SIST EN ISO 15626:2013
(Main)Non-destructive testing of welds - Time-of-flight diffraction technique (TOFD) - Acceptance levels (ISO 15626:2011)
Non-destructive testing of welds - Time-of-flight diffraction technique (TOFD) - Acceptance levels (ISO 15626:2011)
This International Standard specifies acceptance levels for the time-of-flight diffraction technique (TOFD) of These acceptance levels are applicable to indications classified in accordance with ISO 10863.
Zerstörungsfreie Prüfung von Schweißverbindungen - Beugungslaufzeittechnik (TOFD) - Zulässigkeitsgrenzen (ISO 15626:2011)
Diese Internationale Norm legt die Zulässigkeitsgrenzen fest für die Prüfung von durchgeschweißten Verbindungen von ferritischen Stählen zwischen 6 mm und 300 mm mittels Beugungslaufzeittechnik (TOFD), die den Qualitätsanforderungen in ISO 5817 entsprechen.
Diese Zulässigkeitsgrenzen sind anwendbar auf Anzeigen, die nach ISO 10863 eingestuft wurden.
Contrôle non destructif des assemblages soudés - Technique de diffraction des temps de vol (TOFD) - Niveaux d'acceptation (ISO 15626:2011)
L'ISO 15626:2011 spécifie les niveaux d'acceptation pour la technique de diffraction des temps de vol (méthode TOFD) utilisée sur des joints soudés à pleine pénétration pratiqués sur des aciers ferritiques d'épaisseur comprise entre 6 mm et 300 mm, correspondant aux niveaux de qualité énoncés dans l'ISO 5817.
Ces niveaux d'acceptation sont applicables à des indications classifiées conformément à l'ISO 10863.
Neporušitveno preskušanje zvarnih spojev - Metoda ultrazvočne difrakcije za odkrivanje in ugotavljanje velikosti nepopolnosti (TOFD) - Stopnje sprejemljivosti (ISO 15626:2011)
Ta mednarodni standard določa stopnje sprejemljivosti za metodo ultrazvočne difrakcije za odkrivanje in ugotavljanje velikosti nepopolnosti (TOFD). Te stopnje sprejemljivosti se uporabljajo za oznake, razvrščene v skladu s standardom ISO 10863.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 15626:2013
01-december-2013
1DGRPHãþD
SIST EN 15617:2009
1HSRUXãLWYHQRSUHVNXãDQMH]YDUQLKVSRMHY0HWRGDXOWUD]YRþQHGLIUDNFLMH]D
RGNULYDQMHLQXJRWDYOMDQMHYHOLNRVWLQHSRSROQRVWL 72)' 6WRSQMHVSUHMHPOMLYRVWL
,62
Non-destructive testing of welds - Time-of-flight diffraction technique (TOFD) -
Acceptance levels (ISO 15626:2011)
Zerstörungsfreie Prüfung von Schweißverbindungen - Beugungslaufzeittechnik (TOFD) -
Zulässigkeitsgrenzen (ISO 15626:2011)
Contrôle non destructif des assemblages soudés - Technique de diffraction des temps
de vol (TOFD) - Niveaux d'acceptation (ISO 15626:2011)
Ta slovenski standard je istoveten z: EN ISO 15626:2013
ICS:
25.160.40 Varjeni spoji in vari Welded joints
SIST EN ISO 15626:2013 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 15626:2013
---------------------- Page: 2 ----------------------
SIST EN ISO 15626:2013
EUROPEAN STANDARD
EN ISO 15626
NORME EUROPÉENNE
EUROPÄISCHE NORM
August 2013
ICS 25.160.40 Supersedes EN 15617:2009
English Version
Non-destructive testing of welds - Time-of-flight diffraction
technique (TOFD) - Acceptance levels (ISO 15626:2011)
Contrôle non destructif des assemblages soudés - Zerstörungsfreie Prüfung von Schweißverbindungen -
Technique de diffraction des temps de vol (TOFD) - Beugungslaufzeittechnik (TOFD) - Zulässigkeitsgrenzen
Niveaux d'acceptation (ISO 15626:2011) (ISO 15626:2011)
This European Standard was approved by CEN on 8 August 2013.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2013 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 15626:2013: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 15626:2013
EN ISO 15626:2013 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 15626:2013
EN ISO 15626:2013 (E)
Foreword
The text of ISO 15626:2011 has been prepared by Technical Committee ISO/TC 44 “Welding and allied
processes” of the International Organization for Standardization (ISO) and has been taken over as EN ISO
15626:2013 by Technical Committee CEN/TC 121 “Welding” the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by February 2014, and conflicting national standards shall be withdrawn
at the latest by February 2014.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 15617:2009.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 15626:2011 has been approved by CEN as EN ISO 15626:2013 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 15626:2013
---------------------- Page: 6 ----------------------
SIST EN ISO 15626:2013
INTERNATIONAL ISO
STANDARD 15626
First edition
2011-02-01
Non-destructive testing of welds — Time-
of-flight diffraction technique (TOFD) —
Acceptance levels
Contrôle non destructif des assemblages soudés — Technique de
diffraction des temps de vol (TOFD) — Niveaux d'acceptation
Reference number
ISO 15626:2011(E)
©
ISO 2011
---------------------- Page: 7 ----------------------
SIST EN ISO 15626:2013
ISO 15626:2011(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
COPYRIGHT PROTECTED DOCUMENT
© ISO 2011
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2011 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 15626:2013
ISO 15626:2011(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 15626 was prepared by CEN (as EN 15617) and was adopted, under a special “fast-track procedure”, by
Technical Committee ISO/TC 44, Welding and allied processes, Subcommittee SC 5, Testing and inspection
of welds, in parallel with its approval by the ISO member bodies.
Request for official interpretations of any aspect of ISO 15626 should be directed to the Secretariat of
ISO/TC 44/SC 5 via your national standards body. A complete listing of these bodies can be found at
www.iso.org.
© ISO 2011 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 15626:2013
---------------------- Page: 10 ----------------------
SIST EN ISO 15626:2013
INTERNATIONAL STANDARD ISO 15626:2011(E)
Non-destructive testing of welds — Time-of-flight diffraction
technique (TOFD) — Acceptance levels
1 Scope
This International Standard specifies acceptance levels for the time-of-flight diffraction technique (TOFD) of
full penetration welds in ferritic steels from 6 mm up to 300 mm thickness which correspond to the quality levels
of ISO 5817.
These acceptance levels are applicable to indications classified in accordance with ISO 10863.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 5817, Welding — Fusion-welded joints in steel, nickel, titanium and their alloys (beam welding
excluded) — Quality levels for imperfections (ISO 5817:2003, corrected version:2005, including Technical
Corrigendum 1:2006)
ISO 10863, Non-destructive testing of welds — Ultrasonic testing — Use of time-of-flight diffraction technique
1)
(TOFD)
3 Symbols, terms and definitions
3.1 Symbols
h height of an indication (see Figures 1, 2 and 3)
l length of an indication (see Figures 1, 2 and 3)
t nominal wall thickness in accordance with construction drawing or dimension table
(see Figures 1, 2 and 3)
3.2 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.2.1
embedded discontinuity
discontinuity within the volume of the material, separated from the surfaces
3.2.2
surface-breaking discontinuity
discontinuity connected to the near (contact) surface or far (reflecting) surface
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.