iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

oSIST prEN 12900:2024

(Main)

Refrigerant compressors - Rating conditions, tolerances and presentation of performance data

Refrigerant compressors - Rating conditions, tolerances and presentation of performance data

This document specifies the rating conditions, tolerances and the method of presenting performance data of refrigerant compressors.
This document is applicable to single stage compressor and two stage compressor data with or without an additional intermediate pressure inlet.
The performance data of compressors used with R-744 in transcritical operation are covered in this document.
The data relating to the refrigerating capacity, heating capacity and power absorbed include requirements for part load operation where applicable. Presenting performance in this way enables a comparison of different compressors.

Kältemittel-Verdichter - Nennbedingungen, Toleranzen und Darstellung von Leistungsdaten

Dieses Dokument legt die Nennbedingungen, Toleranzen und die Darstellung der Leistungsdaten von Kältemittel-Verdichtern fest.
Dieses Dokument gilt für Daten von einstufigen und zweistufigen Verdichter mit oder ohne zusätzlichen Mitteldruck-Eintritt.
Die Leistungsdaten von Verdichtern, bei denen R 744 im transkritischen Betrieb zur Anwendung kommt, werden von diesem Dokument abgedeckt.
Die Daten beziehen sich auf die Kälteleistung, die Heizleistung und die Leistungsaufnahme und schließen den Teillastbetrieb ein, sofern zutreffend. Diese Darstellung der Leistung ermöglicht den Vergleich verschiedener Verdichter.

Compresseurs pour fluides frigorigènes - Détermination des caractéristiques, tolérances et présentation des données de performance

Le présent document spécifie les conditions de détermination des caractéristiques, les tolérances et le mode de présentation des données de performance, applicables aux compresseurs pour fluides frigorigènes.
Le présent document s’applique aux données de compresseurs mono-étagés et aux compresseurs bi-étagés, avec ou sans entrée de pression intermédiaire supplémentaire.
Les données de performance des compresseurs utilisés avec du R-744 en fonctionnement transcritique sont couvertes dans le présent document.
Les données relatives à la puissance frigorifique, à la puissance calorifique et à la puissance absorbée comprennent les exigences relatives au fonctionnement en charge partielle, quand cela est applicable. Cette manière de présenter les performances permet la comparaison de différents compresseurs.

Kompresorji za hladilne tekočine - Pogoji določanja nazivne moči, toleranc in predstavitev tehničnih karakteristik

General Information

Status
Not Published
Public Enquiry End Date
29-Feb-2024
ICS
23.140 - Compressors and pneumatic machines
27.200 - Refrigerating technology
Technical Committee
OGS - Heating for buildings
Current Stage
4020 - Public enquire (PE) (Adopted Project)
Start Date
21-Dec-2023
Due Date
09-May-2024
Directive
206/2012 - Commission Regulation (EU) No 206/2012 of 6 March 2012 implementing Directive 2009/125/EC of the European Parliament and of the Council with regard to ecodesign requirements for air conditioners and comfort fans
Mandate
M/488 - Mandate to CEN, CENELEC and ETSI in the field of air conditioners and comfort fans
Ref Project
prEN 12900 - Refrigerant compressors - Rating conditions, tolerances and presentation of performance data

Relations

Replaces
SIST EN 12900:2013 - Refrigerant compressors - Rating conditions, tolerances and presentation of manufacturer's performance data
Effective Date
14-Apr-2021

Buy Standard

prEN 12900:2024prEN 12900:2024
PreviousNext
Draft
prEN 12900:2024
English language
19 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
oSIST prEN 12900:2024
01-februar-2024
Nadomešča:
SIST EN 12900:2013
Kompresorji za hladilne tekočine - Pogoji določanja nazivne moči, toleranc in
predstavitev tehničnih karakteristik
Refrigerant compressors - Rating conditions, tolerances and presentation of
performance data
Kältemittel-Verdichter - Nennbedingungen, Toleranzen und Darstellung von
Leistungsdaten
Compresseurs pour fluides frigorigènes - Détermination des caractéristiques, tolérances
et présentation des données de performance
Ta slovenski standard je istoveten z: prEN 12900
ICS:
23.140 Kompresorji in pnevmatični Compressors and pneumatic
stroji machines
27.200 Hladilna tehnologija Refrigerating technology
oSIST prEN 12900:2024 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 12900:2024

---------------------- Page: 2 ----------------------
oSIST prEN 12900:2024


DRAFT
EUROPEAN STANDARD
prEN 12900
NORME EUROPÉENNE

EUROPÄISCHE NORM

December 2023
ICS 23.140; 27.200 Will supersede EN 12900:2013
English Version

Refrigerant compressors - Rating conditions, tolerances
and presentation of performance data
Compresseurs pour fluides frigorigènes - Conditions de Kältemittel-Verdichter - Nennbedingungen, Toleranzen
détermination des caractéristiques, tolérances et und Darstellung von Leistungsdaten
présentation des performances par le fabricant
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 113.

If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 12900:2023 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
oSIST prEN 12900:2024
prEN 12900:2023 (E)
Contents Page
European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Rating conditions . 8
4.1 General . 8
4.2 Ambient temperature around the compressor . 8
4.3 Subcooling .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN 13771-2:2018(Main)
Compressors and condensing units for refrigeration - Performance testing and test methods - Part 2: Condensing units
EN 13771-2:2017

This European Standard applies only to condensing units for refrigeration and describes a number of selected performance test methods. These methods provide sufficiently accurate results for the determination of the refrigerating capacity, power absorbed, refrigerant mass flow and the coefficient of performance.
This European Standard applies only to performance tests conducted at the manufacturer's works or wherever the instrumentation and load stability for testing to the accuracy required is available.

  • Standard
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 13771-1:2017(Main)
Compressors and condensing units for refrigeration - Performance testing and test methods - Part 1: Refrigerant compressors
EN 13771-1:2016

This part of this European Standard applies only to refrigerant compressors and describes a number of selected performance test methods. These methods provide sufficiently accurate results for the determination of the refrigerating capacity, power absorbed, refrigerant mass flow, isentropic efficiency and the coefficient of performance. This standard applies only to performance tests conducted at the manufacturer's works or wherever the equipment for testing to the accuracy required is available.
The type of measuring instrument and the allowable uncertainty within which measurements shall be made are listed in normative Aannex A.

  • Standard
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 12900:2013(Main)
Refrigerant compressors - Rating conditions, tolerances and presentation of manufacturer's performance data
EN 12900:2013

This European Standard specifies the rating conditions, tolerances and the method of presenting manufacturer’s data for positive displacement refrigerant compressors. These include single stage compressors and single and two stage compressors using a means of fluid subcooling. This is required so that a comparison of different refrigerant compressors can be made. The data relate to the refrigerating capacity and power absorbed and include requirements for part-load operation where applicable.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 13771-2:2018(Main)
Compressors and condensing units for refrigeration - Performance testing and test methods - Part 2: Condensing units
EN 13771-2:2017

This European Standard applies only to condensing units for refrigeration and describes a number of selected performance test methods. These methods provide sufficiently accurate results for the determination of the refrigerating capacity, power absorbed, refrigerant mass flow and the coefficient of performance.
This European Standard applies only to performance tests conducted at the manufacturer's works or wherever the instrumentation and load stability for testing to the accuracy required is available.

  • Standard
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 13771-1:2017(Main)
Compressors and condensing units for refrigeration - Performance testing and test methods - Part 1: Refrigerant compressors
EN 13771-1:2016

This part of this European Standard applies only to refrigerant compressors and describes a number of selected performance test methods. These methods provide sufficiently accurate results for the determination of the refrigerating capacity, power absorbed, refrigerant mass flow, isentropic efficiency and the coefficient of performance. This standard applies only to performance tests conducted at the manufacturer's works or wherever the equipment for testing to the accuracy required is available.
The type of measuring instrument and the allowable uncertainty within which measurements shall be made are listed in normative Aannex A.

  • Standard
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 12900:2013(Main)
Refrigerant compressors - Rating conditions, tolerances and presentation of manufacturer's performance data
EN 12900:2013

This European Standard specifies the rating conditions, tolerances and the method of presenting manufacturer’s data for positive displacement refrigerant compressors. These include single stage compressors and single and two stage compressors using a means of fluid subcooling. This is required so that a comparison of different refrigerant compressors can be made. The data relate to the refrigerating capacity and power absorbed and include requirements for part-load operation where applicable.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 12693:2008(Main)
Refrigerating systems and heat pumps - Safety and environmental requirements - Positive displacement refrigerant compressors
EN 12693:2008

This standard applies to positive displacement refrigerant compressors for stationary and mobile refrigerating systems and heat pumps defined in 3.1, hereafter called compressors.
It applies for compressors used in commercial and industrial appliances and with electrical energy supply including integral motors, up to 1 000 VAC and 1 500 VDC.
It applies to open drive, semi hermetic and hermetic motor compressors, which contain a positive compression function
This standard is not applicable to:
-   compressors used in household appliance for which EN 60335-2-34 applies;
-   compressors using water or air as refrigerant.
This standard does not deal with requirements for vibration and noise.
NOTE   Noise emission depends on the complete installation of the built-in compressors and the corresponding operating conditions.
For semi-hermetic and open drive compressors which include moving parts and for which the external envelope is primarily designed for mechanical loads, thermal loads (to limit the possible deformation due to temperature), stiffness of the structure (external mechanical loads and weight of the equipment), taking into account established safe industrial practice, it is considered that pressure is not a significant design factor.
Attached parts covering other functions e.g. oil separators, oil coolers, suction accumulators shall comply to EN 14276-1 or EN 13445-6 (cast iron) or prEN 13445-8:2003 (aluminium) or showing compliance to the relevant European requirements. This applies also to shells for hermetic compressors either welded or with any kind of permanent joint.
Requirements for compressors used in explosive atmospheres are not covered by this standard.
NOTE   For further guidance see EN 13463-1.
This standard deals with all significant hazards, hazardous situations and events relevant to compressors, when they are used as indented and under conditions for misuse which are reasonably foreseeable by the manufacturer (see Clause 4).
This standard

  • Standard
    65 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
oSIST prEN 12693:2023(Main)
Refrigerating systems and heat pumps - Safety and environmental requirements - Positive displacement refrigerant compressors
prEN 12693

This European Standard applies to positive displacement refrigerant compressors for stationary and mobile refrigerating systems and heat pumps defined in 3.1, hereafter called compressors.
It applies for compressors used in commercial and industrial appliances and with electrical energy supply including integral motors, up to 1 000 VAC and 1 500 VDC.
It applies to open drive, semi hermetic and hermetic motor compressors, which contain a positive compression function.
This standard is not applicable to:
-   compressors used in household appliance for which EN 60335 2 34 applies;
-   compressors using water or air as refrigerant.
This European Standard does not deal with requirements for vibration and noise.
NOTE 1   Compressors for automotive comfort air conditioning systems can be developed according e.g. SAE J 639.
NOTE 2   Noise emission depends on the complete installation of the built-in compressors and the corresponding operating conditions.
For semi-hermetic and open drive compressors which include moving parts and for which the external envelope is primarily designed for mechanical loads, thermal loads (to limit the possible deformation due to temperature), stiffness of the structure (external mechanical loads and weight of the equipment), taking into account established safe industrial practice, it is considered that pressure is not a significant design factor.
Attached parts covering other functions e.g. oil separators, oil coolers, suction accumulators should comply to EN 14276 1 or EN 13445 6 (cast iron) or EN 13445 8 (aluminium) or showing compliance to the relevant European requirements. This applies also to shells for hermetic compressors either welded or with any kind of permanent joint.
Requirements for compressors used in explosive atmospheres are not covered by this standard.
NOTE 3   For further guidance see EN 13463-1.
This European Standard deals with all significant hazards, hazardous situations and events relevant to compressors, when they are used as intended and under conditions for misuse which are reasonably foreseeable by the manufacturer (see Clause 4).
This European Standard specifies safety requirements for the design, construction, manufacture and testing, documentation and marking of compressors, including integral accessories, e.g. shut-off valve, if necessary.
The requirements in this standard take account of the intended use, as defined in EN ISO 12100:2010, 3.12.
This standard relates to the compressor itself which is to be incorporated in a refrigerating system.
This standard is not applicable to compressors as defined in the scope which are manufactured before the date of publication as EN.

  • Draft
    81 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
oSIST prEN 12693:2016(Main)
Refrigerating systems and heat pumps - Safety and environmental requirements - Positive displacement refrigerant compressors
prEN 12693

This European Standard applies to positive displacement refrigerant compressors for stationary and mobile refrigerating systems and heat pumps defined in 3.1, hereafter called compressors.
It applies for compressors used in commercial and industrial appliances and with electrical energy supply including integral motors, up to 1 000 VAC and 1 500 VDC.
It applies to open drive, semi hermetic and hermetic motor compressors, which contain a positive compression function.
This standard is not applicable to:
-   compressors used in household appliance for which EN 60335 2 34 applies;
-   compressors using water or air as refrigerant.
This European Standard does not deal with requirements for vibration and noise.
NOTE 1   Compressors for automotive comfort air conditioning systems can be developed according e.g. SAE J 639.
NOTE 2   Noise emission depends on the complete installation of the built-in compressors and the corresponding operating conditions.
For semi-hermetic and open drive compressors which include moving parts and for which the external envelope is primarily designed for mechanical loads, thermal loads (to limit the possible deformation due to temperature), stiffness of the structure (external mechanical loads and weight of the equipment), taking into account established safe industrial practice, it is considered that pressure is not a significant design factor.
Attached parts covering other functions e.g. oil separators, oil coolers, suction accumulators should comply to EN 14276 1 or EN 13445 6 (cast iron) or EN 13445 8 (aluminium) or showing compliance to the relevant European requirements. This applies also to shells for hermetic compressors either welded or with any kind of permanent joint.
Requirements for compressors used in explosive atmospheres are not covered by this standard.
NOTE 3   For further guidance see EN 13463-1.
This European Standard deals with all significant hazards, hazardous situations and events relevant to compressors, when they are used as intended and under conditions for misuse which are reasonably foreseeable by the manufacturer (see Clause 4).
This European Standard specifies safety requirements for the design, construction, manufacture and testing, documentation and marking of compressors, including integral accessories, e.g. shut-off valve, if necessary.
The requirements in this standard take account of the intended use, as defined in EN ISO 12100:2010, 3.12.
This standard relates to the compressor itself which is to be incorporated in a refrigerating system.
This standard is not applicable to compressors as defined in the scope which are manufactured before the date of publication as EN.

  • Draft
    64 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 4259-5:2024(Main)
Petroleum and related products - Precision of measurement methods and results - Part 5: Statistical assessment of agreement between two different measurement methods that claim to measure the same property (ISO 4259-5:2023)
EN ISO 4259-5:2024

This document covers statistical methodology for assessing the expected agreement between two standard test methods that purport to measure the same property of a material, and deciding if a simple linear bias correction can further improve the expected agreement. It is intended for use with results collected from an interlaboratory study meeting the requirement of ISO 4259-1 or equivalent (for example, ASTM D6300). The interlaboratory study must be conducted on at least ten (10) materials that span the intersecting scopes of the test methods, and results must be obtained from at least six (6) laboratories using each method.
The statistical methodology is based on the premise that a bias correction will not be needed. In the absence of strong statistical evidence that a bias correction would result in better agreement between the two methods, a bias correction is not made. If a bias correction is required, then the parsimony principle is followed whereby a simple correction is to be favoured over a more complex one. Failure to adhere to the parsimony principle generally results in models that are over-fitted and do not perform well in practice.
The bias corrections of this practice are limited to a constant correction, proportional correction or a linear (proportional + constant) correction.
The bias-correction methods of this practice are method symmetric, in the sense that equivalent corrections are obtained regardless of which method is bias-corrected to match the other.
A methodology is presented for establishing the 95 % confidence limit (designated by this practice as the between methods reproducibility) for the difference between two results where each result is obtained by a different operator using different apparatus and each applying one of the two methods X and Y on identical material, where one of the methods has been appropriately bias-corrected in accordance with this practice.
This standard is intended for test methods which measure quantitative (numerical) properties of petroleum or petroleum products.
The statistical methodology outlined in this practice is also applicable for assessing the expected agreement between any two test methods that purport to measure the same property of a material, provided the results are obtained on the same comparison sample set, the standard error associated with each test result is known, and the sample set design meets the requirements of this practice, in particular that the statistical degree of freedom associated with all standard errors are 30 or greater

  • Standard
    56 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    57 pages
    English language
    sale 10% off
    e-Library read for
    1 day