SIST EN ISO 14323:2006
(Main)Resistance spot welding and projection welds - Destructive testing of welds - Specimen dimensions and procedure for impact shear test and cross-tension testing (ISO 14323:2006)
Resistance spot welding and projection welds - Destructive testing of welds - Specimen dimensions and procedure for impact shear test and cross-tension testing (ISO 14323:2006)
This International Standard covers destructive testing of welds. This International Standard specifies specimen dimensions and testing procedures for impact shear and cross-tension testing of resistance spot and embossed projection welds in overlapping sheets, in any metallic material of thickness 0,5 mm to 4 mm.
Widerstandspunkt- und Buckelschweißen - Zerstörende Prüfung von Schweißverbindungen - Probenabmessungen und Durchführung des Schlagscherzugversuchs und des Schlagkopfzugversuchs (ISO 14323:2006)
Diese Internationale Norm behandelt die zerstörende Prüfung von Schweißverbindungen.
Diese Internationale Norm legt die Probenabmessungen und Prüfverfahren für die Schlagscherzug- und die Schlagkopfzugprüfung von Widerstandspunkt- und geprägten Buckelschweißverbindungen überlappender Bleche aus beliebigem metallischen Werkstoff mit einer Dicke von 0,5 mm bis 4 mm fest.
Soudage par résistance par points et par bossages - Essais destructifs des soudures - Dimensions des éprouvettes et procédure d'essai de cisaillement par choc et d'essai de traction par choc sur éprouvettes en croix (ISO 14323:2006)
L'ISO 14323:2006 traite des essais destructifs des soudures. Elle spécifie les dimensions des éprouvettes et les modes opératoires d'essai de cisaillement par choc et de traction sur éprouvettes en croix des soudures par résistance par points et par bossages de tôles minces, en tout matériau, d'épaisseur de 0,5 mm à 4 mm.
Točkovno in bradavično uporovno varjenje – Porušitveno preskušanje zvarov – Mere vzorcev za udarni strižni in prečni natezni preskus (ISO 14323:2006)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 14323:2006
01-oktober-2006
7RþNRYQRLQEUDGDYLþQRXSRURYQRYDUMHQMH±3RUXãLWYHQRSUHVNXãDQMH]YDURY±
0HUHY]RUFHY]DXGDUQLVWULåQLLQSUHþQLQDWH]QLSUHVNXV ,62
Resistance spot welding and projection welds - Destructive testing of welds - Specimen
dimensions and procedure for impact shear test and cross-tension testing (ISO
14323:2006)
Widerstandspunkt- und Buckelschweißen - Zerstörende Prüfung von
Schweißverbindungen - Probenabmessungen und Durchführung des
Schlagscherzugversuchs und des Schlagkopfzugversuchs (ISO 14323:2006)
Soudage par résistance par points et par bossages - Essais destructifs des soudures -
Dimensions des éprouvettes et procédure d'essai de cisaillement par choc et d'essai de
traction par choc sur éprouvettes en croix (ISO 14323:2006)
Ta slovenski standard je istoveten z: EN ISO 14323:2006
ICS:
25.160.40 Varjeni spoji in vari Welded joints
SIST EN ISO 14323:2006 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 14323:2006
---------------------- Page: 2 ----------------------
SIST EN ISO 14323:2006
EUROPEAN STANDARD
EN ISO 14323
NORME EUROPÉENNE
EUROPÄISCHE NORM
May 2006
ICS 25.160.40
English Version
Resistance spot welding and projection welds - Destructive
testing of welds - Specimen dimensions and procedure for
impact shear test and cross-tension testing (ISO 14323:2006)
Soudage par résistance par points et par bossages - Widerstandspunkt- und Buckelschweißen - Zerstörende
Essais destructifs des soudures - Dimensions des Prüfung von Schweißverbindungen - Probenabmessungen
éprouvettes et procédure d'essai de cisaillement par choc und Durchführung des Schlagscherzugversuchs und des
et d'essai de traction par choc sur éprouvettes en croix Schlagkopfzugversuchs (ISO 14323:2006)
(ISO 14323:2006)
This European Standard was approved by CEN on 9 March 2006.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,
Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2006 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 14323:2006: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 14323:2006
EN ISO 14323:2006 (E)
Foreword
This document (EN ISO 14323:2006) has been prepared by Technical Committee IIW
"International Institute of Welding" in collaboration with Technical Committee CEN/TC 121
"Welding", the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by November 2006, and conflicting national
standards shall be withdrawn at the latest by November 2006.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary,
Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Endorsement notice
The text of ISO 14323:2006 has been approved by CEN as EN ISO 14323:2006 without any
modifications.
2
---------------------- Page: 4 ----------------------
SIST EN ISO 14323:2006
INTERNATIONAL ISO
STANDARD 14323
First edition
2006-05-01
Resistance spot welding and projection
welds — Destructive testing of welds —
Specimen dimensions and procedure for
impact shear test and cross-tension
testing
Soudage par résistance par points et par bossages — Essais
destructifs des soudures — Dimensions des éprouvettes et procédure
d'essai de cisaillement par choc et d'essai de traction par choc sur
éprouvettes en croix
Reference number
ISO 14323:2006(E)
©
ISO 2006
---------------------- Page: 5 ----------------------
SIST EN ISO 14323:2006
ISO 14323:2006(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2006
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2006 – All rights reserved
---------------------- Page: 6 ----------------------
SIST EN ISO 14323:2006
ISO 14323:2006(E)
Contents Page
Foreword. iv
Introduction . v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions. 1
4 Test specimen . 4
5 Test equipment and testing procedure . 6
5.1 General. 6
5.2 Modified pendulum machine . 6
5.3 Drop-weight machine . 8
6 Test report . 12
Annex A (informative) Determination of absorbed energy . 13
Bibliography . 18
© ISO 2006 – All rights reserved iii
---------------------- Page: 7 ----------------------
SIST EN ISO 14323:2006
ISO 14323:2006(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 14323 was prepared by the International Institute of Welding, recognized as an international
standardizing body in the field of welding in accordance with Council Resolution 42/1999.
iv © ISO 2006 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 14323:2006
ISO 14323:2006(E)
Introduction
Requests for official interpretations of provisions in this standard should be made in writing and sent to the
ISO Central Secretariat who will forward them to the IIW Secretariat for an official response.
© ISO 2006 – All rights reserved v
---------------------- Page: 9 ----------------------
SIST EN ISO 14323:2006
---------------------- Page: 10 ----------------------
SIST EN ISO 14323:2006
INTERNATIONAL STANDARD ISO 14323:2006(E)
Resistance spot welding and projection welds — Destructive
testing of welds — Specimen dimensions and procedure for
impact shear test and cross-tension testing
1 Scope
This International Standard covers destructive testing of welds.
This International Standard specifies specimen dimensions and testing procedures for impact shear and
cross-tension testing of resistance spot and embossed projection welds in overlapping sheets, in any metallic
material of thickness 0,5 mm to 4 mm.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 669, Resistance welding — Resistance welding equipment — Mechanical and electrical requirements
ISO 14272, Specimen dimensions and procedure for cross tension testing resistance spot and embossed
projection welds
ISO 14329, Resistance welding — Destructive tests of welds — Failure types and geometric measurements
for resistance spot, seam and projection welds
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 669 and ISO 14329 and the
following apply.
3.1
corona bond
area of the weld at the faying surfaces in which solid-phase bonding has occurred
3.2
impact cross-tension failure energy
failure energy measured in the impact cross-tension test
3.3
impact cross-tension force
maximum force measured in the impact cross-tension test
3.4
impact shear failure energy
failure energy measured in the impact shear test
© ISO 2006 – All rights reserved 1
---------------------- Page: 11 ----------------------
SIST EN ISO 14323:2006
ISO 14323:2006(E)
3.5
impact shear force
maximum force measured in the impact shear test
3.6
interface failure
fracture through the weld (nugget) between the sheets at the plane of the interface
See Figure 1 b).
3.7
nominal weld diameter
diameter of the plug (slug/button) measured at the base of the nugget
See Figure 1 a).
3.8
plug failure
slug/button failure
fracture in the base metal, the heat-affected zone, or in the nugget leaving a plug
See Figure 1 a).
3.9
weld diameter
d
〈interface failure〉 diameter of the fused zone measured at the interface, omitting the corona bond area
See Figure 1 b).
3.10
weld diameter
d
〈partial plug failure〉 mean diameter of the fused zone measured at the interface, omitting the corona bond
area and the maximum diameter of the plug component of the failure
NOTE The minimum diameter of the plug component should be quoted separately [see Figure 1
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.