SIST EN 60684-3-205:2011
Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 205: Heat-shrinkable chlorinated polyolefin sleeving, flame retarded, nominal shrink ratio 1,7:1 and 2:1
Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 205: Heat-shrinkable chlorinated polyolefin sleeving, flame retarded, nominal shrink ratio 1,7:1 and 2:1
This part of IEC 60684 gives the requirements for one type of heat-shrinkable chlorinated polyolefin sleeving, flame retarded, nominal shrink ratio 1,7:1 and 2:1 for use at temperatures up to 120 °C. These sleevings are normally supplied with internal diameters up to 102 mm, and the standard colour is black. Sizes or colours other than those specifically listed in this standard may be available as custom items. These items shall be considered to comply with this standard if they comply with the property requirements listed in Tables 3, 4 and 5 except for dimensions and mass, and Table 6, as applicable. Materials which conform to this specification meet established levels of performance. However, the selection of a material by a user for a specific application should be based on the actual requirements necessary for adequate performance in that application and not based on this specification alone
Isolierschläuche - Teil 3: Anforderungen für einzelne Schlauchtypen - Blatt 205: Wärmeschrumpfschläuche aus chloriertem Polyolefin, flammwidrig, nominales Schrumpfverhältnis 1,7:1 und 2:1
Gaines isolantes souples - Partie 3: Spécifications pour types particuliers de gaines - Feuille 205: Gaines thermorétractables en polyoléfine chlorée, retardées à la flame, rapport de rétreint nominal de 1,7:1 et 2:1
La CEI 60684-3-205:2011 donne les exigences pour un type de gaine thermorétractable en polyoléfine chlorée, retardée à la flamme, rapport de rétreint nominal de 1,7:1 et 2:1, pour un usage à des températures allant jusqu'à 120 °C.
Gibke izolacijske cevi - 3. del: Specifikacije za posamezne vrste cevi - 205. list: Toplotno skrčljive klorirane poliolefinske cevi, ognjevarne, z nazivnima skrčnima razmerjema 1,7:1 in 2:1
Ta del IEC 60684 podaja zahteve za en tip toplotno skrčljivih kloriranih poliolefinskih cevi, ognjevarnih, z nazivnima skrčnima razmerjema 1,7 : 1 in 2 : 1 za uporabo pri temperaturah do 120 °C. Te cevi se običajno dobavljajo z notranjimi premeri do 102 mm in v standardni črni barvi. Velikosti ali barve, ki niso navedene v tem standardu, so lahko na voljo na zahtevo. Ti predmeti so skladni s tem standardom, če izpolnjujejo zahteve glede lastnosti, navedene v preglednicah 3, 4 in 5, razen mer in mase, ter v preglednici 6, kot ustreza. Materiali, skladni s to specifikacijo, ustrezajo vzpostavljenim ravnem delovanja. Vendar mora uporabnik material za določeno uporabo izbrati na podlagi dejanskih zahtev za ustrezno delovanje pri taki uporabi, ne le na podlagi same specifikacije.
General Information
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Isolierschläuche - Teil 3: Anforderungen für einzelne Schlauchtypen - Blatt 205: Wärmeschrumpfschläuche aus chloriertem Polyolefin, flammwidrig, nominales Schrumpfverhältnis 1,7:1 und 2:1Gaines isolantes souples - Partie 3: Spécifications pour types particuliers de gaines - Feuille 205: Gaines thermorétractables en polyoléfine chlorée, retardées à la flame, rapport de rétreint nominal de 1,7:1 et 2:1Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 205: Heat-shrinkable chlorinated polyolefin sleeving, flame retarded, nominal shrink ratio 1,7:1 and 2:129.035.20PDWHULDOLPlastics and rubber insulating materialsICS:Ta slovenski standard je istoveten z:EN 60684-3-205:2011SIST EN 60684-3-205:2011en,fr,de01-oktober-2011SIST EN 60684-3-205:2011SLOVENSKI
STANDARD
SIST EN 60684-3-205:2011
EUROPEAN STANDARD EN 60684-3-205 NORME EUROPÉENNE
EUROPÄISCHE NORM July 2011
CENELEC European Committee for Electrotechnical Standardization Comité Européen de Normalisation Electrotechnique Europäisches Komitee für Elektrotechnische Normung
Management Centre: Avenue Marnix 17, B - 1000 Brussels
© 2011 CENELEC -
All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60684-3-205:2011 E
ICS 29.035.20
English version
Flexible insulating sleeving -
Part 3: Specifications for individual types of sleeving -
Sheet 205: Heat-shrinkable chlorinated polyolefin sleeving, flame retarded, nominal shrink ratio 1,7:1 and 2:1 (IEC 60684-3-205:2011)
Gaines isolantes souples -
Partie 3: Spécifications pour types particuliers de gaines -
Feuille 205: Gaines thermorétractables en polyoléfine chlorée, retardées à la flamme, rapport de rétreint nominal de 1,7:1 et 2:1(CEI 60684-3-205:2011)
Isolierschläuche -
Teil 3: Anforderungen für einzelne Schlauchtypen -
Blatt 205: Wärmeschrumpfschläuche aus chloriertem Polyolefin, flammwidrig, nominales Schrumpfverhältnis 1,7:1 und 2:1 (IEC 60684-3-205:2011)
This European Standard was approved by CENELEC on 2011-07-26. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom.
SIST EN 60684-3-205:2011
EN 60684-3-205:2011 - 2 - Foreword The text of document 15/626/FDIS, future edition 1 of IEC 60684-3-205, prepared by IEC TC 15, Solid electrical insulating materials, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 60684-3-205 on 2011-07-26. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and CENELEC shall not be held responsible for identifying any or all such patent rights. The following dates were fixed: – latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement
(dop)
2012-04-26 – latest date by which the national standards conflicting
with the EN have to be withdrawn
(dow)
2014-07-26 Annex ZA has been added by CENELEC. __________ Endorsement notice The text of the International Standard IEC 60684-3-205:2011 was approved by CENELEC as a European Standard without any modification. __________ SIST EN 60684-3-205:2011
- 3 - EN 60684-3-205:2011 Annex ZA
(normative)
Normative references to international publications with their corresponding European publications
The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
NOTE
When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies.
Publication Year Title EN/HD Year
IEC 60684-1 2003 Flexible insulating sleeving -
Part 1: Definitions and general requirements EN 60684-1 2003
IEC 60684-2 + corr. December
+ A1 + A2 1997 1997 2003 2005 Flexible insulating sleeving -
Part 2: Methods of test EN 60684-2 + A1 + A2 1997 2003 2005
IEC 60757 1983 Code for designation of colours HD 457 S1 1985
ISO 846 1997 Plastics - Evaluation of the action of microorganisms EN ISO 846 1997
ISO 1817 2005 Rubber, vulcanized - Determination of the effect of liquids - -
SIST EN 60684-3-205:2011
SIST EN 60684-3-205:2011
IEC 60684-3-205 Edition 1.0 2011-06 INTERNATIONAL STANDARD NORME INTERNATIONALE Flexible insulating sleeving –
Part 3: Specifications for individual types of sleeving – Sheet 205:
Heat-shrinkable chlorinated polyolefin sleeving, flame retarded, nominal shrink ratio 1,7:1 and 2:1
Gaines isolantes souples –
Partie 3: Spécifications pour types particuliers de gaines – Feuille 205: Gaines thermorétractables en polyoléfine chlorée, retardées à la flamme, rapport de rétreint nominal de 1,7:1 et 2:1
INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE M ICS 29.035.20 PRICE CODE CODE PRIX ISBN 978-2-88912-546-3
® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale ®
SIST EN 60684-3-205:2011
– 2 – 60684-3-205 © IEC:2011 CONTENTS FOREWORD . 3 INTRODUCTION . 5 1 Scope . 6 2 Normative references. 6 3 Designation . 7 4 Conditions of test . 7 5 Requirements . 7 6 Sleeving conformance. 7 7 Breakdown voltage . 10
Table 1 – Dimensional and mass requirements (nominal shrink ratio 1,7:1) . 8 Table 2 – Dimensional and mass requirements (nominal shrink ratio 2:1) . 8 Table 3 – Property requirements . 9 Table 4 – Requirements for breakdown voltage . 11 Table 5 – Resistance to selected fluids . 11 Table 6 – Additional property requirements . 12
SIST EN 60684-3-205:2011
60684-3-205 © IEC:2011 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION ___________
FLEXIBLE INSULATING SLEEVING –
Part 3: Specifications for individual types of sleeving –
Sheet 205:
Heat-shrinkable chlorinated polyolefin sleeving,
flame retarded, nominal shrink ratio 1,7:1 and 2:1
FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publicatio
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.