SIST EN 12629-8:2004+A1:2010
(Main)Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 8: Machines and equipment for the manufacture of constructional products from calcium-silicate (and concrete)
Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 8: Machines and equipment for the manufacture of constructional products from calcium-silicate (and concrete)
This part of EN 12629, taken together with EN 12629-1:2000+A1:2010 applies to hydraulic machines for the manufacture of bricks, blocs and elements of calcium-silicate (as illustrated in Annexes A and B). EN 12629-1:2000+A1:2010 specifies general requirements applicable to machines for the manufacture of constructional products from concrete and calcium-silicate. This document specifies the additional requirements to and/or the deviations from EN 12629-1:2000+A1:2010 specific to the machines it covers.This European Standard deals with all significant hazards pertinent to these machines, when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer (see Clause 4). This European Standard specifies the appropriate technical measures to eliminate or reduce risks arising from the significant hazards. Noise hazard and vibration hazard are considered as not significant for those machines. This European Standard applies to the machines from the point at which the mixture enters the machine (see point 1 at annex A, B) until the point where the green products are removed from the machine to the curing system (see point 2 of annex A, B). This document is not applicable to machines and equipment for the manufacture of constructional products from calcium silicate (and concrete), which are manufactured before the date of publication of this document by CEN.
Maschinen für die Herstellung von Bauprodukten aus Beton und Kalksandsteinmassen - Sicherheit - Teil 8: Maschinen zur Herstellung von Bauprodukten aus Kalksandsteinmassen (und Beton)
1.1 Diese Norm gilt für hydraulische Maschinen für die Herstellung von Steinen, Blöcken und Elementen aus Kalksandsteinmassen (wie in den Anhängen A und B beschrieben).
ANMERKUNG Kalksandsteinmasse kann durch Beton ersetzt werden.
1.2 Diese Norm behandelt alle signifikanten Gefährdungen, Gefährdungssituationen und Gefährdungsereignisse, die auf diese Maschinen zutreffen, wenn sie bestimmungsgemäß und entsprechend den vorhersehbaren Bedingungen des Herstellers verwendet werden (siehe Abschnitt 4). Diese Norm spezifiziert die entsprechenden technischen Maßnahmen zur Beseitigung oder Reduzierung der Risiken, die von diesen Gefährdungen ausgehen .
1.3 Der Geltungsbereich dieser Norm beginnt für diese Maschinen bei der Zuführung der Mischung (siehe Punkt 1 in den Anhängen A, B) bis zu der Stelle, wo die Rohlinge abgenommen werden von der Maschine zum Trockenkammersystem (siehe Punkt 2, Anhänge A und B).
1.4 Diese Norm behandelt nicht die Anforderungen zur Verminderung von Gefährdungen durch mechanische, elektrische, pneumatische, hydraulische oder andere Bauteile oder Maschinen, die in den Normen für ihre allgemeine Verwendung (Typ A, B1 und B2-Normen) behandelt sind.
1.5 Diese Norm behandelt die in Abschnitt 4 aufgeführten Gefährdungen, außer Gefährdungen durch Lärm1), die während des Betriebs und der Wartung von Maschinen und Einrichtungen zur Herstellung von Bauprodukten aus Kalksandsteinmassen und Beton einschließlich der Schnittstellen auftreten können, wenn sie entsprechend den Angaben des Herstellers oder seines bevollmächtigten Vertreters betrieben werden.
ANMERKUNG 1 Eine Änderung ist in Vorbereitung, die Lärm behandelt sowie insbesondere Maßnahmen zur Lärmminderung an der Quelle und ein Geräuschmessverfahren einschließlich der Angabe von Geräuschemissionswerten.
ANMERKUNG 2 Schnittstellen zwischen Maschinen zur Herstellung von Bauprodukten aus Kalksandsteinmassen und anderen Maschinen der Anlage werden in EN 12629-1:2000 (Abschnitt 7.2) behandelt.
Diese
Machines pour la fabrication de produits de construction en béton et silico-calcaire - Sécurité - Partie 8: Machines et installations pour la fabrication de produits de construction en silico-calcaire (et en béton)
La présente partie de l'EN 12629, utilisée avec l'EN 12629-1:2000+A1:2010, s'applique aux machines
hydrauliques utilisées pour la fabrication de briques, blocs et éléments en silico-calcaire (telles qu'illustrés dans
les Annexes A et B).
NOTE Le silico-calcaire peut être remplacé par du béton.
L'EN 12629-1:2000+A1:2010 spécifie les prescriptions générales applicables aux machines pour la fabrication
de produits de construction en béton et silico-calcaire.
Le présent document spécifie les prescriptions supplémentaires et/ou les dérogations à l’EN 12629-1:2000+A1:2010
spécifiques aux machines concernées."
1.2 !La présente Norme européenne traite tous les phénomènes dangereux significatifs spécifiques à ces
machines, lorsqu’elles sont utilisées normalement et dans des conditions de mauvais usage que le fabricant
peut raisonnablement prévoir (voir Article 4). Cette Norme européenne spécifie les mesures techniques appropriées
pour éliminer ou réduire les risques dus aux phénomènes dangereux significatifs.
Les risques dus au bruit et aux vibrations sont considérés comme n'étant pas significatifs pour ces machines."
1.3 La présente Norme européenne s’applique aux machines, du point où le mélange pénètre dans la machine
(voir point 1, annexes A et B) jusqu’au point où les produits frais sont transférés de la machine au système
de durcissement (voir point 2, annexes A et B).
!texte supprimé"
1.4 !Le présent document ne s'applique pas aux machines et installations pour la fabrication de produits
de construction en silico-calcaire (et en béton) fabriquées avant la date de publication du présent document
par le CEN."
Stroji za izdelavo gradbenih proizvodov iz betona in apnenega peščenca - Varnost - 8. del: Stroji in oprema za izdelavo gradbenih proizvodov iz apnenega peščenca (in betona)
Ta del EN 12629 skupaj z EN 12629-1:2000+A1:2010 velja za hidravlične stroje za izdelavo opek, blokov in elementov iz apnenega peščenca (kot prikazujeta Dodatka A in B). EN 12629-1:2000+A1:2010 določa splošne zahteve, ki veljajo za stroje za izdelavo gradbenih proizvodov iz betona in apnenega peščenca. Ta dokument določa dodatne zahteve in/ali odstopanja od EN 12629-1:2000+A1:2010, specifične za stroje, ki jih zajema. Ta evropski standard obravnava vse pomembne nevarnosti, ki se nanašajo na te stroje, kadar se uporabljajo kot predvideno in pod pogoji napačne uporabe, ki jih razumno predvidi proizvajalec (glej Klavzulo 4). Ta evropski standard določa primerne tehnične ukrepe za odpravo ali zmanjšanje tveganj, ki se pojavijo zaradi pomembnih nevarnosti. Za te stroje nevarnost hrupa in vibracij ni pomembna. Ta evropski standard velja za stroje od točke, na kateri zmes vstopa v stroj (glej točko 1 Dodatkov A in B), do točke, na kateri gredo zeleni proizvodi iz stroja v sušilni sistem (glej točko 2 Dodatkov A in B). Ta dokument ne velja za stroje in opremo za izdelavo gradbenih proizvodov iz apnenega peščenca (in betona), izdelane pred datumom, ko je CEN objavil ta dokument.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Maschinen für die Herstellung von Bauprodukten aus Beton und Kalksandsteinmassen - Sicherheit - Teil 8: Maschinen zur Herstellung von Bauprodukten aus Kalksandsteinmassen (und Beton)Machines pour la fabrication de produits de construction en béton et silico-calcaire - Sécurité - Partie 8: Machines et installations pour la fabrication de produits de construction en silico-calcaire (et en béton)Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 8: Machines and equipment for the manufacture of constructional products from calcium-silicate (and concrete)91.220Gradbena opremaConstruction equipmentICS:Ta slovenski standard je istoveten z:EN 12629-8:2002+A1:2010SIST EN 12629-8:2004+A1:2010en,fr01-december-2010SIST EN 12629-8:2004+A1:2010SLOVENSKI
STANDARD
SIST EN 12629-8:2004+A1:2010
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 12629-8:2002+A1
September 2010 ICS 91.220 Supersedes EN 12629-8:2002English Version
Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 8: Machines and equipment for the manufacture of constructional products from calcium-silicate (and concrete)
Machines pour la fabrication de produits de construction en béton et silico-calcaire - Sécurité - Partie 8: Machines et installations pour la fabrication de produits de construction en silico-calcaire (et en béton)
Maschinen für die Herstellung von Bauprodukten aus Beton und Kalksandsteinmassen - Sicherheit - Teil 8: Maschinen zur Herstellung von Bauprodukten aus Kalksandsteinmassen (und Beton) This European Standard was approved by CEN on 1 November 2002 and includes Amendment 1 approved by CEN on 5 August 2010.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12629-8:2002+A1:2010: ESIST EN 12629-8:2004+A1:2010
EN 12629-8:2002+A1:2010 (E) 2 Contents page Foreword . 3Introduction . 41Scope . 42Normative references . 53Terms and definitions . 54List of significant hazards . 64.1Mechanical hazards (see informative annexes C and D) . 64.2Electrical hazards . 84.3Hazards caused by the failure of energy supply . 95!!!!Safety requirements and/or protective measures"""" . 96!!!!Verification of safety requirements and/or protective measures"""" . 107Information for use . 108Marking . 11Annex A (informative)
Terminology for a hydraulic press producing bricks blocks and elements . 12Annex B (informative)
Terminology for a hydraulic press without stacking equipment producing elements . 13Annex C (informative)
Hazard zones and requirements for a hydraulic press producing bricks, blocks and elements . 14Annex D (informative)
Hazard zones and requirements for a hydraulic press without stacking equipment producing elements . 15Annex ZA (informative)
!!!! Relationship between this European Standard and the Essential Requirements of EU Directive 2006/42/EC"""" . 16Bibliography . 17
SIST EN 12629-8:2004+A1:2010
EN 12629-8:2002+A1:2010 (E) 3 Foreword This document (EN 12629-8:2002+A1:2010) has been prepared by Technical Committee CEN /TC 151 "Construction equipment and building material machines - Safety", the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by March 2011, and conflicting national standards shall be withdrawn at the latest by March 2011. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document includes Amendment 1, approved by CEN on 2010-08-05. This document supersedes EN 12629-8:2002. The start and finish of text introduced or altered by amendment is indicated in the text by tags ! ". !This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s). For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document." !The series "Machines for the manufacture of constructional products from concrete and calcium – silicate – Safety" consists of following parts: Part 1: Common requirements Part 2: Block making machines Part 3: Slide and turntable machines Part 4: Concrete rooftile making machines Part 5.1: Concrete pipe machines manufacturing in the vertical axis Part 5.2: Concrete pipe machines manufacturing in the horizontal axis Part 5.3: Pipe prestressing machines Part 5.4: Concrete pipe coating machines Part 6: Stationary and mobile equipment for the manufacture of precast reinforced products Part 7: Stationary and mobile equipment for the benched manufacture of prestressed products Part 8: Machines and equipment for the manufacture of constructional products from calcium silicate (and concrete)." !deleted text" According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. SIST EN 12629-8:2004+A1:2010
EN 12629-8:2002+A1:2010 (E) 4 Introduction !This European Standard is a Type C-standard as stated in EN ISO 12100. The machinery concerned and the extent to which hazards, hazardous situation and events are covered are indicated in the scope of this document.
When provisions of this type C document are different from those, which are stated in type A or B documents, the provisions of this type C document take precedence over the provisions of the other documents, for machines that have been designed and built according to the provisions of this type C document.
This document specifies the additional requirements to and/or the deviations from EN 12629-1:2000+A1:2010 specific for the machines and equipment for the manufacture of constructional products from calcium silicate (and concrete) as described in 1.1. With the aim of clarifying the intentions of the document it should be noticed that the following assumptions were made when producing it: specific conditions of use or environmental conditions out of the scope of the document shall be the subject of negotiations between the manufacturer and the user/owner, the equipment will only be used by competent and designated persons,
the place of use/installation is adequately lit,
all operations are carried out by specially trained operators." 1 Scope 1.1 !This part of EN 12629, taken together with EN 12629-1:2000+A1:2010 applies to hydraulic machines for the manufacture of bricks, blocs and elements of calcium-silicate (as illustrated in Annexes A and B). NOTE Calcium-silicate can be replaced by concrete. EN 12629-1:2000+A1:2010 specifies general requirements applicable to machines for the manufacture of constructional products from concrete and calcium–silicate. This document specifies the additional requirements to and/or the deviations from EN 12629-1:2000+A1:2010 specific to the machines it covers." 1.2 !This European Standard deals with all significant hazards pertinent to these machines, when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer (see Clause 4). This European Standard specifies the appropriate technical measures to eliminate or reduce risks arising from the significant hazards. Noise hazard and vibration hazard are considered as not significant for those machines." SIST EN 12629-8:2004+A1:2010
EN 12629-8:2002+A1:2010 (E) 5 1.3 This European Standard applies to the machines from the point at which the mixture enters the machine (see point 1 at annex A, B) until the point where the green products are removed from the machine to the curing system (see point 2 of annex A, B). !deleted text" 1.4 !This document is not applicable to machines and equipment for the manufacture of constructional products from calcium silicate (and concrete), which are manufactured before the date of publication of this document by CEN." 2 Normative references !The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 12629-1:2000+A1:2010, Machines for the manufacture of constructional products from concrete and calcium-silicate — Safety — Part 1: Common requirements. EN ISO 12100-1:2003, Safety of machinery — Basic concepts, general principles for design — Part 1: Basic terminology, methodology (ISO 12100-1:2003) EN ISO 12100-2:2003, Safety of machinery — Basic concepts, general principles for design — Part 2: Technical principles (ISO 12100-2:2003)" 3 Terms and definitions !For the purposes of this document, the terms and definitions given in EN ISO 12100-1:2003,
EN 12629-1:2000+A1:2010 and the following apply." 3.1 table part of the machine in which the mould is set up-down 3.2 transmission levers those parts of the machine that convert rotary motive power into reciprocal movement through gears and cams 3.3 drawing box container having the shape of a box with an open or movable bottom. The drawing box fills the mould with the mixture 3.4 feed hopper
device that contains the mixture which is transported to the drawing box by a discharge gate or a dosing belt 3.5 take off device integral part of the machine, that takes off the formed (green) products and puts them on a green product collection system or arranges them into formation for removal from the machine 3.6 green product collection system
integral transport system which is part of the machine that carries the green product from the take off device to the stacking equipment, or to the point where the green product is removed from the machine SIST EN 12629-8:2004+A1:2010
EN 12629
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.