Protective gloves against dangerous chemicals and micro-organisms - Part 2: Determination of resistance to penetration (ISO 374-2:2019)

This Standard specifies a test method for the penetration resistance of gloves that protect against
dangerous chemicals and/or micro-organisms.

Schutzhandschuhe gegen gefährliche Chemikalien und Mikroorganismen - Teil 2: Bestimmung des Widerstandes gegen Penetration (ISO 374-2:2019)

Dieses Dokument legt ein Prüfverfahren für den Widerstand gegen Penetration von Handschuhen fest, die vor gefährlichen Chemikalien und/oder Mikroorganismen schützen.

Gants de protection contre les produits chimiques dangereux et les micro-organismes - Partie 2: Détermination de la résistance à la pénétration (ISO 374-2:2019)

Le présent document spécifie une méthode d'essai pour la détermination de la résistance à la pénétration des gants de protection contre les produits chimiques et/ou micro-organismes dangereux.

Varovalne rokavice za zaščito pred nevarnimi kemikalijami in mikroorganizmi - 2. del: Ugotavljanje odpornosti proti penetraciji (ISO 374-2:2019)

Ta standard določa preskusno metodo za odpornost proti penetraciji za varovalne rokavice za zaščito pred nevarnimi kemikalijami in mikroorganizmi.

General Information

Status
Published
Public Enquiry End Date
19-Apr-2018
Publication Date
10-Dec-2019
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
27-Nov-2019
Due Date
01-Feb-2020
Completion Date
11-Dec-2019

RELATIONS

Buy Standard

Standard
SIST EN ISO 374-2:2020
English language
16 pages
sale 10% off
Preview
sale 10% off
Preview

e-Library read for
1 day

Standards Content (sample)

SLOVENSKI STANDARD
SIST EN ISO 374-2:2020
01-januar-2020
Nadomešča:
SIST EN 374-2:2015
Varovalne rokavice za zaščito pred nevarnimi kemikalijami in mikroorganizmi - 2.
del: Ugotavljanje odpornosti proti penetraciji (ISO 374-2:2019)
Protective gloves against dangerous chemicals and micro-organisms - Part 2:
Determination of resistance to penetration (ISO 374-2:2019)
Schutzhandschuhe gegen gefährliche Chemikalien und Mikroorganismen - Teil 2:
Bestimmung des Widerstandes gegen Penetration (ISO 374-2:2019)

Gants de protection contre les produits chimiques dangereux et les micro-organismes -

Partie 2: Détermination de la résistance à la pénétration (ISO 374-2:2019)
Ta slovenski standard je istoveten z: EN ISO 374-2:2019
ICS:
13.340.40 Varovanje dlani in rok Hand and arm protection
SIST EN ISO 374-2:2020 en

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO 374-2:2020
---------------------- Page: 2 ----------------------
SIST EN ISO 374-2:2020
EN ISO 374-2
EUROPEAN STANDARD
NORME EUROPÉENNE
October 2019
EUROPÄISCHE NORM
ICS 13.340.40 Supersedes EN 374-2:2014
English Version
Protective gloves against dangerous chemicals and micro-
organisms - Part 2: Determination of resistance to
penetration (ISO 374-2:2019)

Gants de protection contre les produits chimiques Schutzhandschuhe gegen gefährliche Chemikalien und

dangereux et les micro-organismes - Partie 2: Mikroorganismen - Teil 2: Bestimmung des

Détermination de la résistance à la pénétration (ISO Widerstandes gegen Penetration (ISO 374-2:2019)

374-2:2019)
This European Standard was approved by CEN on 29 September 2019.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this

European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references

concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN

member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by

translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management

Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,

Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,

Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and

United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels

© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 374-2:2019 E

worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 374-2:2020
EN ISO 374-2:2019 (E)
Contents Page

European foreword ....................................................................................................................................................... 3

---------------------- Page: 4 ----------------------
SIST EN ISO 374-2:2020
EN ISO 374-2:2019 (E)
European foreword

This document (EN ISO 374-2:2019) has been prepared by Technical Committee ISO/TC 94 "Personal

safety - Personal protective equipment" in collaboration with Technical Committee CEN/TC 162

“Protective clothing including hand and arm protection and lifejackets” the secretariat of which is held

by DIN.

This European Standard shall be given the status of a national standard, either by publication of an

identical text or by endorsement, at the latest by April 2020, and conflicting national standards shall be

withdrawn at the latest by April 2020.

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. CEN shall not be held responsible for identifying any or all such patent rights.

This document supersedes EN 374-2:2014.

According to the CEN-CENELEC Internal Regulations, the national standards organizations of the

following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,

Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,

Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of

North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the

United Kingdom.
Endorsement notice

The text of ISO 374-2:2019 has been approved by CEN as EN ISO 374-2:2019 without any modification.

---------------------- Page: 5 ----------------------
SIST EN ISO 374-2:2020
---------------------- Page: 6 ----------------------
SIST EN ISO 374-2:2020
INTERNATIONAL ISO
STANDARD 374-2
First edition
2019-10
Protective gloves against dangerous
chemicals and micro-organisms —
Part 2:
Determination of resistance to
penetration
Gants de protection contre les produits chimiques dangereux et les
micro-organismes —
Partie 2: Détermination de la résistance à la pénétration
Reference number
ISO 374-2:2019(E)
ISO 2019
---------------------- Page: 7 ----------------------
SIST EN ISO 374-2:2020
ISO 374-2:2019(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2019

All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may

be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting

on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address

below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 374-2:2020
ISO 374-2:2019(E)
Contents Page

Foreword ........................................................................................................................................................................................................................................iv

1 Scope ................................................................................................................................................................................................................................. 1

2 Normative references ...................................................................................................................................................................................... 1

3 Terms and definitions ..................................................................................................................................................................................... 1

4 Test principles ......................................................................................................................................................................................................... 1

4.1 Air leak test ................................................................................................................................................................................................ 1

4.2 Water leak test ......................................................................................................................................................................................... 1

4.3 Remarks ........................................................................................................................................................................................................ 1

5 Sampling ........................................................................................................................................................................................................................ 2

6 Apparatus ..................................................................................................................................................................................................................... 2

6.1 Air leak test ................................................................................................................................................................................................ 2

6.2 Water leak test ......................................................................................................................................................................................... 3

7 Procedure..................................................................................................................................................................................................................... 5

7.1 General ........................................................................................................................................................................................................... 5

7.2 Air leak test ................................................................................................................................................................................................ 5

7.3 Water leak test ......................................................................................................................................................................................... 6

8 Test report ................................................................................................................................................................................................................... 6

Annex A (informative) Informative annex to be used for quality assurance during production...........8

Bibliography ................................................................................................................................................................................................................................ 9

© ISO 2019 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 374-2:2020
ISO 374-2:2019(E)
Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards

bodies (ISO member bodies). The work of preparing International Standards is normally carried out

through ISO technical committees. Each member body interested in a subject for which a technical

committee has been established has the right to be represented on that committee. International

organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.

ISO collabo
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.