SIST EN 62604-1:2015
(Main)Surface acoustic wave (SAW) and bulk acoustic wave (BAW) duplexers of assessed quality - Part 1: Generic specification
Surface acoustic wave (SAW) and bulk acoustic wave (BAW) duplexers of assessed quality - Part 1: Generic specification
This part of IEC 62604 specifies the methods of test and general requirements for SAW and
BAW duplexers of assessed quality using either capability approval or qualification approval
procedures.
Oberflächenwellen-(OFW-) und Volumenwellen-(BAW-)Duplexer mit bewerteter Qualität – Teil 1: Fachgrundspezifikation
Duplexeurs à ondes acoustiques de surface (OAS) et à ondes acoustiques de volume (OAV) sous assurance de la qualité - Partie 1: Spécification générique
IEC 62604-1:2015 spécifie les méthodes d'essai et les exigences générales pour les duplexeurs à OAS et à OAV dont la qualité est garantie par les procédures d'agrément de savoir-faire ou par les procédures d'homologation.
Radiofrekvenčni (SAW) in visokofrekvenčni (BAW) duplekserji ocenjene kakovosti - 1. del: Splošna specifikacija
Ta del standarda IEC 62604 določa preskusne metode in splošne zahteve za radiofrekvenčne (SAW) in visokofrekvenčne (BAW) duplekserje ocenjene kakovosti, ki vključujejo postopke za odobritev zmogljivosti ali kvalifikacije.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 62604-1:2015
01-december-2015
5DGLRIUHNYHQþQL 6$: LQYLVRNRIUHNYHQþQL %$: GXSOHNVHUMLRFHQMHQHNDNRYRVWL
GHO 6SORãQDVSHFLILNDFLMD
Surface acoustic wave (SAW) and bulk acoustic wave (BAW) duplexers of assessed
quality - Part 1: Generic specification
Duplexeurs à ondes acoustiques de surface (OAS) et à ondes acoustiques de volume
(OAV) sous assurance de la qualité - Partie 1: Spécification générique
Ta slovenski standard je istoveten z: EN 62604-1:2015
ICS:
31.140 3LH]RHOHNWULþQHLQ Piezoelectric and dielectric
GLHOHNWULþQHQDSUDYH devices
SIST EN 62604-1:2015 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 62604-1:2015
---------------------- Page: 2 ----------------------
SIST EN 62604-1:2015
EUROPEAN STANDARD EN 62604-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
September 2015
ICS 31.140
English Version
Surface acoustic wave (SAW) and bulk acoustic wave (BAW)
duplexers of assessed quality - Part 1: Generic specification
(IEC 62604-1:2015)
Duplexeurs à ondes acoustiques de surface (OAS) et à Oberflächenwellen-(OFW-) und Volumenwellen-(BAW-)
ondes acoustiques de volume (OAV) sous assurance de la Duplexer mit bewerteter Qualität - Teil 1:
qualité - Partie 1: Spécification générique Fachgrundspezifikation
(IEC 62604-1:2015) (IEC 62604-1:2015)
This European Standard was approved by CENELEC on 2015-08-20. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 62604-1:2015 E
---------------------- Page: 3 ----------------------
SIST EN 62604-1:2015
EN 62604-1:2015
European foreword
The text of document 49/1143/FDIS, future edition 1 of IEC 62604-1, prepared by IEC/TC 49
"Piezoelectric, dielectric and electrostatic devices and associated materials for frequency control,
selection and detection" was submitted to the IEC-CENELEC parallel vote and approved by
CENELEC as EN 62604-1:2015.
The following dates are fixed:
• latest date by which the document has to be implemented at (dop) 2016-05-20
national level by publication of an identical national
standard or by endorsement
(dow) 2018-08-20
• latest date by which the national standards conflicting with
the document have to be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such
patent rights.
Endorsement notice
The text of the International Standard IEC 62604-1:2015 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards indicated:
IEC 60068-2-10:2005 NOTE Harmonized as EN 60068-2-10:2005 (not modified).
IEC 60862-1:2003 NOTE Harmonized as EN 60862-1:2003 (not modified).
IEC 60862-2:2012 NOTE Harmonized as EN 60862-2:2012 (not modified).
IEC 61019-1:2004 NOTE Harmonized as EN 61019-1:2005 (not modified).
IEC 62047-7:2011 NOTE Harmonized as EN 62047-7:2011 (not modified).
IEC 62604-2:2011 NOTE Harmonized as EN 62604-2:2012 (not modified).
2
---------------------- Page: 4 ----------------------
SIST EN 62604-1:2015
EN 62604-1:2015
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod),
the relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is
available here: www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 60027 series Letter symbols to be used in electrical - -
technology
IEC 60050 series International Electrotechnical Vocabulary - -
IEC 60068-1 2013 Environmental testing - EN 60068-1 2014
Part 1: General and guidance
IEC 60068-2-1 - Environmental testing - EN 60068-2-1 -
Part 2-1: Tests - Test A: Cold
IEC 60068-2-2 - Environmental testing - EN 60068-2-2 -
Part 2-2: Tests - Test B: Dry heat
IEC 60068-2-6 - Environmental testing - EN 60068-2-6 -
Part 2-6: Tests - Test Fc: Vibration
(sinusoidal)
IEC 60068-2-7 - Basic environmental testing procedures - EN 60068-2-7 -
Part 2-7: Tests - Test Ga and guidance:
Acceleration, steady state
IEC 60068-2-13 - Basic environmental testing procedures - EN 60068-2-13 -
Part 2-13: Tests - Test M: Low air pressure
IEC 60068-2-14 - Environmental testing - EN 60068-2-14 -
Part 2-14: Tests - Test N: Change of
temperature
IEC 60068-2-17 1994 Basic environmental testing procedures - EN 60068-2-17 1994
Part 2-17: Tests - Test Q: Sealing
IEC 60068-2-27 - Environmental testing - EN 60068-2-27 -
Part 2-27: Tests - Test Ea and guidance:
Shock
IEC 60068-2-30 - Environmental testing - EN 60068-2-30 -
Part 2-30: Tests - Test Db: Damp heat,
cyclic (12 h + 12 h cycle)
3
---------------------- Page: 5 ----------------------
SIST EN 62604-1:2015
EN 62604-1:2015
Publication Year Title EN/HD Year
IEC 60068-2-31 - Environmental testing - EN 60068-2-31 -
Part 2-31: Tests - Test Ec: Rough handling
shocks, primarily for equipment-type
specimens
IEC 60068-2-45 - Basic environmental testing procedures - EN 60068-2-45 -
Part 2-45: Tests - Test XA and guidance:
Immersion in cleaning solvents
IEC 60068-2-52 - Environmental testing - EN 60068-2-52 -
Part 2-52: Tests - Test Kb: Salt mist, cyclic
(sodium chloride solution)
IEC 60068-2-58 - Environmental testing - EN 60068-2-58 -
Part 2-58: Tests - Test Td: Test methods
for solderability, resistance to dissolution of
metallization and to soldering heat of
surface mounting devices (SMD)
IEC 60068-2-64 - Environmental testing - EN 60068-2-64 -
Part 2-64: Tests - Test Fh: Vibration,
broadband random and guidance
IEC 60068-2-78 - Environmental testing - EN 60068-2-78 -
Part 2-78: Tests - Test Cab: Damp heat,
steady state
IEC 60122-1 - Quartz crystal units of assessed quality - EN 60122-1 -
Part 1: Generic specification
IEC 60617-DB - Graphical symbols for diagrams - -
IEC 60642 - Piezoelectric ceramic resonators and - -
resonator units for frequency control and
selection - Chapter I: Standard values and
conditions - Chapter II: Measuring and test
conditions
IEC 60695-11-5 - Fire hazard testing - EN 60695-11-5 -
Part 11-5: Test flames - Needle-flame test
method - Apparatus, confirmatory test
arrangement and guidance
1) 1)
IEC 60749-28 - Semiconductor devices - Mechanical and FprEN 60749-28 -
climatic test methods -
Part 28: Electrostatic Discharge (ESD)
Sensitivity Testing Direct contact charged
device model (DC-CDM)
IEC 61000-4-2 - Electromagnetic compatibility (EMC) - EN 61000-4-2 -
Part 4-2: Testing and measurement
techniques - Electrostatic discharge
immunity test
IEC 61340-3-1 - Electrostatics - EN 61340-3-1 -
Part 3-1: Methods for simulation of
electrostatic effects - Human body model
(HBM) electrostatic discharge test
waveforms
1) At draft stage.
4
---------------------- Page: 6 ----------------------
SIST EN 62604-1:2015
EN 62604-1:2015
Publication Year Title EN/HD Year
IEC 61340-3-2 - Electrostatics - EN 61340-3-2 -
Part 3-2: Methods for simulation of
electrostatic effects - Machine model (MM)
electrostatic discharge test waveforms
IEC 62761 - Guidelines for the measurement method of EN 62761 -
nonlinearity for surface acoustic wave
(SAW) and bulk acoustic wave (BAW)
devices in radio frequency (RF)
IEC 80000 series Quantities and units EN 80000 series
ISO 80000 series Quantities and units - EN ISO 80000 series
5
---------------------- Page: 7 ----------------------
SIST EN 62604-1:2015
---------------------- Page: 8 ----------------------
SIST EN 62604-1:2015
IEC 62604-1
®
Edition 1.0 2015-07
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
Surface acoustic wave (SAW) and bulk acoustic wave (BAW) duplexers of
assessed quality –
Part 1: Generic specification
Duplexeurs a ondes acoustiques de surface (OAS) et a ondes acoustiques de
volume (OAV) sous assurance de la qualite –
Partie 1: Spécification générique
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 31.140 ISBN 978-2-8322-2777-0
Warning! Make sure that you obtained this publication from an authorized distributor.
Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.
® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale
---------------------- Page: 9 ----------------------
SIST EN 62604-1:2015
– 2 – IEC 62604-1:2015 © IEC 2015
CONTENTS
FOREWORD . 5
1 Scope . 7
2 Normative references . 7
3 Terms, definitions, units and symbols . 8
3.1 Terms and definitions . 8
3.1.1 General terms . 9
3.1.2 Response characteristics related terms . 10
3.1.3 SAW and BAW duplexers related terms . 14
3.2 Units and graphical symbols . 16
4 Order of precedence of documents . 16
5 Preferred values for ratings and characteristics . 16
5.1 General . 16
5.2 Nominal frequency bands . 16
5.3 Operating temperature ranges, in degrees Celsius (°C) . 16
5.4 Climatic category . 17
5.5 Bump severity . 17
5.6 Vibration severity . 17
5.7 Shock severity . 18
5.8 Fine leak rate . 18
6 Marking . 18
6.1 Duplexer marking . 18
6.2 Package marking . 18
7 Quality assessment procedures . 19
7.1 General . 19
7.2 Primary stage of manufacture . 19
7.3 Structurally similar components . 19
7.4 Subcontracting . 19
7.5 Incorporated components . 19
7.6 Manufacturer’s approval . 19
7.7 Approval procedures . 19
7.7.1 General . 19
7.7.2 Capability approval . 19
7.7.3 Qualification approval . 20
7.8 Procedures for capability approval . 20
7.8.1 General . 20
7.8.2 Eligibility for capability approval . 20
7.8.3 Application for capability approval . 20
7.8.4 Granting of capability approval . 20
7.8.5 Capability manual . 20
7.9 Procedures for qualification approval . 20
7.9.1 General . 20
7.9.2 Eligibility for qualification approval . 20
7.9.3 Application for qualification approval . 21
7.9.4 Granting of qualification approval . 21
7.9.5 Quality conformance inspection . 21
7.10 Test procedures . 21
---------------------- Page: 10 ----------------------
SIST EN 62604-1:2015
IEC 62604-1:2015 © IEC 2015 – 3 –
7.11 Screening requirements . 21
7.12 Rework and repair work . 21
7.12.1 Rework . 21
7.12.2 Repair work . 21
7.13 Certified records of released lots . 21
7.14 Validity of release . 21
7.15 Release for delivery . 21
7.16 Unchecked parameters . 21
8 Test and measurement procedures . 22
8.1 General . 22
8.2 Test and measurement conditions . 22
8.2.1 Standard conditions for testing . 22
8.2.2 Precision of measurement . 22
8.2.3 Precautions . 22
8.2.4 Alternative test methods . 23
8.3 Visual inspection . 23
8.3.1 General . 23
8.3.2 Visual test A . 23
8.3.3 Visual test B . 23
8.4 Dimensions test . 23
8.5 Electrical test procedures . 23
8.5.1 S parameters measurement . 23
8.5.2 Intermodulation distortion measurement . 25
8.5.3 Insulation resistance . 25
8.5.4 Voltage proof . 25
8.6 Mechanical and environmental test procedures . 25
8.6.1 Sealing tests (non-destructive) . 25
8.6.2 Soldering (solderability and resistance to soldering heat) (destructive) . 26
8.6.3 Rapid change of temperature: severe shock by liquid immersion (non-
destructive). 26
8.6.4 Rapid change of temperature with prescribed time of transition (non-
destructive). 26
8.6.5 Bump (destructive) . 26
8.6.6 Vibration (destructive). 27
8.6.7 Shock (destructive) . 27
8.6.8 Free fall (destructive) . 27
8.6.9 Acceleration, steady state (non-destructive) . 28
8.6.10 Low air pressure (non-destructive) . 28
8.6.11 Dry heat (non-destructive) . 28
8.6.12 Damp heat, cyclic (destructive) . 28
8.6.13 Cold (non-destructive) . 28
8.6.14 Climatic sequence (destructive) . 28
8.6.15 Damp heat, steady state (destructive) . 29
8.6.16 Salt mist cyclic (destructive) . 29
8.6.17 Immersion in cleaning solvents (non-destructive) . 29
8.6.18 Flammability test (destructive) . 29
8.6.19 Electrostatic discharge (ESD) sensitivity test (destructive) . 29
8.7 Endurance test procedure . 30
Bibliography . 31
---------------------- Page: 11 ----------------------
SIST EN 62604-1:2015
– 4 – IEC 62604-1:2015 © IEC 2015
Figure 1 – FBAR configuration . 9
Figure 2 – SMR configuration . 10
Figure 3 – Frequency response of SAW and BAW duplexers . 15
Figure 4 – S parameters measurement . 24
Table 1 – Frequency allocation of typical UMTS bands . 16
---------------------- Page: 12 ----------------------
SIST EN 62604-1:2015
IEC 62604-1:2015 © IEC 2015 – 5 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
SURFACE ACOUSTIC WAVE (SAW) AND
BULK ACOUSTIC WAVE (BAW) DUPLEXERS
OF ASSESSED QUALITY –
Part 1: Generic specification
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 62604-1 has been prepared by IEC technical committee 49:
Piezoelectric, dielectric and electrostatic devices and associated materials for frequency
control, selection and detection.
NOTE In this standard, SAW and BAW duplexers are treated simultaneously because both duplexers are used in
the same manner especially in mobile phones and have the same requirements of characteristics, test method and
so on.
The text of this standard is based on the following documents:
FDIS Report on voting
49/1143/FDIS 49/1160/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
---------------------- Page: 13 ----------------------
SIST EN 62604-1:2015
– 6 – IEC 62604-1:2015 © IEC 2015
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
A list of all parts in the IEC 62604 series, published under the general title: Surface acoustic
wave (SAW) and bulk acoustic wave (BAW) duplexers of assessed quality, can be found on
the IEC website.
The committee has decided that the contents of this publication will remain unchanged until
the stability date indicated on the IEC website under "http://webstore.iec.ch" in the data
related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
IMPORTANT – The 'colour inside' logo on the cover page of this publication indicates
that it contains colours which are considered to be useful for the correct
understanding of its contents. Users should therefore print this document using a
colour printer.
---------------------- Page: 14 ----------------------
SIST EN 62604-1:2015
IEC 62604-1:2015 © IEC 2015 – 7 –
SURFACE ACOUSTIC WAVE (SAW) AND
BULK ACOUSTIC WAVE (BAW) DUPLEXERS
OF ASSESSED QUALITY –
Part 1: Generic specification
1 Scope
This part of IEC 62604 specifies the methods of test and general requirements for SAW and
BAW duplexers of assessed quality using either capability approval or qualification approval
procedures.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and
are indispensable for its application. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any
amendments) applies.
IEC 60027 (all parts), Letter symbols to be used in electrical technology
IEC 60050 (all parts), International Electrotechnical Vocabulary (available at
www.electropedia.org)
IEC 60068-1:2013, Environmental testing – Part 1: General and guidance
IEC 60068-2-1, Environmental testing – Part 2-1: Tests – Test A: Cold
IEC 60068-2-2, Environmental testing – Part 2-2: Tests – Test B: Dry heat
IEC 60068-2-6, Environmental testing – Part 2-6: Tests – Test Fc: Vibration (sinusoidal)
IEC 60068-2-7, Basic environmental testing procedures – Part 2-7: Tests – Test Ga and
guidance: Acceleration, steady state
IEC 60068-2-13, Basic environmental testing procedures – Part 2-13: Tests – Test M: Low air
pressure
IEC 60068-2-14, Environmental testing – Part 2-14: Tests – Test N: Change of temperature
IEC 60068-2-17:1994, Basic environmental testing procedures – Part 2-17: Tests – Test Q:
Sealing
IEC 60068-2-27, Environmental testing – Part 2-27: Tests – Test Ea and guidance: Shock
IEC 60068-2-30, Environmental testing – Part 2-30: Tests – Test Db: Damp heat, cyclic
(12 h + 12
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.