oSIST prEN 1994-2:2024
(Main)Eurocode 4 - Design of composite steel and concrete structures - Part 2: Bridges
Eurocode 4 - Design of composite steel and concrete structures - Part 2: Bridges
EN 1994-2 gives design rules for steel-concrete composite bridges or members of bridges, supplementary to the general rules given in EN 1994-1-1.
Eurocode 4 - Bemessung und Konstruktion von Verbundtragwerken aus Stahl und Beton - Teil 2: Brücken
Eurocode 4 - Calcul des structures mixtes acier-béton - Partie 2: Ponts
Evrokod 4 - Projektiranje sovprežnih konstrukcij iz jekla in betona - 2. del: Mostovi
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
oSIST prEN 1994-2:2024
01-junij-2024
Evrokod 4 - Projektiranje sovprežnih konstrukcij iz jekla in betona - 2. del: Mostovi
Eurocode 4 - Design of composite steel and concrete structures - Part 2: Bridges
Eurocode 4 - Bemessung und Konstruktion von Verbundtragwerken aus Stahl und Beton
- Teil 2: Brücken
Eurocode 4 - Calcul des structures mixtes acier-béton - Partie 2: Ponts
Ta slovenski standard je istoveten z: prEN 1994-2
ICS:
91.010.30 Tehnični vidiki Technical aspects
91.080.13 Jeklene konstrukcije Steel structures
91.080.40 Betonske konstrukcije Concrete structures
93.040 Gradnja mostov Bridge construction
oSIST prEN 1994-2:2024 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 1994-2:2024
---------------------- Page: 2 ----------------------
oSIST prEN 1994-2:2024
DRAFT
EUROPEAN STANDARD
prEN 1994-2
NORME EUROPÉENNE
EUROPÄISCHE NORM
March 2024
ICS 91.010.30; 91.080.13; 91.080.40; 93.040 Will supersede EN 1994-2:2005
English Version
Eurocode 4 - Design of composite steel and concrete
structures - Part 2: Bridges
Eurocode 4 - Calcul des structures mixtes acier-béton - Eurocode 4 - Bemessung und Konstruktion von
Partie 2: Ponts Verbundtragwerken aus Stahl und Beton - Teil 2:
Brücken
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 250.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 1994-2:2024 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN 1994-2:2024
prEN 1994-2:2024 (E)
Contents
European foreword . 5
0 Introduction . 6
1 Scope . 8
1.1 Scope of EN 1994-2 . 8
1.2 Assumptions . 8
2 Normative references . 8
3 Terms, definitions and symbols . 9
3.1 Terms and definitions . 9
3.2 Symbols and abbreviations . 9
4 Basis of design . 11
4.1 General rules .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.