SIST EN ISO 9445:2006
(Main)Continuously cold-rolled stainless steel narrow strip, wide strip, plate/sheet and cut lengths - Tolerances on dimensions and form (ISO 9445:2002)
Continuously cold-rolled stainless steel narrow strip, wide strip, plate/sheet and cut lengths - Tolerances on dimensions and form (ISO 9445:2002)
This International Standard specifies the tolerances on dimensions and form for continuously cold-rolled stainless steel narrow strip, in thicknesses of up to and including 3 mm and in rolling widths of less than 600 mm. It also applies to cut lengths taken from such strip. This International Standard also specifies the tolerances on dimensions and form for continuously cold-rolled stainless steel wide strip and plate/sheet, in thicknesses from 0,3 mm to 8,0 mm and in rolling widths from 600 mm to 2 100 mm. It also applies to slit cold-rolled wide strip in widths less than 600 mm manufactured from wide strip by longitudinal slitting and to cut lengths manufactured from such strip.
Kontinuierlich gewalztes Kaltband, Kaltbreitband, Blech und Kaltband in Stäben aus nichtrostenden Stählen - Grenzabmaße und Formtoleranzen (ISO 9445:2002)
1.1 Diese Internationale Norm legt die Grenzabmaße und Formtoleranzen fest für kontinuierlich gewalztes Kaltband aus nichtrostenden Stählen, in Dicken bis einschließlich 3 mm und in Walzbreiten kleiner als
600 mm. Sie gilt auch für Kaltband in Stäben.
1.2 Diese Internationale Norm legt auch die Grenzabmaße und Formtoleranzen fest für kontinuierlich gewalztes Kaltbreitband und Blech aus nichtrostenden Stählen, in Dicken von 0,3 mm bis 8,0 mm und in Walzbreiten von 600 mm bis 2100 mm. Sie gilt auch für längsgeteiltes Kaltbreitband in Breiten unter 600 mm hergestellt aus Kaltbreitband durch Längsteilen und für Stäbe aus diesen Erzeugnissen.
Feuillards, larges bandes, tôles et feuillards coupés a longueur en acier inoxydable laminés a froid en continu - Tolérances sur les dimensions et la forme (ISO 9445:2002)
Kontinuirno hladno valjani ozki trakovi, široki trakovi, pločevine iz nerjavnih jekel in rezane dolžine – Mejni odstopki mer in tolerance oblik (ISO 9445:2002)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 9445:2006
01-maj-2006
1DGRPHãþD
SIST EN 10258:1998
SIST EN 10259:1998
.RQWLQXLUQRKODGQRYDOMDQLR]NLWUDNRYLãLURNLWUDNRYLSORþHYLQHL]QHUMDYQLKMHNHO
LQUH]DQHGROåLQH±0HMQLRGVWRSNLPHULQWROHUDQFHREOLN ,62
Continuously cold-rolled stainless steel narrow strip, wide strip, plate/sheet and cut
lengths - Tolerances on dimensions and form (ISO 9445:2002)
Kontinuierlich gewalztes Kaltband, Kaltbreitband, Blech und Kaltband in Stäben aus
nichtrostenden Stählen - Grenzabmaße und Formtoleranzen (ISO 9445:2002)
Feuillards, larges bandes, tôles et feuillards coupés a longueur en acier inoxydable
laminés a froid en continu - Tolérances sur les dimensions et la forme (ISO 9445:2002)
Ta slovenski standard je istoveten z: EN ISO 9445:2006
ICS:
77.140.20 Visokokakovostna jekla Stainless steels
77.140.50 3ORãþDWLMHNOHQLL]GHONLLQ Flat steel products and semi-
SROL]GHONL products
SIST EN ISO 9445:2006 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 9445:2006
---------------------- Page: 2 ----------------------
SIST EN ISO 9445:2006
EUROPEAN STANDARD EN ISO 9445
NORME EUROPÉENNE
EUROPÄISCHE NORM
March 2006
ICS 77.140.20; 77.140.50 Supersedes EN 10258:1997 and EN 10259:1997
English Version
Continuously cold-rolled stainless steel narrow strip, wide strip,
plate/sheet and cut lengths - Tolerances on dimensions and
form (ISO 9445:2002)
Feuillards, larges bandes, tôles et feuillards coupés à Kontinuierlich gewalztes Kaltband, Kaltbreitband, Blech und
longueur en acier inoxydable laminés à froid en continu - Kaltband in Stäben aus nichtrostenden Stählen -
Tolérances sur les dimensions et la forme (ISO 9445:2002) Tolerances on dimensions and form (ISO 9445:2002)
This European Standard was approved by CEN on 6 February 2006.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,
Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2006 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 9445:2006: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 9445:2006
EN ISO 9445:2006 (E)
Foreword
The text of ISO 9445:2002 has been prepared by Technical Committee ISO/TC 17 "Steel” of
the International Organization for Standardization (ISO) and has been taken over as EN ISO
9445:2006 by Technical Committee ECISS/TC 23 "Steels for heat treatment, alloy steels and
free-cutting steels - Qualities and dimensions", the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication
of an identical text or by endorsement, at the latest by September 2006, and conflicting
national standards shall be withdrawn at the latest by September 2006.
This document supersedes EN 10258:1997 and EN 10259:1997.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary,
Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Endorsement notice
The text of ISO 9445:2002 has been approved by CEN as EN ISO 9445:2006 without any
modifications.
2
---------------------- Page: 4 ----------------------
SIST EN ISO 9445:2006
INTERNATIONAL ISO
STANDARD 9445
Second edition
2002-11-01
Continuously cold-rolled stainless steel
narrow strip, wide strip, plate/sheet and cut
lengths — Tolerances on dimensions and
form
Feuillards, larges bandes, tôles et feuillards coupés à longueur en acier
inoxydable laminés à froid en continu — Tolérances sur les dimensions et
la forme
Reference number
ISO 9445:2002(E)
©
ISO 2002
---------------------- Page: 5 ----------------------
SIST EN ISO 9445:2006
ISO 9445:2002(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not
be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this
file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this
area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2002
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body
in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.ch
Web www.iso.ch
Printed in Switzerland
ii © ISO 2002 – All rights reserved
---------------------- Page: 6 ----------------------
SIST EN ISO 9445:2006
ISO 9445:2002(E)
Contents Page
Foreword . iv
1 Scope. 1
2 Normative reference. 1
3 Terms and definitions. 1
4 Information to be supplied by the purchaser. 1
5 Type of delivery and delivery condition. 2
6 Preferred thicknesses. 3
7 Tolerances on thickness . 3
8 Tolerances on width. 7
9 Preferred coil inner diameters for cold-rolled products . 8
10 Tolerances on length . 8
11 Tolerances on edge camber. 9
12 Tolerances on squareness. 10
13 Tolerances on flatness . 11
14 Edge waviness tolerances for cold-rolled strip . 11
15 Form of coils. 11
16 Ordered format for plate/sheet and cut lengths. 12
17 Measurement of thickness . 12
18 Measurement of width . 12
19 Measurement of length. 12
20 Measurement of edge camber . 12
21 Measurement of squareness. 13
22 Measurement of flatness and waviness. 14
© ISO 2002 – All rights reserved iii
---------------------- Page: 7 ----------------------
SIST EN ISO 9445:2006
ISO 9445:2002(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
The main task of technical committees is to prepare International Standards. Draft International Standards adopted
by the technical committees are circulated to the member bodies for voting. Publication as an International
Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 9445 was prepared by Technical Committee ISO/TC 17, Steel, Subcommittee SC 4, Heat treatable and alloy
steels.
This second edition cancels and replaces the first edition (ISO 9445:1990) as well as ISO 9447:1990, the contents
of which have been combined and technically revised.
iv © ISO 2002 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 9445:2006
INTERNATIONAL STANDARD ISO 9445:2002(E)
Continuously cold-rolled stainless steel narrow strip, wide strip,
plate/sheet and cut lengths — Tolerances on dimensions and form
1 Scope
1.1 This International Standard specifies the tolerances on dimensions and form for continuously cold-rolled
stainless steel narrow strip, in thicknesses of up to and including 3 mm and in rolling widths of less than 600 mm. It
also applies to cut lengths taken from such strip.
1.2 This International Standard also specifies the tolerances on dimensions and form for continuously cold-rolled
stainless steel wide strip and plate/sheet, in thicknesses from 0,3 mm to 8,0 mm and in rolling widths from 600 mm
to 2 100 mm. It also applies to slit cold-rolled wide strip in widths less than 600 mm manufactured from wide strip
by longitudinal slitting and to cut lengths manufactured from such strip.
2 Normative reference
The following normative document contains provisions which, through reference in this text, constitute provisions of
this International Standard. For dated references, subsequent amendments to, or revisions of, any of these
publications do not apply. However, parties to agreements based on this International Standard are encouraged to
investigate the possibility of applying the most recent edition of the normative document indicated below. For
undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC
maintain registers of currently valid International Standards.
ISO 6929:1987, Steel products — Definitions and classification
3 Terms and definitions
For the purposes of this International Standard, the terms and definitions given in ISO 6929 shall apply.
4 Information to be supplied by the purchaser
4.1 It shall be the responsibility of the purchaser to specify all requirements that are necessary for products
under this specification. Such requirements to be considered include, in the order listed, but not limited to, the
following:
a) the type of delivery [see 5.2 a) to f)];
b) the number of this International Standard, i.e. ISO 9445;
c) the thickness, in millimetres, (if necessary accurate to two decimal places) and, if required, including the
relevant code letter (F or P) for a fine or precision tolerance in the case of cold-rolled narrow strip and products
obtained from such strip or including the relevant code letter (S) for a special tolerance in the case of cold-
rolled wide strip and products obtained from such strip;
© ISO 2002 – All rights reserved 1
---------------------- Page: 9 ----------------------
SIST EN ISO 9445:2006
ISO 9445:2002(E)
d) for cold-rolled wide strip and products cut from it, the measurement of thickness method to be used, either
method A in accordance with 17.2.2 and tolerances according to Table 2 with the relevant code letter (A) or
method B in accordance with 17.2.3 and tolerances according to Table 3 with the relevant code letter (B);
e) the width, in millimetres, and if required, including the relevant code letter (F or P) for a fine or precision
tolerance in the case of cold-rolled narrow strip and products obtained from such strip or including the relevant
code letter (S) for a special tolerance in the case of cold-rolled wide strip and products obtained from such
strip;
f) for cold-rolled wide strip and products obtained from such strip, the condition of the edges (M = mill edges,
T = trimmed edges);
g) for plate/sheet and cut lengths, the length, in millimetres, and if a special tolerance is required, the code
letter S;
h) for cold-rolled narrow strip and cut lengths obtained from cold-rolled narrow strip, the code letter R where a
restricted tolerance on edge camber is required;
i) for cold-rolled plate/sheet and cut lengths, the code letter FS where a special tolerance is required for flatness.
EXAMPLE 1 Cold-rolled narrow strip according to this International Standard with a specified thickness of 0,25 mm,
precision thickness tolerance (P), with a specified width of 250 mm, precision tolerance on width (P), and with restricted
tolerance on edge camber (R).
Cold-rolled narrow strip ISO 9445-0,25P ×××× 250P-R
EXAMPLE 2 Cut length obtained from slit cold-rolled wide strip according to this International Standard with a specified
thickness of 1,5 mm, special thickness tolerance (S), measuring method A, with a specified width of 200 mm, special tolerance
on width (S), with a specified length of 500 mm, special tolerance on length (S) and a special tolerance on flatness (FS).
Cut length from slit cold-rolled wide strip ISO 9445-1,5SA ×××× 200S ×××× 500S-FS
4.2 In the absence of information in the order concerning special requirements for tolerances on dimension and
shape [see 4.1 c), e), g), h) and i)], flat products covered by this International Standard shall be delivered according
to the basic specifications of this International Standard, i.e. with normal tolerances.
5 Type of delivery and delivery condition
5.1 General
In the absence of agreements at the time of enquiry and order concerning special requirements for the delivery
conditions given in 5.3 and 5.4, flat products covered by this International Standard will be delivered according to
the basic specifications of this International Standard.
5.2 Type of delivery
Flat products according to this International Standard can be supplied as
a) cold-rolled narrow strip (strip in rolled widths less than 600 mm);
b) cut lengths from cold-rolled narrow strip [cut from cold-rolled narrow strip according to item 5.2 a)];
c) cold-rolled wide strip (strip in rolled widths equal to or greater than 600 mm);
d) cold-rolled plate/sheet [cut from cold-rolled wide strip according to item 5.2 c)];
e) slit, cold-rolled wide strip [manufactured by longitudinal slitting of wide strip according to item 5.2 c)];
f) cut lengths from slit, cold-rolled wide strip [cut from slit, cold-rolled wide strip according to item 5.2 e)].
2 © ISO 2002 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 9445:2006
ISO 9445:2002(E)
5.3 Delivery condition of cold-rolled narrow strip and products obtained from cold-rolled narrow
strip
5.3.1 Cold-rolled narrow strip and cut lengths obtained from cold-rolled narrow strip are usually supplied with cut
edges. These products will have burrs caused by cutting. If there are special requirements for these edges,
corresponding agreements shall be made on ordering. In this case, the strip is deemed to be cut almost free of burr
if the height of the burr is less than 10 % of the product thickness.
5.3.2 By special agreement and depending on the technical equipment of the supplier, cold-rolled narrow strip
and cut lengths obtained from cold-rolled narrow strip can be delivered with special edges, e.g. deburred or
rounded edges.
5.4 Delivery condition of cold-rolled wide strip and products obtained from cold-rolled wide
strip
Cold-rolled wide strip, plate/sheet cut from cold-rolled wide strip, slit cold-rolled wide strip and cut lengths obtained
from slit cold-rolled wide strip are usually supplied with mill or trimmed edges. These products may have burrs.
6 Preferred thicknesses
For cold-rolled wide strip and the products obtained from cold-rolled wide strip [see 5.2 c), d), e) and f)] the
following preferred thicknesses exist:
0,30 mm; 0,40 mm; 0,50 mm; 0,60 mm; 0,70 mm; 0,80 mm; 1,00 mm; 1,20 mm; 1,50 mm; 2,00 mm; 2,50 mm;
3,00 mm; 4,00 mm; 5,00 mm; 6,00 mm.
7 Tolerances on thickness
7.1 Tolerances on thickness for cold-rolled narrow strip and products obtained from cold-rolled
narrow strip
The tolerances on thickness are given in Table 1.
7.2 Tolerances on thickness for cold-rolled wide strip and products obtained from cold-rolled
wide strip
The tolerances on thickness can be taken from Table 2 (see 17.2.2 — method A) or Table 3 (see 17.2.3 —
method B).
NOTE The two tables are necessary for recognizing different “customs and practices” in different countries with respect to
measurement methods.
...
SLOVENSKI OSIST prEN ISO 9445:2004
PREDSTANDARD
september 2004
Kontinuirno hladno valjani ozki trakovi, široki trakovi, pločevine iz nerjavnih
jekel in razrezi - Mejni odstopki mer in tolerance oblik (ISO 9445:2002)
Continuously cold-rolled stainless steel narrow strip, wide strip, plate/sheet and cut
lengths - Tol
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.