SIST EN 860:2009+A2:2012
(Main)Safety of woodworking machines - One side thickness planing machines
Safety of woodworking machines - One side thickness planing machines
This document specifies all significant hazards, hazardous situations and events as listed in Clause 4, relevant to stationary and displaceable one side thickness planing machines fitted with an integrated feed and with cutterblock fixed in position and manual loading and unloading of the work-piece, hereinafter referred to as "machines", designed to cut solid wood, chipboard, fibreboard and plywood when they are used as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse. Machines which are designed to work wood based materials may also be used for working hardened plastic materials with similar physical characteristics as wood. This document does not apply to: a) machines set up on a bench or a table similar to a bench, which is intended to carry out work in a stationary position, capable of being lifted by one person by hand; b) hand held planers or any adaptation permitting their use in a different mode, i.e. bench mounting; c) thickness planing machines where the cutterblock is adjustable for depth of cut setting. This document is not applicable to one side thickness planning machines fitted with an integrated feed and with cutterblock fixed in position which are manufactured before the date of its publication as EN.
Sicherheit von Holzbearbeitungsmaschinen - Dickenhobelmaschinen für einseitige Bearbeitung
Dieses Dokument !legt alle in Abschnitt 4" aufgeführten signifikanten Gefährdungen, Gefährdungs-situationen und Gefährdungsereignisse fest, die auf stationäre und verschiebbare Dickenhobelmaschinen für ein¬seitige Bearbeitung, die mit mechanischem Vorschub und mit Messerwelle in fester Lage ausgerüstet sind und mit Werkstückaufgabe und Werkstückabnahme von Hand zutreffen, im Folgenden als „Maschinen“ bezeichnet, die konstruiert sind zum Hobeln von Massivholz, Spanplatten, Faserplatten und Sperr¬holz, wenn sie bestimmungsgemäß und entsprechend den vorhersehbaren Bedingungen des Herstellers, #einschließlich vernünftigerweise vorhersehbarem Fehlverhalten$, ver¬wendet werden.
#Maschinen, die zur Bearbeitung von auf Holz basierenden Werkstoffen konstruiert sind, können auch für die Bearbeitung von Hartkunststoffen mit ähnlichen physikalischen Eigenschaften wie Holz verwendet werden.$
Dieses Dokument gilt nicht für:
a) Maschinen, die auf ein Gestell oder auf einen Tisch, der einem Gestell ähnlich ist, aufgesetzt sind und die vorgesehen sind, während des Betriebs stationär verwendet zu werden und die von einer Person von Hand angehoben werden können;
ANMERKUNG 1 Transportable elektrisch angetriebene Werkzeuge sind in #EN 61029-1:2009$ zusammen mit #EN 61029 2 3:2011$ behandelt.
b) handgeführte Hobelmaschinen einschließlich solcher Einrichtungen, die ihre Verwendung in einer anderen Weise, z. B. Einbau in einem Gestell, ermöglichen;
ANMERKUNG 2 Handgeführte elektrisch angetriebene Werkzeuge sind in #EN 60745 1:2009$ zusammen mit #EN 60745 2 14:2009$ behandelt.
c) Dickenhobelmaschinen, bei denen die Messerwelle für die Spanabnahme verstellt werden kann.
Dieses Dokument gilt nicht für Dickenhobelmaschinen für einseitige Bearbeitung, die mit mechanischem Vor¬schub und mit Messerwelle in fester Lage ausgerüstet sind, die vor dem Datum seiner Veröffentlichung als EN her¬gestellt wurden.
ANMERKUNG 3 Die in dieser Europäischen Norm behandelten Maschinen sind unter #3 des Anhangs IV$ der Maschinen¬richtlinie genannt.
Sécurité des machines pour le travail du bois - Machines à raboter sur une face
Le présent document !spécifie tous les phénomènes" dangereux, situations et événements dangereux significatifs, tels qu’énumérées à l'Article 4, applicables aux machines fixes et transportables à raboter sur une face à avance intégrée, à porte-outil fixe en position et à chargement/déchargement manuel de la pièce (désignées ci-après sous le terme "machines"). Celles-ci sont conçues pour usiner du bois massif, des panneaux de fibres ou de particules ou de contre plaqué durant l’utilisation normale et dans les conditions envisagées par le fabricant #incluant une mauvaise utilisation raisonnablement prévisible.
#Les machines qui sont conçues pour travailler les matériaux à base de bois peuvent également être utilisées pour travailler les matériaux en plastique durci ayant des caractéristiques physiques similaires à celles du bois.$
Le présent document ne s’applique pas :
a) aux machines montées sur un établi ou une table similaire à un établi, conçues pour réaliser un travail en position fixe, capables d’être soulevées à la main par une personne ;
NOTE 1 Les machines-outils électriques semi-fixes sont traités dans l'EN 61029-1:2009 ainsi que dans l’EN 61029-2-3:2011.
b) aux raboteuses portatives ou toute adaptation permettant leur utilisation dans un mode différent, par exemple, montées sur un bâti ;
NOTE 2 Les outils électroportatifs à moteur sont traités dans l'EN 60745-1:2009 ainsi que dans l'EN 60745-2-14:2009.
c) aux machines à raboter sur une face à porte-outil réglable en position pour le réglage de la profondeur de passe.
Le présent document ne s’applique pas aux machines à raboter sur une face à avance intégrée et à porte outil fixe en position fabriquées avant la date de sa publication comme EN.
NOTE 3 Les machines couvertes par la présente Norme européenne figurent en 3 de l’Annexe IV de la directive «Machines».
Varnost lesnoobdelovalnih strojev - Debelinski skobeljni strojii za enostransko obdelavo (vključno z dopolnili do A2)
Ta dokument določa vse večje nevarnosti, nevarne razmere in dogodke iz točke 4 v zvezi s stacionarnimi in premičnimi debelinskimi skobeljnimi stroji za enostransko obdelavo z vgrajenim podajalnikom in zanesljivo pritrjeno rezalno glavo ter ročnim nalaganjem in razlaganjem obdelovanca (v nadaljevanju: »stroji«), ki so namenjeni rezanju polnega lesa, ivernih plošč, vlaknenih plošč in vezanih plošč ter se uporabljajo v skladu z namenom in pod pogoji, ki jih je predvidel proizvajalec, vključno z razumno predvideno nepravilno uporabo. Stroji, namenjeni za obdelavo materialov na osnovi lesa, se lahko uporabljajo tudi za obdelavo trdih plastičnih materialov, ki imajo podobne fizikalne lastnosti kot les. Ta dokument se ne uporablja za: a) stroje, postavljene na klop ali mizo, podobno klopi, ki so namenjeni izvajanju dela v stacionarnem položaju in ki jih lahko ročno dvigne ena oseba; b) ročne skobelnike ali kakršno koli prilagoditev, ki omogoča, da se uporabljajo na drugačen način, tj. pritrditev na klop; c) debelinske skobeljne stroje, pri katerih se rezalna glava lahko prilagodi globini nastavitve rezanja. Ta dokument se ne uporablja za debelinske skobeljne stroje za enostransko obdelavo z vgrajenim podajalnikom in zanesljivo pritrjeno rezalno glavo, ki so bili izdelani, preden je bil objavljen kot standard EN.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 860:2009+A2:2012
01-september-2012
1DGRPHãþD
SIST EN 860:2009+A1:2009
9DUQRVWOHVQRREGHORYDOQLKVWURMHY'HEHOLQVNLVNREHOMQLVWURMLL]DHQRVWUDQVNR
REGHODYR YNOMXþQR]GRSROQLOLGR$
Safety of woodworking machines - One side thickness planing machines
Sicherheit von Holzbearbeitungsmaschinen - Dickenhobelmaschinen für einseitige
Bearbeitung
Sécurité des machines pour le travail du bois - Machines à raboter sur une face
Ta slovenski standard je istoveten z: EN 860:2007+A2:2012
ICS:
25.080.25 6WURML]DSORãþLQVNRREGHODYR Planing machines
79.120.10 Lesnoobdelovalni stroji Woodworking machines
SIST EN 860:2009+A2:2012 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 860:2009+A2:2012
---------------------- Page: 2 ----------------------
SIST EN 860:2009+A2:2012
EUROPEAN STANDARD
EN 860:2007+A2
NORME EUROPÉENNE
EUROPÄISCHE NORM
June 2012
ICS 79.120.10 Supersedes EN 860:2007+A1:2009
English Version
Safety of woodworking machines - One side thickness planing
machines
Sécurité des machines pour le travail du bois - Machines à Sicherheit von Holzbearbeitungsmaschinen -
raboter sur une face Dickenhobelmaschinen für einseitige Bearbeitung
This European Standard was approved by CEN on 10 May 2007 and includes Amendment 1 approved by CEN on 16 July 2009 and
Amendment 2 approved by CEN on 20 May 2012.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2012 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 860:2007+A2:2012: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 860:2009+A2:2012
EN 860:2007+A2:2012 (E)
Contents Page
Foreword .4
Introduction .5
1 Scope .6
2 Normative references .6
3 Terms and definitions .8
3.1 General .8
3.2 Definitions .8
3.3 Terms . 11
4 List of significant hazards . 12
5 Safety requirements and/or measures . 15
5.1 General . 15
5.2 Controls . 15
5.2.1 Safety and reliability of control systems . 15
5.2.2 Position of controls . 16
5.2.3 Starting . 16
5.2.4 Normal stopping . 17
5.2.5 Emergency stop . 17
5.2.6 Failure of the power supply . 18
5.2.7 Failure of the control circuit . 18
5.3 Protection against mechanical hazards . 19
5.3.1 Stability . 19
5.3.2 Hazard of break up during operation . 19
5.3.3 Cutterblock design . 19
5.3.4 Braking . 19
5.3.5 Devices to minimise the possibility or the effect of ejection . 20
5.3.6 Work-piece support and guides . 21
5.3.7 Prevention of access to moving parts . 22
5.3.8 Characteristics of ##cutterblock$$ guards . 23
## $$
5.4 Protection against non-mechanical hazards . 23
5.4.1 Fire . 23
5.4.2 Noise . 23
5.4.3 Emission of chips and dust . 24
5.4.4 Electricity . 25
5.4.5 Ergonomics and handling . 26
5.4.6 Pneumatics . 27
5.4.7 Hydraulics . 27
5.4.8 Electromagnetic compatibility . 27
5.4.9 Supply disconnection (isolation) . 27
5.4.10 Static electricity . 28
5.4.11 Maintenance . 28
6 Information for use . 28
6.1 General . 28
6.2 Marking . 28
6.3 Instruction handbook . 29
Annex A (normative) Kickback test . 33
Annex B (normative) Stability test for displaceable machines . 34
Annex C (normative) Impact test method for guards . 35
2
---------------------- Page: 4 ----------------------
SIST EN 860:2009+A2:2012
EN 860:2007+A2:2012 (E)
C.1 General . 35
C.2 Test method . 35
C.2.1 Preliminary remarks . 35
C.2.2 Testing equipment . 35
C.2.3 Projectile for guards . 35
C.2.4 Sampling. 35
C.2.5 Test procedure . 35
C.3 Results . 36
C.4 Assessment . 36
C.5 Test report . 36
C.6 Test equipment for impact test . 36
Annex D (normative) Braking tests . 40
D.1 Conditions for all tests . 40
D.2 # #Un-braked$$ run-down time . 40
## $$
D.3 Braked run-down time . 40
Annex ZA (informative) !Relationship between this European Standard and the Essential
Requirements of EU Directive 2006/42/EC"""" . 42
Bibliography . 46
3
---------------------- Page: 5 ----------------------
SIST EN 860:2009+A2:2012
EN 860:2007+A2:2012 (E)
Foreword
This document (EN 860:2007+A2:2012) has been prepared by Technical Committee CEN/TC 142
“Woodworking machines - Safety”, the secretariat of which is held by UNI.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by December 2012, and conflicting national standards shall be withdrawn
at the latest by December 2012.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document includes Amendment 1, approved by CEN on 2009-07-16 and Amendment 2, approved by
CEN on 2012-05-20.
This document supersedes #EN 860:2007+A1:2009$.
The start and finish of text introduced or altered by amendment is indicated in the text by tags ! " and
#$.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of the Machinery Directive.
#For relationship with EU Directive, see informative Annex ZA, which is an integral part of this document.$
Organisation contributing to the preparation of the European Standard include the European Association of
Manufacturer of Woodworking Machines "EUMABOIS".
The European Standards produced by CEN/TC 142 are particular to woodworking machines and complement
the relevant A and B standards on the subject of general safety (see introduction of
#EN ISO 12100:2010$ for a description of A, B and C standards).
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland, Turkey and the United Kingdom.
4
---------------------- Page: 6 ----------------------
SIST EN 860:2009+A2:2012
EN 860:2007+A2:2012 (E)
Introduction
This document has been prepared to be a harmonised standard to provide one means of conforming to the
essential safety requirements of the Machinery Directive, and associated EFTA regulations.
This document is a type C standard as defined in #EN ISO 12100:2010$.
The machinery concerned and the extent to which hazards, hazardous situations and events are covered are
indicated in the scope of this document.
When provisions of this type C standard are different from those which are stated in type A or B standards, the
provisions of this type C standard take precedence over the provisions of other standards, for machines that
have been designed and built according to the provisions of this type C standard.
The requirements of this document are directed to manufacturers and their authorised representatives of one
side thickness planing machines. They are also useful for designers and importers.
This document also includes provisions and examples of information to be provided by the manufacturer to
the user.
Common requirements for tooling are given in #EN 847-1:2005+A1:2007$.
5
---------------------- Page: 7 ----------------------
SIST EN 860:2009+A2:2012
EN 860:2007+A2:2012 (E)
1 Scope
This document !specifies all significant" hazards, hazardous situations and events as listed in Clause 4,
relevant to stationary and displaceable one side thickness planing machines fitted with an integrated feed and
with cutterblock fixed in position and manual loading and unloading of the work-piece, hereinafter referred to
as "machines", designed to cut solid wood, chipboard, fibreboard and plywood when they are used as
intended and under the conditions foreseen by the manufacturer #including reasonably foreseeable
misuse$.
#Machines which are designed to work wood based materials may also be used for working hardened
plastic materials with similar physical characteristics as wood.$
This document does not apply to:
a) machines set up on a bench or a table similar to a bench, which is intended to carry out work in a
stationary position, capable of being lifted by one person by hand;
NOTE 1 Transportable motor-operated electric tools are dealt with in #EN 61029-1:2009$ together with
#EN 61029-2-3:2011$.
b) hand held planers or any adaptation permitting their use in a different mode, i.e. bench mounting;
NOTE 2 Hand-held motor-operated electric tools are dealt with in #EN 60745-1:2009$ together with
#EN 60745-2-14:2009$.
c) thickness planing machines where the cutterblock is adjustable for depth of cut setting.
This document is not applicable to one side thickness planning machines fitted with an integrated feed and
with cutterblock fixed in position which are manufactured before the date of its publication as EN.
NOTE 3 Machines covered by this European Standard are listed under #3 of Annex IV$ of the Machinery Directive.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
#EN 847-1:2005+A1:2007$, Tools for woodworking — Safety requirements — Part 1: Milling tools,
circular saw blades
#deleted text$
#EN 1005-4:2005+A1:2008$, Safety of machinery — Human physical performance — Part 4: Evaluation
of working postures and movements in relation to machinery
#EN 1037:1995+A1:2008$, Safety of machinery — Prevention of unexpected start-up
#EN 1088:1995+A2:2008$, Safety of machinery — Interlocking devices associated with guards —
Principles for design and selection
EN 50178:1997, Electronic equipment for use in power installations
EN 50370-1:2005, Electromagnetic compatibility (EMC) — Product family standard for machine tools —
Part 1: Emission
6
---------------------- Page: 8 ----------------------
SIST EN 860:2009+A2:2012
EN 860:2007+A2:2012 (E)
EN 50370-2:2003, Electromagnetic compatibility (EMC) — Product family standard for machine tools —
Part 2: Immunity
EN 60204-1:2006, Safety of machinery — Electrical equipment of machines — Part 1: General requirements
(IEC 60204-1:2005, modified)
1)
EN 60439-1:1999 , Low-voltage switchgear and controlgear assemblies — Part 1: Type-tested and partially
type-tested assemblies (IEC 60439-1:1999)
2)
EN 60529:1991 , Degrees of protection provided by enclosures (IP code) (IEC 60529:1989)
EN 61496-1:2004, Safety of machinery — Electro-sensitive protective equipment — Part 1: General
requirements and tests (IEC 61496-1:2004, modified)
#deleted text$
#EN 61800-5-2:2007, Adjustable speed electrical power drive systems — Part 5-2: Safety requirements —
Functional (IEC 61800-5-2:2007)$
#EN ISO 3743-1:2010$, #Acoustics — Determination of sound power levels and sound energy levels of
noise sources using sound pressure — Engineering methods for small movable sources in reverberant fields
— Part 1: Comparison method for a hard-walled test room (ISO 3743-1:2010)$
#EN ISO 3743-2:2009$, Acoustics — Determination of sound power levels of noise sources using sound
pressure — Engineering methods for small, movable sources in reverberant fields — Part 2: Methods for
special reverberant test rooms (ISO 3743-2:1994)
#EN ISO 3744:2010$, #Acoustics — Determination of sound power levels and sound energy levels of
noise sources using sound pressure — Engineering methods for an essentially free field over a reflecting
plane (ISO 3744:2010)$
#EN ISO 3745:2009$, Acoustics — Determination of sound power levels of noise sources using sound
pressure — Precision methods for anechoic and semi-anechoic rooms (ISO 3745:2003)
#EN ISO 3746:2010$, #Acoustics — Determination of sound power levels and sound energy levels of
noise sources using sound pressure — Survey method using an enveloping measurement surface over a
reflecting plane (ISO 3746:2010)$
#EN ISO 4413:2010, Hydraulic fluid power — General rules and safety requirements for systems and their
components (ISO 4413:2010)
EN ISO 4414:2010, Pneumatic fluid power — General rules and safety requirements for systems and their
components (ISO 4414:2010)$
#EN ISO 4871:2009$, Acoustics — Declaration and verification of noise emission values of machinery
and equipment (ISO 4871:1996)
#EN ISO 9614-1:2009$, Acoustics — Determination of sound power levels of noise sources using sound
intensity — Part 1: Measurement at discrete points (ISO 9614-1:1993)
#EN ISO 11202:2010$, #Acoustics — Noise emitted by machinery and equipment — Determination of
emission sound pressure levels at a work station and at other specified positions applying approximate
environmental corrections (ISO 11202:2010)$
1)
#EN 60439-1:1999 is impacted by EN 60439-1:1999/A1:2004.$
2)
#EN 60529:1991 is impacted by EN 60529:1991/A1:2000.$
7
---------------------- Page: 9 ----------------------
SIST EN 860:2009+A2:2012
EN 860:2007+A2:2012 (E)
#EN ISO 11204:2010$, #Acoustics — Noise emitted by machinery and equipment — Determination of
emission sound pressure levels at a work station and at other specified positions applying accurate
environmental corrections (ISO 11204:2010)$
#EN ISO 11688-1:2009$, Acoustics — Recommended practice for the design of low-noise machinery and
equipment — Part 1: Planning (ISO/TR 11688-1:1995)
#EN ISO 12100:2010, Safety of machinery — General principles for design — Risk assessment and risk
reduction (ISO 12100:2010)$
)
3
!EN ISO 13849-1:2008" , Safety of machinery — Safety-related parts of control systems — Part 1:
General principles for design (ISO 13849-1:2006)
!EN ISO 13849-2:2008", Safety of machinery — Safety-related parts of control systems — Part 2:
Validation (ISO 13849-2:2003)
HD 22.4 S4:2004, Cables of rated voltages up to and including 450/750 V and having crosslinked insulation —
Part 4: Cords and flexible cables
ISO 7568:1986, Woodworking machines — Thickness planing machines with rotary cutterblock for one-side
dressing — Nomenclature and acceptance conditions
ISO 7960:1995, Airborne noise emitted by machine tools — Operating conditions for woodworking machines
3 Terms and definitions
3.1 General
For the purposes of this document, the terms and definitions given in #EN ISO 12100:2010$ and the
following apply:
3.2 Definitions
3.2.1
one side thickness planing machine
machine designed for cutting off layers of the upper surface of a work-piece by a cutterblock rotating around a
horizontal axis, mounted at right angles to the infeed direction above the table designed to position and
support the work-piece
NOTE The cutterblock is a cylindrical shaped complex tool equipped with blades with horizontal straight cutting line
that cuts while rotating (see also #EN 847-1:2005+A1:2007$ for a description of the complex tool). The work-piece is
fed into the machine against the direction of the cut
3.2.2
table
table used to support the work-piece at the machine which may comprise an assembly of rollers, belts or other
fixed or moving mechanical elements
3.2.3
cutterblock
machine component designed to hold the cutting knives or cutting blades
)
3
!EN ISO 13849-1:2006 superseded EN 954-1:1996."
8
---------------------- Page: 10 ----------------------
SIST EN 860:2009+A2:2012
EN 860:2007+A2:2012 (E)
3.2.4
tool
complex tool as defined in #EN 847-1:2005+A1:2007$ which consists of the cutterblock, the cutting
blades and their fixings
3.2.5
integrated feed
feed mechanism for the work-piece which is integrated with the machine and where the work-piece is held and
controlled mechanically during the machining operation
3.2.6
loading of a one side thicknessing machine
manual placing of the work-piece to an integrated feed device consisting in feed rollers
3.2.7
stationary machine
machine designed to be located on or fixed to the floor or other parts of the structure of the premises and to
be stationary during used
3.2.8
displaceable machine
machine which is located on the floor, stationary during use and equipped with a device, normally wheels,
which allows it to be moved between locations
3.2.9
kickback
particular form of ejection describing the uncontrolled movement of the work-piece or parts of it or parts of the
machine opposite to the direction of feed during processing
3.2.10
anti-kickback device
device which either reduces the possibility of kickback or arrests the motion during kickback of the work-piece
parts of it
3.2.11
run-down time
elapsed time from the actuation of the stop control device to cutterblock stand still
3.2.12
run-up time
elapsed time from the actuation of the start control device until the spindle reaches the actual speed related to
the intended speed
3.2.13
information from the supplier
statement, sales literature, leaflet or other documents in which a manufacturer (or supplier) declares either the
characteristics of e.g. a material or product or the conformity of the material or product to a relevant standard
3.2.14
machine actuator
power mechanism used to effect motion of the machine
#deleted text$
####3.2.15
embedded software (SRESW)
software that is part of the system supplied by the control manufacturer and which is not accessible for
modification by the user of the machinery.
9
---------------------- Page: 11 ----------------------
SIST EN 860:2009+A2:2012
EN 860:2007+A2:2012 (E)
NOTE 1 Firmware or system software are examples of embedded software (EN ISO 13849-1:2008, 3.1.37).$
NOTE 2 Manufacturer means manufacturer of the system.
NOTE 3 For example the operating system of a speed monitoring device.
####3.2.16
application software (SRASW)
software specific to the application, implemented by the machine manufacturer, and generally containing logic
sequences, limits and expressions that control the appropriate inputs, outputs, calculations and decisions
necessary to meet the SRP/CS requirements
[EN ISO 13849-1:2008, 3.1.36]$
####3.2.17$$$$
safety related part of a control system (SRP/CS)
part or subpart(s) of a control system that responds to #safety related$ input signals and generates
safety-related output signals.
#NOTE 1$ The combined safety-related parts of a control system start at the point where the safety-related signals are
initiated (including e.g. the actuating cam and the roller of the position switch) and end at the output of the power control
elements (including e.g. the main contacts of the contactor). This also includes monitoring systems (3.1 of
!EN ISO 13849-1:2008")
#NOTE 2 If monitoring systems are used for diagnostics, they are also considered as SRP/CS.
[EN ISO 13849-1:2008, 3.1.1]$
##3.2.18
##
performance level PL
discrete level used to specify the ability of safety-related parts of control systems to perform a safety function
under foreseeable conditions
[EN ISO 13849-1:2008, 3.1.23]$
10
---------------------- Page: 12 ----------------------
SIST EN 860:2009+A2:2012
EN 860:2007+A2:2012 (E)
3.3 Terms
The names of the main parts of the machine are shown in Figure 1 and Figure 2.
Key
1 infeed table
2 anti-kickback fingers
3 upper guard
4 controls panel
5 table lifting system
6 extraction hood
Figure 1 — Example of a one side thickness planing machine
11
---------------------- Page: 13 ----------------------
SIST EN 860:2009+A2:2012
EN 860:2007+A2:2012 (E)
Key
1 anti kickback fingers
2 stop for the rotation of the finger
3 infeed roller
4 outfeed roller
5 cutterblock
6 direction of feed
Figure 2 — Example of the internal of a one side thickness planing machine
4 List of significant hazards
This clause contains !all significant" hazards, hazardous situations and events (see
#EN ISO 12100:2010$), #deleted text$ identified by risk assessment as significant for the machines
as defined in the scope and which require action to eliminate or reduce the risk. This document deals with
these significant hazards by defining safety requirements and/ or measures or by reference to relevant
standards.
#These hazards are listed in Table 1:$
12
---------------------- Page: 14 ----------------------
SIST EN 860:2009+A2:2012
EN 860:2007+A2:2012 (E)
####
Table 1 — List of significant hazards
Hazards, hazardous situations and hazardous Relevant
No events EN ISO clause of this
12100:2010 document
1 Mechanical hazards related to:
- mach
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.