SIST EN 10162:2003
(Main)Cold rolled steel sections - Technical delivery conditions - Dimensional and cross-sectional tolerances
Cold rolled steel sections - Technical delivery conditions - Dimensional and cross-sectional tolerances
This European Standard specifies dimensional and cross-sectional tolerances for cold rolled steel sections produced on roll-forming machines.
It applies to cold-rolled sections for general use (standard sections) produced from steels conforming to EN 10025, EN 10142 and EN 10147 and in the form of rectangular L, U, C, Z and Omega cross sections as well as split tubes (see Figures 1 to 6).
It also applies to cold rolled sections for special applications (special sections) produced from steels listed in clause 5 with other radii, tolerances and shapes.
NOTE Examples of special sections are sections for steel-framed buildings, door frames and sections for rolling stock, automobiles and bridge engineering (see Figures 7 and 8).
This European Standard does not apply to drawn, pressed or folded cold formed sections, cold rolled steel piling or sections manufactured on the basis of special standards.
Kaltprofile aus Stahl - Technische Lieferbedingungen - Grenzabmaße und Formtoleranzen
Diese Europäische Norm legt die Maße und die Formtoleranzen für auf Walzprofiliermaschinen hergestellte Kaltprofile fest.
Sie ist anwendbar auf Kaltprofile für allgemeine Verwendung (Regelprofile) aus Stählen nach EN 10025, EN 10142 und EN 10147 und mit rechtwinkligem L-, U-, C-, Z- oder W-förmigem Querschnitt sowie Schlitzrohre (siehe Bilder 1 bis 6).
Sie ist ebenso anwendbar auf Kaltprofile für besondere Verwendung (Sonderprofile), hergestellt aus Stählen nach Abschnitt 5 mit anderen Radien, Grenzabmaßen und Formen.
ANMERKUNG Beispiele für Sonderprofile sind Profile für Stahlskelettbauten, Türrahmenprofile, Profile für den Waggon-, Automobil- und Brückenbau (siehe Bilder 7 und 8).
Diese Europäische Norm gilt nicht für gezogene, gepresste und abgekantete Profile oder für kaltprofilierte Spundbohlen, ferner nicht für Profile, die nach besonderer Norm hergestellt werden.
Profilés en acier formés a froid - Conditions techniques de livraison - Tolérances dimensionnelles et sur sections transversales
La présente Norme européenne spécifie les tolérances sur les dimensions et sections droites des profilés en acier formés a froid produits sur des machines a profiler.
Elle s'applique aux profilés froid d'usage général (profilés standards) produits a partir d'aciers conformes aux normes EN 10025, EN 10142 et EN 10147 et comportant une section droite en L, U, C, Z et Oméga de meme qu'aux profilés tubulaires a bords rejoints (voir Figures 1 a 6).
Elle s'applique également aux profilés a froid pour applications particulieres (profilés spéciaux) fabriqués a partir d'aciers listés dans l'article 5 avec d'autres rayons, formes et tolérances.
NOTE Des exemples de profilés spéciaux sont les profilés pour bâtiments a ossature métallique, dormants de portes, profilés pour matériel ferroviaire roulant, profilés pour ingéniérie du domaine automobile ou celui des ponts, etc? (voir Figures 7 et 8).
La présente Norme européenne ne s'applique pas aux profilés formés a froid pour étirage, emboutissage ou pliage ni aux palplanches en acier formées a froid, ni aux profilés fabriqués conformément a une norme spécifique.
Hladno valjani jekleni profili – Tehnični dobavni pogoji – Odstopki mer in prerezov
General Information
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Kaltprofile aus Stahl - Technische Lieferbedingungen - Grenzabmaße und FormtoleranzenProfilés en acier formés a froid - Conditions techniques de livraison - Tolérances dimensionnelles et sur sections transversalesCold rolled steel sections - Technical delivery conditions - Dimensional and cross-sectional tolerances77.140.70Jekleni profiliSteel profilesICS:Ta slovenski standard je istoveten z:EN 10162:2003SIST EN 10162:2003en01-november-2003SIST EN 10162:2003SLOVENSKI
STANDARD
SIST EN 10162:2003
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 10162April 2003ICS 77.140.70English versionCold rolled steel sections - Technical delivery conditions -Dimensional and cross-sectional tolerancesProfilés en acier formés à froid - Conditions techniques delivraison - Tolérances dimensionnelles et sur sectionstransversalesKaltprofile aus Stahl - Technische Lieferbedingungen -Grenzabmaße und FormtoleranzenThis European Standard was approved by CEN on 21 February 2003.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and UnitedKingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2003 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 10162:2003 ESIST EN 10162:2003
EN 10162:2003 (E)2ContentspageForeword.41Scope.52Normative references.53Terms and definitions.74Designation.74.1Designation of cold rolled sections for general applications.74.1.1General.74.1.2Section details.74.1.3Designation of split tubes.74.1.4Designation examples.94.2Designation of cold rolled sections for special applications.95Steel grades.96Delivery conditions.96.1Supply condition.96.2Edge condition.96.3Lengths.106.4End condition.106.5Delivered quantities.107Requirements.107.1Mechanical and technological properties.107.2Surface condition.107.3Nominal dimensions.117.3.1Cross sectional dimensions.117.3.2Internal bending radii.117.4Permitted dimensional and cross-sectional tolerances.117.4.1General.117.4.2Thickness.117.4.3Cross section.117.4.4Length.127.4.5Straightness.137.4.6Twist.137.4.7Concavity, convexity.137.5Mass.147.6Gross-cross-sectional characteristics.148Further processing.149Test requirements.149.1Number of test samples.149.2Test procedure.159.2.1Mechanical and technological characteristics.159.2.2Dimensions.159.2.3Surface condition.159.3Retests.159.4Material test certificates.1510Identification, marking.1511Packing.1612Protection of surfaces, storage and transport.1613Complaints.16SIST EN 10162:2003
EN 10162:2003 (E)314Ordering information.17Annex A (normative)
Inside bending radii.18Annex B (informative)
Further processing.20Bibliography.21SIST EN 10162:2003
EN 10162:2003 (E)4ForewordThis document (EN 10162:2003) has been prepared by Technical Committee ECISS /TC 13 "Flat products for coldworking - Qualities, dimensions, tolerances and specific tests" the secretariat of which is held by IBN.This European Standard shall be given the status of a national standard, either by publication of an identical text orby endorsement, at the latest by October 2003, and conflicting national standards shall be withdrawn at the latestby October 2003.Annex A is normative and annex B is informative.According to the CEN/CENELEC Internal Regulations, the national standards organizations of the followingcountries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal,Slovakia, Spain, Sweden, Switzerland and the United Kingdom.SIST EN 10162:2003
EN 10162:2003 (E)51 ScopeThis European Standard specifies dimensional and cross-sectional tolerances for cold rolled steel sections producedon roll-forming machines.It applies to cold-rolled sections for general use (standard sections) produced from steels conforming to EN 10025,EN 10142 and EN 10147 and in the form of rectangular L, U, C, Z and Omega cross sections as well as split tubes(see Figures 1 to 6).It also applies to cold rolled sections for special applications (special sections) produced from steels listed in clause 5with other radii, tolerances and shapes.NOTEExamples of special sections are sections for steel-framed buildings, door frames and sections for rolling stock,automobiles and bridge engineering (see Figures 7 and 8).This European Standard does not apply to drawn, pressed or folded cold formed sections, cold rolled steel piling orsections manufactured on the basis of special standards.2 Normative referencesThis European Standard incorporates by dated or undated reference, provisions from other publications. Thesenormative references are cited at the appropriate places in the text, and the publications are listed hereafter. Fordated references, subsequent amendments to or revisions of any of these publications apply to this EuropeanStandard only when incorporated in it by amendment or revision. For undated references the latest edition of thepublication referred to applies (including amendments).ENV 606, Bar coded transport and handling labels for steel productsEN 10002-1, Metallic materials - Tensile testing - Part 1: Method of test at ambient temperatureEN 10020:2000, Definition and classification of grades of steelEN 10021:1993, General technical delivery requirements for steel and iron productsEN 10025, Hot-rolled products of non-alloy structural steels - Technical delivery conditionsprEN 10025-2, Hot-rolled products of structural steels – Part 2: Technical delivery conditions for non-alloy structuralsteelsEN 10029, Hot rolled steel plates 3 mm thick or above - Tolerances on dimensions, shape and massEN 10045-1, Metallic materials - Charpy impact test - Part 1: Test methodEN 10048, Hot rolled narrow steel strip - Tolerances on dimensions and shapeEN 10051, Continuously hot-rolled uncoated plate, sheet and strip of non-alloy and alloy steels - Tolerances ondimensions and shapeEN 10079:1992, Definition of steel productsEN 10088-1, Stainless steels - Part 1: List of stainless steelsEN 10088-2, Stainless steels – Part 2: Technical delivery conditions for sheet / plate and strip for general purposesEN 10111, Continuously hot-rolled low carbon steel sheet and strip for cold forming - Technical delivery conditionsEN 10113-1, Hot rolled products in weldable fine grain structural steels - Part 1: General delivery conditionsSIST EN 10162:2003
EN 10162:2003 (E)6EN 10113-2, Hot rolled products in weldable fine grain structural steels - Part 2: Delivery conditions fornormalized/normalized rolled steelsEN 10113-3, Hot rolled products in weldable fine grain structural steels - Part 3: Delivery conditions forthermomechanical rolled steelsEN 10130, Cold rolled low carbon steel flat products for cold forming - Technical delivery conditionsEN 10131, Cold rolled uncoated low carbon and high yield strength steel flat products for cold forming - Toleranceson dimensions and shapeEN 10139, Cold rolled uncoated mild steel narrow strip for cold forming - Technical delivery conditionsEN 10140, Cold rolled narrow steel strip - Tolerances on dimensions and shapeEN 10142, Continuously hot-dip zinc coated low carbon steel strip and sheet for cold forming - Technical deliveryconditionsEN 10143, Continuously hot-dip metal coated steel sheet and strip - Tolerances on dimensions and shapeEN 10147, Continuously hot-dip zinc coated structural steel strip and sheet - Technical delivery conditionsEN 10152, Electrolytically zinc coated cold rolled steel flat products - Technical delivery conditionsEN 10154, Continuously hot-dip Aluminium-Silicon (AS) coated steel strip and sheet - Technical delivery conditionsEN 10169-1, Continuously organic coated (coil coated) steel flat products - Part 1: General information (definitions,material, tolerances, test methods)ENV 10169-2, Continuously organic coated (coil coated) steel flat products - Part 2: Products for building exteriorapplicationsEN 10204:1991, Metallic products - Types of inspection documentsEN 10214, Continuously hot-dip zinc-aluminium (ZA) coated steel strip and sheet - Technical delivery conditionsEN 10215, Continuously hot-dip aluminium-zinc (AZ) coated steel strip and sheet - Technical delivery conditionsEN 10258, Cold rolled stainless steel and narrow strip and cut lengths – Tolerances on dimensions and shapeEN 10259, Cold rolled stainless steel wide strip and plate / sheet – Tolerances on dimensions and shapeCR 10260, Designation systems for steel - Additional symbolsEN 10268, Cold-rolled flat products made of high yield strength micro-alloyed steels for cold forming - Generaldelivery conditionsEN ISO 377:1997, Steel and steel products - Location and preparation of samples and test pieces for mechanicaltesting (ISO 377:1997)EN ISO 14284:2002, Steel and Iron - Sampling and preparation of samples for the determination of chemicalcomposition (ISO 14284:1996).SIST EN 10162:2003
EN 10162:2003 (E)73 Terms and definitionsFor the purposes of this European Standard, the terms and definitions given in EN 10020:2000, EN 10021:1993,EN 10079:1992, EN 10204:1991, EN ISO 377:1997, EN ISO 14284:2002 and the following apply:3.1cold rolled sectionsproducts of various shapes having a constant cross section over their entire length. They are produced from hot orcold rolled flat products (with or without surface coatings) by purely cold forming without significantly affecting thethickness of the original flat product (e.g. by cold rolling, drawing, pressing, pressbreaking)3.2split tubecold rolled steel section which is not produced from a tube4 Designation4.1 Designation of cold rolled sections for general applications4.1.1 GeneralStandard sections shall be designated in accordance with 4.1.2 and 4.1.3.NOTEThe designation of standard sections does not require drawings.4.1.2 Section detailsFor a complete designation of rectangular cold rolled sections the following details shall be given in the indicatedsequence (see Figures 1 to 6):a) description of the form of the section (e.g. L, U, C, Z, Omega or split tube);b) all side lengths in chain (outer dimensions see Figures 1 to 6). In case the width of flanges or lips of a sectionare unequal the larger one shall be stated first. For split tubes, see 4.1.3;c) wall thickness in mm (separated from the side dimensions by a multiplication sign x);d) ID letters for the required edge, (NK = mill edge, GK = sheared edge; see also 6.2);e) length description (standard, fixed or exact lengths) ;f) length in mm when fixed or exact lengths of section are to be supplied (see 6.3 and 7.4.3);g) number of the present standard EN 10162;h) designation of the steel grade or the steel number (see clause 5);i) number of the European Standard which covers the steel grade under h).4.1.3 Designation of split tubesIn the case of split tubes dimension of height and width shall be stated only once (see example in 4.1.4 d).NOTEThis assumes that the gap is in the middle of a narrow side and the width of the gap does not exceed 1 x t (t = wall thickness).Details of the designation of other split tubes are given in 4.2.SIST EN 10162:2003
EN 10162:2003 (E)8Dimensions in millimetresFigure 1Figure 2Figure 3Figure 4Figure 5Figure 6Figures 1 to 6: Examples of cold rolled steel sections and their designationsDimensions in millimetresFigure 7Figure 8Figures 7 and 8: Examples of cold rolled steel sections for special applicationsSIST EN 10162:2003
EN 10162:2003 (E)94.1.4 Designation examplesDesignations shall be made as follows:a) channel section (U section) as per Figure 2 supplied in standard length and manufactured from S235JRG2(1.0038) steel conforming to EN 10025:U 50/100/50 x 5 standard length EN 10162 S235JRG2 (1.0038) EN 10025b) C section as show in Figure 3 with sheared edges, supplied in exact lengths of 3500 mm, manufactured fromsteel DC03 A (1.0347) conforming to EN 10130:C 20/40/90/40/15 x 2 GK x exact length 3 500 EN 10162 DC03 A (1.0347) EN 10130c) ‘Omega’ section as per Figure 5 with sheared edges, supplied in standard lengths, manufactured fromgalvanised steel DX52
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.