EN ISO 19712-3:2022
(Main)Plastics - Decorative solid surfacing materials - Part 3: Determination of properties - Solid surface shapes (ISO 19712-3:2022)
Plastics - Decorative solid surfacing materials - Part 3: Determination of properties - Solid surface shapes (ISO 19712-3:2022)
This document specifies the methods of test for determination of the properties of solid surfacing materials, as defined in Clause 3, in the form of shaped products. These methods are primarily intended for testing the materials specified in ISO 19712-1.
The tests can be carried out on finished products, but are generally carried out on test panels of a size sufficient to meet the requirements of the test, and of the same material and finish as the finished product.
Kunststoffe - Dekorative Mineralwerkstoffe - Teil 3: Prüfverfahren - Formteile (ISO 19712-3:2022)
Dieses Dokument legt die Prüfverfahren zur Bestimmung der Eigenschaften von Mineralwerkstoffen fest, die wie in Abschnitt 3 definiert geformte Produkte sind. Diese Verfahren sind hauptsächlich zur Prüfung der in ISO 19712 1 festgelegten Werkstoffe vorgesehen.
Die Prüfungen können an fertigen Erzeugnissen durchgeführt werden, werden jedoch im Allgemeinen an Prüfplatten vorgenommen, deren Größe ausreichend ist, um die Prüfanforderungen zu erfüllen, und die aus dem gleichen Material bestehen und die gleiche Oberflächenbeschaffenheit aufweisen wie die fertigen Erzeugnisse.
SICHERHEITSVORKEHRUNGEN — Personen, die dieses Dokument anwenden, sollten gegebenenfalls mit der üblichen Laborpraxis vertraut sein. Dieses Dokument erhebt nicht den Anspruch, alle Sicherheitsprobleme zu behandeln, die gegebenenfalls mit seiner Anwendung verbunden sind. Es liegt in der Verantwortung des Anwenders, geeignete Vorkehrungen für den Arbeits- und Gesundheitsschutz und für die Einhaltung jeglicher gesetzlicher Bestimmungen zu treffen.
Plastiques - Matériaux décoratifs massifs de revêtement de surface - Partie 3: Détermination des propriétés - Produits mis en forme (ISO 19712-3:2022)
Le présent document spécifie les méthodes d'essai pour la détermination des propriétés des matériaux massifs de revêtement de surface sous forme de produits formés, tels que définis à l'Article 3. Ces méthodes sont principalement destinées à la réalisation des essais sur les matériaux spécifiés dans l'ISO 19712‑1.
Les essais peuvent être effectués sur des produits finis, mais ils sont généralement effectués sur des panneaux d'essai de taille suffisante pour répondre aux exigences de l'essai et réalisés à partir du même matériau et de la même finition que le produit fini.
Polimerni materiali - Dekorativni trdni površinski materiali - 3. del: Ugotavljanje lastnosti - Oblika (ISO 19712-3:2022)
Ta dokument določa preskusne metode za določanje lastnosti trdnih površinskih materialov oz. oblikovanih izdelkov, kot je opredeljeno v točki 3. Te metode so primarno namenjene preskušanju materialov, določenih v standardu ISO 19712-1. Preskuse je mogoče izvajati na končnih izdelkih, vendar se običajno izvajajo na preskusnih ploščah v taki velikosti, da izpolnjujejo zahteve preskusa, ter so iz istega materiala in končne obdelave kot končni izdelek.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 19712-3:2022
01-junij-2022
Nadomešča:
SIST EN ISO 19712-3:2014
Polimerni materiali - Dekorativni trdni površinski materiali - 3. del: Ugotavljanje
lastnosti - Oblika (ISO 19712-3:2022)
Plastics - Decorative solid surfacing materials - Part 3: Determination of properties -
Solid surface shapes (ISO 19712-3:2022)
Kunststoffe - Dekorative Mineralwerkstoffe - Teil 3: Prüfverfahren - Formteile (ISO 19712
-3:2022)
Plastiques - Matériaux décoratifs massifs de revêtement de surface - Partie 3:
Détermination des propriétés - Produits mis en forme (ISO 19712-3:2022)
Ta slovenski standard je istoveten z: EN ISO 19712-3:2022
ICS:
83.140.20 Laminatne plošče Laminated sheets
SIST EN ISO 19712-3:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 19712-3:2022
---------------------- Page: 2 ----------------------
SIST EN ISO 19712-3:2022
EN ISO 19712-3
EUROPEAN STANDARD
NORME EUROPÉENNE
April 2022
EUROPÄISCHE NORM
ICS 83.140.20 Supersedes EN ISO 19712-3:2013
English Version
Plastics - Decorative solid surfacing materials - Part 3:
Determination of properties - Solid surface shapes (ISO
19712-3:2022)
Plastiques - Matériaux décoratifs massifs de Kunststoffe - Dekorative Mineralwerkstoffe - Teil 3:
revêtement de surface - Partie 3: Détermination des Prüfverfahren - Formteile (ISO 19712-3:2022)
propriétés - Produits mis en forme (ISO 19712-3:2022)
This European Standard was approved by CEN on 18 March 2022.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 19712-3:2022 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 19712-3:2022
EN ISO 19712-3:2022 (E)
Contents Page
European foreword . 3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 19712-3:2022
EN ISO 19712-3:2022 (E)
European foreword
This document (EN ISO 19712-3:2022) has been prepared by Technical Committee ISO/TC 61 "Plastics"
in collaboration with Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by
NBN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by October 2022, and conflicting national standards shall
be withdrawn at the latest by October 2022.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 19712-3:2013.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 19712-3:2022 has been approved by CEN as EN ISO 19712-3:2022 without any
modificat
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.