SIST EN ISO 15084:2003
(Main)Small craft - Anchoring, mooring and towing - Strong points (ISO 15084:2003)
Small craft - Anchoring, mooring and towing - Strong points (ISO 15084:2003)
ISO 15084:2003 specifies requirements for strong points for attaching chains, cables and lines for anchoring, mooring and towing small craft. It does not specify the requirement for the strong point from which the craft can tow other vessels. This standard is applicable to small craft with a hull length up to 24 m.
ISO 15084:2003 does not define anchor weights or the length of chains and lines.
Kleine Wasserfahrzeuge - Ankern, Festmachen und Schleppen - Festpunkte (ISO 15084:2003)
Diese Internationale Norm legt Anforderungen an Festpunkte fest, an denen Ketten, Trossen oder Leinen befestigt werden sollen, die dazu dienen, das kleine Wasserfahrzeug zu ankern, festzumachen oder zu schleppen. Die Norm betrifft nicht solche Festpunkte, von denen aus das Wasserfahrzeug andere Fahrzeuge schleppen kann. Die Norm gilt für kleine Wasserfahrzeuge bis 24 m Rumpflänge.
Diese Internationale Norm legt weder Gewichte von Ankern noch die Länge von Ketten und Leinen fest.
Petits navires - Mouillage, amarrage et remorquage - Points d'ancrage (ISO 15084:2003)
L'ISO 15084:2003 spécifie des exigences relatives aux points d'ancrage des chaînes, câbles et lignes de mouillage, d'amarrage et de remorquage du bateau. Elle ne spécifie pas d'exigence relative au point d'ancrage destiné au remorquage d'autres bateaux. La présente Norme internationale est applicable aux bateaux ayant une longueur de coque inférieure ou égale à 24 m.
L'ISO 15084:2003 ne définit pas la masse des ancres ni la longueur des chaînes ou des lignes.
Mala plovila - Sidranje, privez in vleka – Poudarki (ISO 15084:2003)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 15084:2003
01-december-2003
Mala plovila - Sidranje, privez in vleka – Poudarki (ISO 15084:2003)
Small craft - Anchoring, mooring and towing - Strong points (ISO 15084:2003)
Kleine Wasserfahrzeuge - Ankern, Festmachen und Schleppen - Festpunkte (ISO
15084:2003)
Petits navires - Mouillage, amarrage et remorquage - Points d'ancrage (ISO 15084:2003)
Ta slovenski standard je istoveten z: EN ISO 15084:2003
ICS:
47.080
SIST EN ISO 15084:2003 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
EUROPEAN STANDARD
EN ISO 15084
NORME EUROPÉENNE
EUROPÄISCHE NORM
February 2003
ICS 47.080
English version
Small craft - Anchoring, mooring and towing - Strong points (ISO
15084:2003)
Petits navires - Mouillage, amarrage et remorquage - Kleine Wasserfahrzeuge - Ankern, Festmachen und
Points d'ancrage (ISO 15084:2003) Schleppen - Festpunkte (ISO 15084:2003)
This European Standard was approved by CEN on 9 January 2003.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2003 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 15084:2003 E
worldwide for CEN national Members.
---------------------- Page: 2 ----------------------
EN ISO 15084:2003 (E)
CORRECTED 2003-04-30
Foreword
This document (EN ISO 15084:2003) has been prepared by Technical Committee ISO/TC 188 "Small
craft", the secretariat of which is held by CMC.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by August 2003, and conflicting national standards shall
be withdrawn at the latest by August 2003.
This document has been prepared under a mandate given to CEN by the European Commission and
the European Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see informative Annex ZB, which is an integral part of this
document.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Czech
Republic, Denmark, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Luxembourg,
Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 15084:2003 has been approved by CEN as EN ISO 15084:2003 without any
modifications.
NOTE Normative references to International Standards are listed in Annex ZA (normative).
2
---------------------- Page: 3 ----------------------
EN ISO 15084:2003 (E)
Annex ZA
(normative)
Normative references to international publications
with their relevant European publications
This European Standard incorporates by dated or undated reference, provisions from other publications.
These normative references are cited at the appropriate places in the text and the publications are listed
hereafter. For dated references, subsequent amendments to or revisions of any of these publications
apply to this European Standard only when incorporated in it by amendment or revision. For undated
references the latest edition of the publication referred to applies (including amendments).
NOTE Where an International Publication has been modified by common modifications, indicated by
(mod.), the relevant EN/HD applies.
Publication Year Title EN Year
ISO 8666 2002 Small craft - Principal data EN ISO 8666 2002
3
---------------------- Page: 4 ----------------------
EN ISO 15084:2003 (E)
Annex ZB
(informative)
Clauses of this European Standard addressing essential requirements or other
provisions of EU Directives
This European Standard has been prepared under a mandate given to CEN by the European
Commission and the European Free Trade Association and supports essential requirements of EU
Directive 94/25/EC.
WARNING Other requirements and other EU Directives may be applicable to the product(s)
falling within the scope of this standard.
The following clauses of this standard, as detailed in Table ZB.1, are likely to support requirements of
Directive 94/25/EEC.
Compliance with these clauses of this standard provides one means of conforming with the specific
essential requirements of the Directive concerned and associated EFTA regulations.
Table ZB.1— Correspondence between this European Standard and EU Directives
Clause/subclause of this European Corresponding Essential Requirement of
Standard Directive 94/25/EEC
Annex I, Clause 3.9
All clauses
Anchoring, mooring and towing
4
---------------------- Page: 5 ----------------------
INTERNATIONAL ISO
STANDARD 15084
First edition
2003-02-15
Small craft — Anchoring, mooring and
towing — Strong points
Petits navires — Mouillage, amarrage et remorquage — Points
d'ancrage
Reference number
ISO 15084:2003(E)
©
ISO 2003
---------------------- Page: 6 ----------------------
ISO 15084:2003(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2003
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2003 — All rights reserved
---------------------- Page: 7 ----------------------
ISO 15084:2003(E)
Contents Page
Foreword. iv
1 Scope. 1
2 Normative references . 1
3 Terms and definitions. 1
4 Symbols . 2
5 General requirements . 2
6 Strength requirements. 3
7 Detailed requirements . 4
8 Owner’s manual . 4
9 Strength of synthetic fibre ropes . 4
Annex A (normative) Information to be provided in the owner’s manual . 5
Annex B (informative) Material strength of synthetic fibre ropes/dimensions of strong points. 6
Bibliography . 7
© ISO 2003 — All rights reserved iii
---------------------- Page: 8 ----------------------
ISO 15084:2003(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of el
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.