SIST EN ISO 18739:2016

Dentistry - Vocabulary of process chain for CAD/CAM systems (ISO 18739:2016)

This International Standard specifies terms, synonyms for terms and definitions used in the process chain for CAD/CAM systems in dentistry.

Zahnheilkunde - Vokabular der Prozesskette für CAD/CAM-Systeme (ISO 18739:2016)

Diese Internationale Norm legt Begriffe, Synonyme für Begriffe und Definitionen fest, die in der Prozesskette für CAD/CAM-Systeme in der Zahnheilkunde verwendet werden.

Médecine bucco-dentaire - Vocabulaire pour CAD/CAM système (ISO 18739:2016)

ISO 18739:2016 spécifie les termes, leurs synonymes, et les définitions utilisés dans la chaîne de procédé applicable aux systèmes dentaires de CFAO.

Zobozdravstvo - Slovar procesa za sisteme CAD/CAM (ISO 18739:2016)

Ta mednarodni standard določa izraze, sopomenke za izraze in definicije, ki se uporabljajo v procesu za sisteme CAD/CAM v zobozdravstvu.

General Information

• Status: Published
• Public Enquiry End Date: 29-Apr-2015
• Publication Date: 19-May-2016
• ICS: 01.040.11 - Health care technology (Vocabularies)
• ICS: 11.060.01 - Dentistry in general
• Technical Committee: VAZ - Healthcare
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 14-Apr-2016
• Due Date: 19-Jun-2016
• Completion Date: 20-May-2016
• Ref Project: EN ISO 18739:2016 - Dentistry - Vocabulary of process chain for CAD/CAM systems (ISO 18739:2016)

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 18739:2016
01-junij-2016
Zobozdravstvo - Slovar procesa za sisteme CAD/CAM (ISO 18739:2016)
Dentistry - Vocabulary of process chain for CAD/CAM systems (ISO 18739:2016)
Zahnheilkunde - Vokabular der Prozesskette für CAD/CAM-Systeme (ISO 18739:2016)
Médecine bucco-dentaire - Vocabulaire pour CAD/CAM système (ISO 18739:2016)
Ta slovenski standard je istoveten z: EN ISO 18739:2016
ICS:
01.040.11 Zdravstveno varstvo Health care technology
(Slovarji) (Vocabularies)
11.060.01 Zobozdravstvo na splošno Dentistry in general
SIST EN ISO 18739:2016 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 18739:2016

---------------------- Page: 2 ----------------------

SIST EN ISO 18739:2016


EN ISO 18739
EUROPEAN STANDARD

NORME EUROPÉENNE

April 2016
EUROPÄISCHE NORM
ICS 11.060.01
English Version

Dentistry - Vocabulary of process chain for CAD/CAM
systems (ISO 18739:2016)
Médecine bucco-dentaire - Vocabulaire de la chaîne de Zahnheilkunde - Vokabular der Prozesskette für
procédé applicable aux systèmes de CFAO (ISO CAD/CAM-Systeme (ISO 18739:2016)
18739:2016)
This European Standard was approved by CEN on 20 February 2016.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2016 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 18739:2016 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 18739:2016
EN ISO 18739:2016 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------

SIST EN ISO 18739:2016
EN ISO 18739:2016 (E)
European foreword
This document (EN ISO 18739:2016) has been prepared by Technical Committee ISO/TC 106
"Dentistry" in collaboration with Technical Committee CEN/TC 55 “Dentistry” the secretariat of which
is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by October 2016, and conflicting national standards shall
be withdrawn at the latest by October 2016.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent
rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 18739:2016 has been approved by CEN as EN ISO 18739:2016 without any modification.
3

---------------------- Page: 5 ----------------------

SIST EN ISO 18739:2016

---------------------- Page: 6 ----------------------

SIST EN ISO 18739:2016
INTERNATIONAL ISO
STANDARD 18739
First edition
2016-03-01
Dentistry — Vocabulary of process
chain for CAD/CAM systems
Médecine bucco-dentaire — Vocabulaire de la chaîne de procédé
applicable aux systèmes de CFAO
Reference number
ISO 18739:2016(E)
©
ISO 2016

---------------------- Page: 7 ----------------------

SIST EN ISO 18739:2016
ISO 18739:2016(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2016, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. [phone]
Fax [phone]
[e-mail]
www.iso.org
ii © ISO 2016 – All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 18739:2016
ISO 18739:2016(E)

Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
3.1 Process step terms . 1
3.2 Measurement and calibration terms . 6
Annex A (informative) Flow chart of process chain for CAD/CAM-systems .9
Index  .10
© ISO 2016 – All rights reserved iii

---------------------- Page: 9 ----------------------

SIST EN ISO 18739:2016
ISO 18739:2016(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2. www.iso.org/directives
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received. www.iso.org/patents
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical
Barriers to Trade (TBT), see the following URL: Foreword - Supplementary information
The committee responsible for this document is ISO/TC 106, Dentistry, Subcommittee SC 9, CAD/CAM-
Systems.
iv © ISO 2016 – All rights reserved

---------------------- Page: 10 ----------------------

SIST EN ISO 18739:2016
ISO 18739:2016(E)

Introduction
Terms and designations for individual system parts and process steps used in product descriptions and
instructions for use provided by the manufacturers of dental CAD/CAD systems differ from each other,
thus creating confusion among dentists and dental technicians. In order to overcome these ambiguities,
it was decided to prepare an International Standard for terminology used in the process chain for
CAD/CAM systems.
For the purposes of illustrating the logic sequence of the process chain for CAD/CAM systems, a flow
chart of this process chain is shown in Annex A.
© ISO 2016 – All rights reserved v

---------------------- Page: 11 ----------------------

SIST EN ISO 18739:2016

---------------------- Page: 12 ----------------------

SIST EN ISO 18739:2016
INTERNATIONAL STANDARD ISO 18739:2016(E)
Dentistry — Vocabulary of process chain for CAD/CAM
systems
1 Scope
This International Standard specifies terms, synonyms for terms and definitions used in the process
chain for CAD/CAM systems in dentistry.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
ISO 1942, Dentistry — Vocabulary
ISO 5725-1, Accuracy (trueness and precision) of measurement methods and results — Part 1: General
principles and definitions
ISO 16443, Dentistry — Vocabulary for dental implants systems and related procedure
ISO/ASTM 52900, Additive manufacturing — General principles — Terminology
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 1942, ISO 5725-1, ISO 16443,
ISO/ASTM 52900 and the following apply.
NOTE In the following, first the preferred term and then the synonyms which have been in use so far are
given. For the future it is recommended to use the preferred terms instead of the synonyms.
3.1 Process step terms
3.1.1
3D data acquisition
three dimensional data acquisition
3D digitization and generation of a digital data set
3.1.2
3D data acquisition system
three dimensional data acquisition system
hardware and software used for 3D data acquisition
3.1.3
3D scanning
3D digitizing
raw data acquisition
method of acquiring the shape and size of an object as a 3-dimensional representation by recording
x,y,z coordinates on the objects surface and through software the collection of points is converted into
digital data
Note 1 to entry: This collection of data via the scanning process creates a raw data set (3.1.14).
© ISO 2016 – All rights reserved 1

---------------------- Page: 13 ----------------------

SIST EN ISO 18739:2016
ISO 18739:2016(E)

Note 2 to entry: Typical scanning methods use some amount of automation, coupled with a touch probe or an
optical sensor, or other device.
[SOURCE: ISO/ASTM 52900:2015, definition 2.4.1, modified]
3.1.4
additive manufacturing
AM
process of joining materials to make parts from 3D model data, usually layer upon layer, as opposed to
subtractive manufacturing and formative manufacturing methodologies
[SOURCE: ISO/ASTM 52900:2015, definition 2.1.2, modified]
3.1.5
artifact
any undesired alteration of data introduced in a digital process by an involved technique and/or
technology
3.1.6
CAD
computer-aided design
hardware and software supporting the designing process
Note 1 to entry: The acronym CAD is commonly used as preferred term.
3.1.7
CAD data
design data set
result of the CAD process (3.1.8) gained by manipulating the model data set for the purposes of transfer
to the CAM system
3.1.8
CAD process
design process (DEPRECATED)
process of generating design data sets
3.1.9
CAD software
design system
system for the generation of a design data set
3.1.10
CAM
computer-aided manufacturing
hardware and software supporting the manufacturing process
Note 1 to entry: The acronym CAM is commonly used as preferred term.
3.1.11
CAM system
manufacturing system
digitally controlled system for the manufacture of CAD/CAM dental restorations
EXAMPLE Milling machine, CAM software.
3.1.12
CAM software
software used for manipulating design data for manufacturing
EXAMPLE Software for the calculation of milling paths.
2 © ISO 2016 – All rights reserved

---------------------- Page: 14 ----------------------

SIST EN ISO 18739:2016
ISO 18739:2016(E)

3.1.13
data record
one or more data items treated as a unit within a data set
3.1.14
data set
complete numerical description
EXAMPLE Raw data set (dot model), digitization data set (manipulated raw data set), surface model, facet
model or volume model.
Note 1 to entry: Raw data set is obtained by processing scanning data.
3.1.15
data structure
defined format interrelating the data (records) in the data set
3.1.16
dental CAD/CAM system
a set of hardware, software, materials, and devices, used to fabricate dental restorations
Note 1 to entry: Hardware and software are used for data acquisition, design and manufacturing.
3.1.17
dental CAD/CAM restoration
dental restoration (3.1.18) produced by a dental CAD/CAM system
3.1.18
dental restoration
any kind of restoration which replaces intra-oral hard and/or soft tissues
3.1.19
design data manipulation process
CAD data manipulation process
process of generating the manufacturing data set
EXAMPLE Tooth path generation process.
3.1.20
digital impression
acquisition of a data set with the numerical 3D-representation of the surfaces from the patient directly
3.1.21
digitizing device
hardware for com
...