SIST EN 10205:2025
(Main)Cold reduced tinmill products - Blackplate
Cold reduced tinmill products - Blackplate
This European Standard specifies requirements for blackplate product in the form of coils intended for direct use and mostly for the production of tinplate, electrolytically chromium / chromium oxide plate (ECCS) and electrolytically zinc coated plate.
Blackplate is specified in nominal thicknesses that are multiples of 0,005 mm from typical 0,10 mm up to 0,60mm.
This European Standard applies to coils in nominal minimum widths of 600 mm.
In addition to this standard the general technical delivery conditions of EN 10021 apply.
NOTE Standard width coils for specific uses, e.g. tab stock, can be slit into narrow strip for supply in coil form.
Kaltgewalzte Verpackungsblecherzeugnisse - Feinstblech
Dieses Dokument legt die Anforderungen an Verpackungsblecherzeugnisse in Form von Band in Coils für die direkte Verwendung und für die häufigste Verwendung zur Erzeugung von elektrolytisch verzinktem Blech oder von Coils, die elektrolytisch entweder mit Zinn (Weißblech) oder Chrom/Chromoxid (ECCS oder ECCS RC) elektrolytisch beschichtet sind.
Feinstblech wird in Nenndicken von typischerweise 0,10 mm bis 0,60 mm in Stufen von 0,005 mm geliefert.
Dieses Dokument gilt für Band in Coils mit einer minimalen Nennbreite von 600 mm.
In Ergänzung zu diesem Dokument gelten die allgemeinen technischen Lieferbedingungen nach EN 10021.
ANMERKUNG Für besondere Anwendungen, z. B. "Laschenband", kann das Band auch als durch Längsteilen hergestelltes schmaleres Band in Coils geliefert werden.
Aciers pour emballage laminés à froid - Fer noir
Le présent document spécifie les exigences relatives aux produits de fer noir sous forme de bobines destinées à un usage direct et principalement à la production de tôles zinguées par électrolyse, ou de bobines revêtues par électrolyse d'étain (fer blanc) ou d'oxyde de chrome/chrome (ECCS ou ECCS-RC).
Le fer noir peut être un produit à simple ou double réduction, il est spécifié en épaisseur nominale multiple de 0,005 mm allant généralement de 0,10 mm jusqu’à 0,60 mm.
Le présent document s'applique aux bobines de largeur nominale minimale égale à 600 mm.
En complément au présent document, les conditions techniques générales de livraison de l’EN 10021 s’appliquent.
NOTE Les bobines de largeur standard pour des usages spécifiques, par exemple stock pour étiquettes de marquage, peuvent être découpée en bande plus étroite pour des livraisons en bobines.
Hladno valjani jekleni izdelki za embalažo - Črna pločevina
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-januar-2025
Hladno valjani jekleni izdelki za embalažo - Črna pločevina
Cold reduced tinmill products - Blackplate
Kaltgewalzte Verpackungsblecherzeugnisse - Feinstblech
Aciers pour emballage laminés à froid - Fer noir
Ta slovenski standard je istoveten z: EN 10205:2024
ICS:
55.040 Materiali in pripomočki za Packaging materials and
pakiranje accessories
77.140.50 Ploščati jekleni izdelki in Flat steel products and semi-
polizdelki products
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN 10205
EUROPEAN STANDARD
NORME EUROPÉENNE
November 2024
EUROPÄISCHE NORM
ICS 77.140.20; 77.140.50 Supersedes EN 10205:2016
English Version
Cold reduced tinmill products - Blackplate
Aciers pour emballage laminés à froid - Fer noir Kaltgewalzte Verpackungsblecherzeugnisse -
Feinstblech
This European Standard was approved by CEN on 23 October 2024.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 10205:2024 E
worldwide for CEN national Members.
Contents Page
European foreword . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Classification and designation . 7
4.1 Classification. 7
4.2 Designation . 8
5 Information to be supplied by the purchaser . 8
5.1 Mandatory information . 8
5.2 Options . 8
5.3 Ordering example . 8
6 Steelmaking process . 9
6.1 General. 9
6.2 Annealing . 9
6.3 Product traceability . 9
6.4 Mill edges/trimmed edges . 9
6.5 Surface characteristics . 9
6.6 Oiling . 10
6.7 Discontinuities . 11
7 Mechanical properties . 11
7.1 General. 11
7.2 Mechanical properties of blackplate . 11
8 Tolerances on dimensions and shape . 13
8.1 Linear dimensions . 13
8.2 Shape . 13
9 Welds within a coil . 14
10 Inspection and Sampling . 14
10.1 Testing procedures and types of documents . 14
10.2 Frequency of testing and sampling. 14
10.3 In case of dispute . 15
11 Test methods . 15
11.1 General. 15
11.2 Tensile test measurement . 16
11.3 Tolerances on dimensions and shape . 21
12 Retests . 24
13 Marking . 24
14 Dispatch and packaging . 24
14.1 Coil dispatch . 24
14.2 Pallet dimensions . 25
Annex A (informative) The Rockwell Hardness test for routine determination . 26
A.1 General . 26
A.2 Test pieces . 26
A.3 Test method . 26
A.4 Hardness for blackplate products . 28
Annex B (informative) List of corresponding former designations . 29
Annex C (informative) The springback test for routine determination of proof strength for
double reduced material. 30
C.1 General . 30
C.2 Principle . 30
C.3 Test pieces . 30
C.4 Test method . 30
Annex D (normative) Tensile testing conditions in case of dispute . 31
D.1 General . 31
D.2 Tensile test piece dimensions . 31
D.3 Elongation measurement. 31
D.4 Testing velocity . 31
Annex E (informative) Indicative tensile strength of blackplate products . 33
Bibliography . 34
European foreword
This document (EN 10205:2024) has been prepared by Technical Committee CEN/TC 459 “ECISS –
European Committee for Iron and Steel Standardization” , the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by May 2025 and conflicting national standards shall be
withdrawn at the latest by May 2025.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 10205:2016.
The main changes compared to the previous edition are listed below:
— the scope and the normative references have been modified;
— the definition “anvil effect” has been deleted;
— Annex A has been removed;
— Annexes C, D and E have been added;
— the Bibliography has been modified.
Any feedback and questions on this document should be directed to the users’ national standards body.
A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Through its sub-committee SC 9 “Coated and uncoated flat products to be used for cold forming” (secretariat:
AFNOR).
1 Scope
This document specifies requirements for blackplate product in the form of coils intended for direct use
and mostly for the production of electrolytically zinc coated plate, or coils electrolytically coated with
either tin (tinplate) or chromium/chromium oxide (ECCS or ECCS-RC).
Blackplate can be a single or double reduced product and is specified in nominal thicknesses that are
multiples of 0,005 mm from typical 0,10 mm up to 0,60 mm.
This document applies to coils in nominal minimum widths of 600 mm.
In addition to this document, the general technical delivery conditions of EN 10021 apply.
NOTE Standard width coils for specific uses, e.g. tab stock, can be slit into narrow strip for supply in coil form.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dat
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.