO 15465:2004(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
©
ISO 2004 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56 • CH-1211 Geneva 20 Tel.
+ 41 22 749 01 11 Fax
+ 41 22 749 09 47 E-mail
copyright@iso.org Web
www.iso.org Published in Switzerland
ii © ISO 2004 – All rights reserved
SIST EN ISO 15465:2004
ISO 15465:2004(E) © ISO 2004 – All rights reserved iii Contents Page Foreword.iv Introduction.v 1 Scope.1 2 Normative references.1 3 Terms and definitions.1 4 Information to be supplied by the purchaser.1 5 Hose types.2 6 Requirements.3 6.1 Materials.3 6.2 Hose dimensions.4 6.3 Tensile strength.5 6.4 Crush strength.5 6.5 Temperature.6 6.6 Pressure (for type DOP hose only).8 6.7 Assembly.8 7 Type tests.8 7.1 Tensile strength test.8 7.2 Crush strength test.9 7.3 Bend test.10 7.4 Pressure test (for type DOP hose).11 8 Production tests — Pressure proof test (for type DOP hose).11 9 Designation.11 10 Marking.12 Bibliography.13
SIST EN ISO 15465:2004
ISO 15465:2004(E) iv © ISO 2004 – All rights reserved Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 15465 was prepared by Technical Committee ISO/TC 5, Ferrous metal pipes and metallic fittings, Subcommittee SC 11, Metal hoses and expansion joints. This first edition of ISO 15465 cancels and replaces ISO 7657:1995, ISO 7658:1984, ISO 8444:1985, ISO 8445:1995, ISO 8446:1995, ISO 8447:1986, ISO 8448:1986, ISO 8449:1995 and ISO 8450:1986 of which it constitutes a technical revision. SIST EN ISO 15465:2004
ISO 15465:2004(E) © ISO 2004 – All rights reserved v Introduction It was decided to produce an International Standard under the Vienna Agreement, on technical cooperation between ISO and the European Committee for Standardization, CEN, in order to maintain one document. The opportunity was taken to replace all existing stripwound standards into this single document and to reformat it such that its layout is similar to the Internatioanl Standard for corrugated hose, ISO 10380. At the same time, additional information has been included which was not available when the replaced standards were originally produced. This document is a base standard for stripwound metal hoses and hose assemblies for general purposes.
SIST EN ISO 15465:2004
SIST EN ISO 15465:2004
INTERNATIONAL STANDARD ISO 15465:2004(E) © ISO 2004 – All rights reserved 1 Pipework — Stripwound metal hoses and hose assemblies 1 Scope This International Standard specifies the requirements for the design, manufacture and testing of four principal types of stripwound metal hose and hose assemblies, of which only one type is for pressure applications. The four are: single overlap, unpacked and packed; double overlap, unpacked and packed, the last of these having maximum allowable pressures of up to 40 bar. These hoses and hose assemblies may be supplied in nominal sizes from DN 6 to DN 500 and may operate at temperatures up to 600 °C dependent on materials of construction. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 554, Standard atmospheres for conditioning and/or testing — Specifications ISO 1634-1, Wrought copper and copper alloy plate, sheet and strip — Part 1: Technical conditions of delivery for plate, sheet and strip for general purposes ISO 2081, Metallic coatings — Electroplated coatings of zinc on iron or steel ISO 6317, Hot-rolled carbon steel strip of commercial and drawing qualities ISO 7369, Pipework — Metal hoses and hose assemblies — Vocabulary ISO 9328-5, Steel plates and strips for pressure purposes — Technical delivery conditions — Part 5: Austenitic steels ISO 10380, Pipework — Corrugated metal hoses and hose assemblies EN 10028-7, Flat products made of steels for pressure purposes — Part 7: Stainless steels 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 7369 apply. 4 Information to be supplied by the purchaser 4.1 The purchaser shall state the following in enquiries and orders a) application; b) nominal size and hose assembly length and whether measured in mid- or extended position; SIST EN ISO 15465:2004
ISO 15465:2004(E) 2 © ISO 2004 – All rights reserved c) hose type; d) maximum operating pressure; e) temperature range; f) materials; g) type of fitting. 4.2 Dependent on the application the purchaser shall provide the following information a) whether additional testing is required; b) service life; c) product to be conveyed; d) product velocity; e) any special information concerning choice of materials; f) movement and/or vibration; g) any additional requirements for cleaning and post test treatment; h) requirements for test certificates; i) if a coloured cover or other identification is required; j) any special requirements for packaging; k) requirements for user instructions. 5 Hose types 5.1 Type SOU: single overlap, unpacked — see Figure 1
Figure 1 — Cross-section of a type SOU, single overlap, unpacked hose
5.2 Type SOP: single overlap, packed — see Figure 2
Figure 2 — Cross-section of a type SOP, single overlap, packed hose SIST EN ISO 15465:2004
ISO
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.