iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN 1092-2:1998

(Main)

Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories, PN designated - Part 2: Cast iron flanges

Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories, PN designated - Part 2: Cast iron flanges

This part of EN 1092 specifies requirements for circular flanges made from ductile, grey and malleable cast iron for DN 10 to DN 4000 and PN 63. (See 4.1 and 4.2). This standard specifies the types of flanges and their facings, dimension and tolerances, bolt sizes, surface finish of jointing faces, marking testing, quality assurance and materials together with associated pressure/ temperature (p/T) ratings.

Flansche und ihre Verbindungen - Runde Flansche für Rohre, Armaturen, Formstücke und Zubehörteile, nach PN bezeichnet - Teil 2: Gußeisenflansche

Diese Norm legt die Anforderungen an runde Flansche aus Gusseisen mit Kugel- graphit, Gusseisen mit Lamellengraphit und aus Temperguss von DN10 bis DN 4000 und PN 2,5 bis PN 63 (siehe 4.1 und 4.2) fest. Diese Norm legt die Flanschtypen und ihre Dichtflächen, Masse, Toleranzen, Schraubengrössen, Oberflächenbe- schaffenheit der Dichtflächen, Kennzeichnung, Prüfung, Qualitätssicherung undWerkstoffe zusammen mit den zugehörigen Druck/Temperatur-Zuordnungen fest.

Brides et leurs assemblages - Brides circulaires pour tuyaux, appareil de robinetterie, raccords et accessoires, désignées PN - Partie 2: Brides en fonte

La présente norme spécifie les exigences pour les brides circulaires en fonte ductile, grise et malléable pour DN 10 a DN 4000 et PN 2,5 a PN 63 (voir 4.1 et 4.2). La présente norme spécifie les types de brides et leurs portées de joints,les dimensions de boulonnerie, les dimensions et tolérances, les états de sur- face des portées de joints, le marquage, les essais, l'assurance qualité ainsi qualité ainsi que les matériaux et leurs relations pression/température (p/T) associées a ces brides.

Prirobnice in prirobnični spoji - Okrogle prirobnice za cevi, ventile, vezne elemente (fitinge) in dodatke z oznako PN - 2. del: Prirobnice iz litega železa

General Information

Status
Withdrawn
Publication Date
30-Sep-1998
Withdrawal Date
11-Jan-2024
ICS
23.040.60 - Flanges, couplings and joints
Technical Committee
TLP - Pressure vessels
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
15-Dec-2023
Due Date
07-Jan-2024
Completion Date
12-Jan-2024
Directive
89/106/EEC - Construction products
90/531/EEC - Procurement procedures of entities operating in the water, energy, transport and telecommunications sectors
93/38/EEC - Procurement procedures of entities operating in the water, energy, transport and telecommunications sectors
Mandate
M/109 - Mandate to CEN/CENELEC concerning the execution of standardization work for harmonized standards on fire alarm/detection, fixed firefighting, fire and smoke control and explosion suppression products
Ref Project
EN 1092-2:1997 - Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories, PN designated - Part 2: Cast iron flanges

Relations

Replaced By
SIST EN 1092-2:2024 - Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories, PN designated - Part 2: Cast iron flanges
Effective Date
01-Feb-2024

Buy Standard

EN 1092-2:1998EN 1092-2:1998
PreviousNext
Standard
EN 1092-2:1998
English language
46 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.HOH]DFlansche und ihre Verbindungen - Runde Flansche für Rohre, Armaturen, Formstücke und Zubehörteile, nach PN bezeichnet - Teil 2: GußeisenflanscheBrides et leurs assemblages - Brides circulaires pour tuyaux, appareil de robinetterie, raccords et accessoires, désignées PN - Partie 2: Brides en fonteFlanges and their joints - Circular flanges for pipes, valves, fittings and accessories, PN designated - Part 2: Cast iron flanges23.040.60Prirobnice, oglavki in spojni elementiFlanges, couplings and jointsICS:Ta slovenski standard je istoveten z:EN 1092-2:1997SIST EN 1092-2:1998en01-oktober-1998SIST EN 1092-2:1998SLOVENSKI
STANDARD



SIST EN 1092-2:1998



SIST EN 1092-2:1998



SIST EN 1092-2:1998



SIST EN 1092-2:1998



SIST EN 1092-2:1998



SIST EN 1092-2:1998



SIST EN 1092-2:1998



SIS
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN 1092-2:2024(Main)
Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories, PN designated - Part 2: Cast iron flanges
EN 1092-2:2023

This standard specifies requirements for circular flanges made from ductile, grey and malleable cast iron for DN 10 to DN 4000 and PN 2,5 to PN 100 (See 4.1 and 4.2 for information regarding allowed DN, PN and DN-PN combination).
This standard specifies the types of flanges and their facings, dimension and tolerances, bolt sizes, surface finish of jointing faces, marking, testing, quality assurance and materials together with associated pressure/temperature (p/T) ratings.

  • Standard
    61 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    61 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1515-4:2021/AC:2022(Corrigendum)
Flanges and their joints - Bolting - Part 4: Selection of bolting for equipment subject to the Pressure Equipment Directive 2014/68/EU
EN 1515-4:2021/AC:2022

This document is applicable to the selection of bolting for flanged joints on equipment subject to the Pressure Equipment Directive 2014/68/EU.
It specifies standards and additional requirements for dimensions, material properties and technical conditions of delivery for bolting.
NOTE 1   Washers are not within the scope of this document.
The selection is based on commonly used bolting. It covers common temperature ranges of the general service of flanges.
When selecting bolting according to this document it is essential to take into account environmental conditions and other parameters including type of fluids, corrosion hazards, sour service, low temperature brittle failure and relaxation at elevated temperatures.
The purpose of this document is to provide a selection of most commonly used bolting types and bolting material combinations.
It is not the intention to specify all possible applications but to give guidance on the most common applications. For example, application limits for material in the creep range are not explicitly covered in this document. Where material standard provides mechanical properties for the creep range respective reference is made in Table 3.
NOTE 2   Special services and ambient conditions may require the application of coatings. It is the purchaser’s option to decide on this. Depending on the coating used, a verification of the temperature ranges given in Table 3 and Table 4 may be required.
NOTE 3   In Annex B there are bolting types and bolting material combinations according to commonly used national standards other than those listed in Table 2, Table 3 and Table 4.

  • Corrigendum
    2 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 14525:2022(Main)
Ductile iron and steel wide tolerance couplings and flange adaptors for use with pipes of different materials: ductile iron, Grey iron, steel, PVC-U, PVC-O, PE, fibre-cement
EN 14525:2022

This document specifies the requirements and associated test methods applicable to wide tolerance ductile iron and steel couplings, stepped/reducing couplings and flange adaptors intended for use with pipe components made from a number of pipe materials (ductile iron, grey iron, PE in conformity with EN 12201-1 to EN 12201-5, PVC-U in conformity with EN ISO 1452-1 to EN ISO 1452-5, steel, fibre-cement), for providing a leak tight seal over a wide range of pipe outside diameters:
-   to convey water (e.g. water intended for human consumption );
-   with or without pressure;
-   to be installed below or above ground, inside or outside buildings.
This document is not intended to cover sewerage or gas applications, where additional requirements may be necessary.
This document specifies requirements for materials, dimensions and tolerances, mechanical properties and standard coatings of products.
This document covers wide tolerance couplings, stepped/reducing couplings and flange adaptors:
-   Manufactured with socketed or flanged ends;
-   Supplied externally and internally coated;
-   Suitable for ductile iron in conformity with EN 545, grey iron, PE in conformity with EN 12201-1 to EN 12201-5, PVC-U in conformity with EN ISO 1452-1 to EN ISO 1452-5, steel, fibre-cement in a size range extending from DN 40 to DN 700, for an allowable operating pressure (PFA) up to 16 bar, for fluid temperatures between 0 °C and 25 °C excluding frost. For higher temperatures, (up to 45 °C for PVC-U or 40 °C for PE) the PFA is derated as given in EN ISO 1452 and EN 12201;
-   Not intended for use in areas subjected to reaction to fire regulations.
NOTE 1   This does not preclude special arrangements for the products to be used at higher temperatures. Temperature limitations and pressure limitations are those coming from the PVC-U or PE pipes.
This document covers ductile iron couplings, stepped/reducing couplings and flange adaptors cast by any type of foundry process or manufactured by fabrication of cast components, as well as corresponding joints, in a size range extending from DN 40 to DN 700, to be used with pipes of external diameter from 40 mm to 710 mm.
As long as no equivalent European Standard exists for steel accessories, this document also covers couplings and flange adaptors which are fabricated partly or entirely from steel as well as corresponding joints, in a size range extending from DN 60 to DN 700, to be used with pipes of external diameter from 63 mm to 710 mm.
This document specifies requirements for materials, dimensions and tolerances, mechanical properties and standard coatings. It also gives minimum performance requirements for all components, including restrained and non-restrained flexible joints. Joint design and gasket shapes are outside the scope of this document.
NOTE 2   PFA can be limited depending on pipe materials effectively connected.
NOTE 3   In this document, if not specified, all pressures are relative gauge pressures, expressed in bars (100 kPa = 1 bar).

  • Standard
    34 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    32 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1515-4:2021(Main)
Flanges and their joints - Bolting - Part 4: Selection of bolting for equipment subject to the Pressure Equipment Directive 2014/68/EU
EN 1515-4:2021

This European Standard is applicable to the selection of bolting for equipment subject to the Pressure Equipment Directive 2014/68/EU.
It specifies standards and additional requirements for dimensions, materials and technical conditions of delivery for bolting.
The bolting selection covered by this European Standard is regarded to be used for combination with flanges according to the series EN 1092 (PN designated flanges) and the series EN 1759 (Class designated flanges).
The selection is based on commonly used materials, bolts and nuts. It covers temperature ranges of the general service of standard flanges (based on PN or Class).
NOTE 1   The bolting selection given may be used in combination with non-standard flanges too provided that the range of application of the equipment for which the bolting is intended to be used is covered. It is the purchaser's option to decide on this.
When selecting bolting according to this European Standard it is essential to take into account other parameters such as type of fluids, corrosion hazards and relaxation at elevated temperatures.
The purpose of this European Standard is to provide a selection of most commonly used bolting types and bolting material combinations as well a tool for easy selection of suitable bolting for equipment.
It is not the intention to specify all possible applications but to give guidance on the most commonly applications. According to this, e.g. application limits for material in the creep range are not explicitly covered in this European Standard but some bolting materials listed (see Table 3, footnote h) are suitable to be used in this temperature range. Wherever the starting material standard provides mechanical properties for this temperature range respective reference is made in Table 3.
NOTE 2   Special services and ambient conditions may require the application of coatings. It is the purchaser's option to decide on this. Depending on the coating used, a verification of the temperature ranges

  • Standard
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 14772:2021(Main)
Flanges and their joints - Quality assurance inspection and testing of gaskets in accordance with the series of standards EN 1514 and EN 12560
EN 14772:2021

This document specifies the quality assurance procedures that are applicable to ensure that delivered gaskets comply with the relevant product standards. This document sets down procedures by which a user can have confidence that the salient features of each batch of gaskets or gasket materials delivered to him will be constant.
The gasket types covered by this document are those that are within the scope of the series of standards
EN 1514 and EN 12560 and are simultaneously within the scope of the series of standards EN 1591. An exception is those gaskets intended solely for domestic fluids (like water, waste water ...) which are based on rubber with or without reinforcement like fillers and/or inserts.

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1514-2:2014+A1:2021(Main)
Flanges and their joints - Gaskets for PN-designated flanges - Part 2: Spiral wound gaskets for use with steel flanges
EN 1514-2:2014+A1:2021

This part of EN 1514 specifies the dimensions and marking of spiral wound gaskets for use in conjunction with flat face and raised face flanges complying with the requirements of EN 1092-1 for PN 10, PN 16, PN 25, PN 40, PN 63, PN 100 and PN 160 and up to and including DN 1 000.
NOTE 1   Dimensions of other types of gaskets for use with flanges to EN 1092-1, EN 1092-2, EN 1092-3 and EN 1092 4 are given in EN 1514-1, EN 1514-3, EN 1514-4, EN 1514-6, EN 1514-7 and EN 1514-8.
NOTE 2   Annex A lists information to be supplied by the purchaser when ordering gaskets in circumstances where the choice of the gasket materials appropriate to the service is left to the manufacturer.

  • Standard
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 13555:2021(Main)
Flanges and their joints - Gasket parameters and test procedures relevant to the design rules for gasketed circular flange connections
EN 13555:2021

This European Standard specifies the gasket parameters required by EN 1591 1 and provides the test procedures for establishing the values of these parameters.
Gaskets which are wholly based upon elastomers, or based upon elastomers with only the inclusion of particulate fillers or particulate reinforcement, as opposed to gaskets combining elastomers, fillers and fibrous reinforcement, are beyond the scope of this document.
NOTE   The testing procedures given might be applicable to gaskets of other shapes and dimensions.

  • Standard
    40 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    40 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST-TP CEN/TR 1591-2:2020(Main)
Flanges and their joints - Design rules for gasketed circular flange connections - Part 2: Gasket parameters
CEN/TR 1591-2:2020

This document details generic gasket parameters for use in EN 1591-
1 during preliminary calculations during which the type of gasket to be
used in an application is to be decided. Once the gasket type has
been decided the parameters for gaskets of that type from the
different potential commercial suppliers should be used in further
calculations as within a gasket type there will be differences
depending upon the supplier.

  • Technical report
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    40 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1092-1:2018(Main)
Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories, PN designated - Part 1: Steel flanges
EN 1092-1:2018

This draft European Standard for a single series of flanges specifies requirements for circular steel flanges in PN designations PN 2,5 to PN 400 and nominal sizes from DN 10 to DN 4000.
This draft European Standard specifies the flange types and their facings, dimensions, tolerances, threading, bolt sizes, flange jointing face surface finish, marking, materials, pressure/ temperature ratings and approximate flange masses.
For the purpose of this draft European Standard, "flanges" include also lapped ends and collars.
This draft European Standard applies to flanges manufactured in accordance with the methods described in Table 1.
Non-gasketed pipe joints are outside the scope of this draft European Standard.

  • Standard
    148 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    150 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1591-1:2014(Main)
Flanges and their joints - Design rules for gasketed circular flange connections - Part 1: Calculation
EN 1591-1:2013

This European Standard defines a calculation method for bolted, gasketed, circular flange joints. Its purpose is to ensure structural integrity and control of leak tightness. It uses gasket parameters based on definitions and test methods specified in EN 13555. The calculation method is not applicable to joints with a metallic contact out of the sealing face or to joints whose rigidity varies appreciably across gasket width. For gaskets in incompressible materials, which permit large deformations, the results given by the calculation method can be excessively conservative (i.e. required bolting load too high, allowable pressure of the fluid too low, required flange thickness too large, etc.).

  • Standard
    76 pages
    English language
    sale 10% off
    e-Library read for
    1 day