oSIST prEN 15068:2006

Gas welding equipment - Laboratory measurement of noise emitted by blowpipe for welding, cutting, heating, brazing and soldering - Measurement method

This document specifies a laboratory measurement method of noise emitted by blowpipes used for welding, cutting and allied processes.

Gasschweißgeräte - Labormessungen für von Brennern für Schweißen, Schneiden, Wärmen, Hartlöten und Weichlöten erzeugte Geräusche - Messverfahren

Dieses Dokument legt Labormessverfahren für die Geräuschemission von Brennern für Schweißen,
Schneiden und verwandte Verfahren fest.

Matériel de soudage aux gaz - Mesurage en laboratoire du bruit émis par les chalumeaux destinés au soudage, brasage, coupage et chauffage - Méthode de mesurage

Le présent document spécifie une méthode de mesurage en laboratoire du bruit émis par les chalumeaux utilisés pour le soudage, le coupage et techniques connexes.

Oprema za plamensko varjenje – Laboratorijska meritev hrupa, ki ga oddajajo gorilniki za varjenje, rezanje, segrevanje, trdo in mehko spajkanje – Merilna metoda

General Information

• Status: Not Published
• ICS: 17.140.20 - Noise emitted by machines and equipment
• ICS: 25.160.30 - Welding equipment
• Technical Committee: VAR - Welding
• Current Stage: 98 - Abandoned project (Adopted Project)
• Start Date: 04-Nov-2013
• Due Date: 09-Nov-2013
• Completion Date: 08-Jan-2014
• Ref Project: prEN 15068 - Gas welding equipment - Laboratory measurement of noise emitted by blowpipe for welding, cutting, heating, brazing and soldering - Measurement method

Standards Content (Sample)

SLOVENSKI STANDARD
oSIST prEN 15068:2006
01-december-2006
Oprema za plamensko varjenje – Laboratorijska meritev hrupa, ki ga oddajajo
gorilniki za varjenje, rezanje, segrevanje, trdo in mehko spajkanje – Merilna
metoda
Gas welding equipment - Laboratory measurement of noise emitted by blowpipe for
welding, cutting, heating, brazing and soldering - Measurement method
Gasschweißgeräte - Labormessungen für von Brennern für Schweißen, Schneiden,
Wärmen, Hartlöten und Weichlöten erzeugte Geräusche - Messverfahren
Matériel de soudage aux gaz - Mesurage en laboratoire du bruit émis par les
chalumeaux destinés au soudage, brasage, coupage et chauffage - Méthode de
mesurage
Ta slovenski standard je istoveten z: prEN 15068
ICS:
17.140.20 Emisija hrupa naprav in Noise emitted by machines
opreme and equipment
25.160.30 Varilna oprema Welding equipment
oSIST prEN 15068:2006 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 15068:2006

---------------------- Page: 2 ----------------------
oSIST prEN 15068:2006
EUROPEAN STANDARD
DRAFT
prEN 15068
NORME EUROPÉENNE
EUROPÄISCHE NORM
September 2006
ICS

English Version
Gas welding equipment - Laboratory measurement of noise
emitted by blowpipe for welding, cutting, heating, brazing and
soldering - Measurement method
Matériel de soudage aux gaz - Mesurage en laboratoire du Gasschweißgeräte - Labormessungen für von Brennern für
bruit émis par les chalumeaux destinés au soudage, Schweißen, Schneiden, Wärmen, Hartlöten und Weichlöten
brasage, coupage et chauffage - Méthode de mesurage erzeugte Geräusche - Messverfahren
This draft European Standard is submitted to CEN members for second enquiry. It has been drawn up by the Technical Committee
CEN/TC 121.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CEN member into its own language and notified to the Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,
Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2006 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 15068:2006: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
oSIST prEN 15068:2006
prEN 15068:2006 (E)
Contents Page
Foreword.3
1 Scope .4
2 Normative references .4
3 Terms and definitions .4
4 Measurement conditions .4
5 Procedure .6
6 Test results.6
7 Test report .6

2

---------------------- Page: 4 ----------------------
oSIST prEN 15068:2006
prEN 15068:2006 (E)
Foreword
This document (prEN 15068:2006) has been prepared by Technical Committee CEN/TC 121 “Welding”, the
secretariat of which is h
...

SLOVENSKI oSIST prEN 15068:2005

PREDSTANDARD
januar 2005
Naprave za plamensko varjenje - Laboratorijsko merjenje emisije hrupa pri
gorilnikih za varjenje, rezanje, segrevanje ter trdo in mehko spajkanje –
Merilna metoda
(istoveten prEN 15068:2004)
Gas welding equipment - Laboratory measurement of noise emitted by blowpipes
for welding, cutting, heating, brazing and soldering - Measurement method
ICS 17.140.20; 25.160.30 Referenčna številka
oSIST prEN 15068:2005(en)
©  Standard je založil in izdal Slovenski inštitut za standardizacijo. Razmnoževanje ali kopiranje celote ali delov tega dokumenta ni dovoljeno

---------------------- Page: 1 ----------------------
EUROPEAN STANDARD
DRAFT
prEN 15068
NORME EUROPÉENNE
EUROPÄISCHE NORM
October 2004
ICS
English version
Gas welding equipment - Laboratory measurement of noise
emitted by blowpipes for welding, cutting, heating, brazing and
soldering - Measurement method
Matériel de soudage aux gaz - Mesurage en laboratoire du Gasschweißgeräte - Labormessungen für von Brennern für
bruit émis par les chalumeaux destinés au soudage, Schweißen, Schneiden, Wärmen, Hartlöten und Weichlöten
brasage, coupage et chauffage - Méthode de mesurage erzeugten Geräusche - Messmethode
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 121.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CEN member into its own language and notified to the Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2004 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 15068:2004: E
worldwide for CEN national Members.

---------------------- Page: 2 ----------------------
prEN 15068:2004 (E)
Contents Page
Foreword.3
Introduction .4
1 Scope .5
2 Normative references .5
3 Terms and definitions .5
4 Blowpipes classification .5
5 Measurement conditions .6
6 Procedure .8
7 Expression of results .8
8 Test report .8
Annex A (informative) Estimation by calculation of noise received by a person.9

2

---------------------- Page: 3 ----------------------
prEN 15068:2004 (E)
Foreword
This document (prEN 15068:2004) has been prepared by Technical Committee CEN/TC 121 “Welding”, the
secretariat of which is held by DIN.
This document is currently submitted to the CEN Enquiry.
3

---------------------- Page: 4 ----------------------
prEN 15068:2004 (E)
Introduction
Improvement of working conditions is a permanent concern in industry. Noise is a main part of it.
It is not possible
...