SIST EN IEC 60684-3-247:2019
(Main)Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 247: Heat-shrinkable, polyolefin sleeving, dual wall, not flame retarded, thick and medium wall (IEC 60684-3-247:2019)
Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 247: Heat-shrinkable, polyolefin sleeving, dual wall, not flame retarded, thick and medium wall (IEC 60684-3-247:2019)
This document gives the requirements for two types of heat-shrinkable, polyolefin sleeving, dual wall, not flame retarded with a nominal shrink ratio of 3:1. This sleeving has been found suitable for use at temperatures of up to 100 °C. • Type A: Medium wall, internal diameter up to 200,0 mm typically. • Type B: Thick wall, internal diameter up to 200,0 mm typically. These sleevings are normally supplied in colour black. Since these types of sleving cover a significantly large range of sizes and wall thicknesses, Annex A (Tables A.1 and A.2) provides a guide to the range of sizes available. The actual size will be agreed between the user and supplier. Materials which conform to this specification meet established levels of performance. However, the selection of a material by a user for a specific application will be based on the actual requirements necessary for adequate performance in that application and not based on this specification alone.
Isolierschläuche - Teil 3: Anforderungen für einzelne Schlauchtypen - Blatt 247: Wärmeschrumpfende Polyolefinschläuche mit Innenbeschichtung, nicht flammhemmend, dickwandig und mittlere Wanddicke (IEC 60684-3-247:2019)
Gaines isolantes souples - Partie 3: Spécifications pour types particuliers de gaines - Feuille 247: Gaines thermorétractables en polyoléfine, à double paroi (épaisse et moyenne), non retardées à la flamme (IEC 60684-3-247:2019)
IEC 60684-3-247:2019 est disponible sous forme de IEC 60684-3-247:2019 RLV qui contient la Norme internationale et sa version Redline, illustrant les modifications du contenu technique depuis l'édition précédente.
L'IEC 60684-3-247:2019 donne les exigences relatives à deux types de gaines thermorétractables en polyoléfine, à double paroi, non ignifugées, dont le rapport de rétreint nominal est 3:1. Ces gaines se sont avérées appropriées pour une utilisation à des températures allant jusqu’à 100 °C.
- Type A: Paroi moyenne, diamètre intérieur généralement jusqu’à 200 mm
- Type B: Paroi épaisse, diamètre intérieur généralement jusqu’à 200 mm
La couleur de ces gaines est normalement le noir. Comme ces types de gaines couvrent une plage très étendue de tailles et d’épaisseurs de paroi, l'Annexe A (Tableaux A.1 et A.2) fournit un guide des tailles disponibles dans cette plage. La taille réelle fait l’objet d’un accord entre l’utilisateur et le fournisseur.Anchor Les matériaux conformes à la présente spécification satisfont à des niveaux de performances établis. Cependant, le choix d’un matériau par un utilisateur, pour une application spécifique, est fondé sur les exigences réelles nécessaires pour obtenir des performances adéquates pour l'application concernée, et n'est pas fondé sur cette seule spécification. Cette deuxième édition annule et remplace la première édition parue en 2011 et l'Amendement 1:2016. Cette édition constitue une révision technique.
Cette édition inclut les modifications techniques majeures suivantes par rapport à l'édition précédente:
- suppression de l'essai de solidité de la couleur à la lumière, cet essai étant couvert par l'essai de détermination de la teneur en noir de carbone;
- modification de la température de l'essai de flexion à basse température qui devient -20 °C pour aligner la valeur avec celle donnée dans la feuille 214;
- modification de la température de conditionnement finale des échantillons pour la résistance à l'arrachement qui devient 200 ºC pour aligner la valeur avec celle donnée à l'Article 5;
- suppression de l'essai de résistance aux moisissures étant donné qu'il n'a pas été démontré, ni par des essais, ni en fonctionnement, que le développement de moisissures constituait un problème.
Mots-clés: Gaines thermorétractables en polyoléfine, à double paroi, non ignifugées, à paroi épaisse et moyenne
Gibke izolacijske cevi - 3. del: Specifikacije za posamezne tipe cevi - 247. list: Toplotno skrčljive poliolefinske cevi z dvojno steno, neognjevarne, debelostenske in srednje debele stene (IEC 60684-3-247:2019)
Ta dokument podaja zahteve za dva tipa toplotno skrčljivih poliolefinskih cevi z dvojno steno, neognjevarne, z nazivnimi razmerji krčenja do 3:1. Te cevi so primerne za uporabo pri temperaturi do 100 °C.
• Tip A: srednje debela stena, notranji premer običajno do 200,0 mm. • Tip B: debela stena, notranji premer običajno do 200,0 mm. Te cevi so običajno dobavljive v črni barvi. Ker ta tipa cevi zajemata bistveno velik razpon velikosti in debelin sten, so v tabelah A.1 in A.2 v dodatku A podana navodila glede razpona razpoložljivih velikosti. O dejanski velikosti se dogovorita uporabnik in dobavitelj. Materiali, ki so skladni s to specifikacijo, ustrezajo določenim ravnem delovanja. Vendar uporabnik bo material za določeno uporabo izbral glede na dejanske zahteve, ki omogočajo ustrezno delovanje pri tej uporabi, in ne samo na podlagi te specifikacije.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN IEC 60684-3-247:2019
01-december-2019
Nadomešča:
SIST EN 60684-3-247:2011
SIST EN 60684-3-247:2011/A1:2017
Gibke izolacijske cevi - 3. del: Specifikacije za posamezne tipe cevi - 247. list:
Toplotno skrčljive poliolefinske cevi z dvojno steno, neognjevarne, debelostenske
in srednje debele stene (IEC 60684-3-247:2019)
Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet
247: Heat-shrinkable, polyolefin sleeving, dual wall, not flame retarded, thick and
medium wall (IEC 60684-3-247:2019)
Isolierschläuche - Teil 3: Anforderungen für einzelne Schlauchtypen - Blatt 247:
Wärmeschrumpfende Polyolefinschläuche mit Innenbeschichtung, nicht flammhemmend,
dickwandig und mittlere Wanddicke (IEC 60684-3-247:2019)
Gaines isolantes souples - Partie 3: Spécifications pour types particuliers de gaines -
Feuille 247: Gaines thermorétractables en polyoléfine, à double paroi (épaisse et
moyenne), non retardées à la flamme (IEC 60684-3-247:2019)
Ta slovenski standard je istoveten z: EN IEC 60684-3-247:2019
ICS:
29.035.20 Plastični in gumeni izolacijski Plastics and rubber insulating
materiali materials
SIST EN IEC 60684-3-247:2019 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN IEC 60684-3-247:2019
---------------------- Page: 2 ----------------------
SIST EN IEC 60684-3-247:2019
EUROPEAN STANDARD EN IEC 60684-3-247
NORME EUROPÉENNE
EUROPÄISCHE NORM
October 2019
ICS 29.035.20 Supersedes EN 60684-3-247:2011 and all of its
amendments and corrigenda (if any)
English Version
Flexible insulating sleeving - Part 3: Specifications for individual
types of sleeving - Sheet 247: Heat-shrinkable, polyolefin
sleeving, dual wall, not flame retarded, thick and medium wall
(IEC 60684-3-247:2019)
Gaines isolantes souples - Partie 3: Spécifications pour Isolierschläuche - Teil 3: Anforderungen für einzelne
types particuliers de gaines - Feuille 247: Gaines Schlauchtypen - Blatt 247: Wärmeschrumpfende
thermorétractables en polyoléfine, à double paroi, non Polyolefinschläuche mit Innenbeschichtung, nicht
ignifugées à paroi épaisse et moyenne flammhemmend, dickwandig und mittlere Wanddicke
(IEC 60684-3-247:2019) (IEC 60684-3-247:2019)
This European Standard was approved by CENELEC on 2019-09-12. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 60684-3-247:2019 E
---------------------- Page: 3 ----------------------
SIST EN IEC 60684-3-247:2019
EN IEC 60684-3-247:2019 (E)
European foreword
The text of document 15/890/FDIS, future edition 2 of IEC 60684-3-247, prepared by IEC/TC 15 "Solid
electrical insulating materials" was submitted to the IEC-CENELEC parallel vote and approved by
CENELEC as EN IEC 60684-3-247:2019.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2020-06-12
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2022-09-12
document have to be withdrawn
This document supersedes EN 60684-3-247:2011 and all of its amendments and corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Endorsement notice
The text of the International Standard IEC 60684-3-247:2019 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following note has to be added for the standard indicated:
IEC 60684-3 (series) NOTE Harmonized as EN 60684-3-420 to 422 (series)
2
---------------------- Page: 4 ----------------------
SIST EN IEC 60684-3-247:2019
EN IEC 60684-3-247:2019 (E)
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 60296 2012 Fluids for electrotechnical applications - Unused EN 60296 2012
mineral insulating oils for transformers and
switchgear
IEC 60684-1 2003 Flexible insulating sleeving - Part 1: Definitions and EN 60684-1 2003
general requirements
IEC 60684-2 2011 Flexible insulating sleeving - Part 2: Methods of test EN 60684-2 2011
IEC 60757 1983 Code for designation of colours HD 457 S1 1985
ISO 868 2003 Plastics and ebonite - Determination of indentation EN ISO 868 2003
hardness by means of a durometer (Shore
hardness)
ISO 11357-3 2018 Plastics - Differential scanning calorimetry (DSC) - EN ISO 11357-3 2018
Part 3: Determination of temperature and enthalpy
of melting and crystallization
ISO 11358-1 - Plastics - Thermogravimetry (TG) of polymers - EN ISO 11358-1 2014
Part 1: General principles
3
---------------------- Page: 5 ----------------------
SIST EN IEC 60684-3-247:2019
---------------------- Page: 6 ----------------------
SIST EN IEC 60684-3-247:2019
IEC 60684-3-247
®
Edition 2.0 2019-08
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Flexible insulating sleeving –
Part 3: Specifications for individual types of sleeving –
Sheet 247: Heat-shrinkable, polyolefin sleeving, dual wall, not flame retarded,
thick and medium wall
Gaines isolantes souples –
Partie 3: Spécifications pour types particuliers de gaines –
Feuille 247: Gaines thermorétractables en polyoléfine, à double paroi, non
ignifugées à paroi épaisse et moyenne
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 29.035.20 ISBN 978-2-8322-7213-8
Warning! Make sure that you obtained this publication from an authorized distributor.
Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.
® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale
---------------------- Page: 7 ----------------------
SIST EN IEC 60684-3-247:2019
– 2 – IEC 60684-3-247:2019 © IEC 2019
CONTENTS
FOREWORD . 3
INTRODUCTION . 5
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 7
4 Designation . 7
5 Conditions of test . 7
6 Requirements . 7
7 Sleeving conformance . 7
Annex A (informative) Guide to the available sizes and wall thicknesses . 12
Bibliography . 14
Table 1 – Property requirements . 8
Table 2 – Requirements for breakdown voltage . 11
Table 3 – Resistance to selected fluids . 11
Table A.1 – Type A medium wall . 12
Table A.2 – Type B thick wall . 13
---------------------- Page: 8 ----------------------
SIST EN IEC 60684-3-247:2019
IEC 60684-3-247:2019 © IEC 2019 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
FLEXIBLE INSULATING SLEEVING –
Part 3: Specifications for individual types of sleeving –
Sheet 247: Heat-shrinkable, polyolefin sleeving, dual wall,
not flame retarded, thick and medium wall
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60684-3-247 has been prepared by IEC technical committee 15:
Solid electrical insulating materials.
This second edition cancels and replaces the first edition published in 2011 and
A
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.