SIST EN IEC 63138-1:2020
(Main)Multi-channel radio frequency connectors - Part 1: Generic specification - General requirements and test methods (IEC 63138-1:2019)
Multi-channel radio frequency connectors - Part 1: Generic specification - General requirements and test methods (IEC 63138-1:2019)
EN-IEC 63138-1, which is a generic specification, specifies general requirements for multi-channel radio-frequency connectors, including terms and definitions, design and construction, ratings and characteristics, climatic categories, IEC type designation, requirements and test procedures, quality assessment, marking, etc. It provides the basis for establishing the sectional specifications for various multichannel radiofrequency connector types. This document applies to multi-channel radio-frequency connectors (called "connectors", hereinafter) for use in communications, electronics and other equipment.
Mehrkanalige Hochfrequenz-Steckverbinder - Teil 1: Fachgrundspezifikation - Allgemeine Anforderungen und Prüfverfahren (IEC 63138-1:2019)
Connecteurs radiofréquences multicanaux - Partie 1: Spécification générique - Exigences générales et méthodes d'essai (IEC 63138-1:2019)
l'IEC 63138-1:2019, qui est une spécification générique, spécifie les exigences générales pour les connecteurs radiofréquences multicanaux, y compris les termes et définitions, la conception et la construction, les valeurs assignées et les caractéristiques, les catégories climatiques, la désignation de type IEC, les exigences et procédures d'essai, l'assurance de la qualité, le marquage, etc.
Elle fournit les bases pour l'établissement des spécifications intermédiaires relatives aux différents types de connecteurs radiofréquences multicanaux. Le présent document s'applique aux connecteurs radiofréquences multicanaux (ci-après dénommés les "connecteurs") destinés à être utilisés dans des équipements de communications, électroniques et autres.
Večkanalni radiofrekvenčni konektorji - 1. del: Splošna specifikacija - Splošne zahteve in merilne metode (IEC 63138-1:2019)
Standard EN-IEC 63138-1, ki je splošna specifikacija, določa splošne zahteve za večkanalne radiofrekvenčne konektorje, vključno z izrazi in opredelitvami, načrtovanjem in zasnovo, ocenami terznačilnostmi, klimatskimi kategorijami, oznakami tipov IEC, zahtevami in preskusnimi postopki, oceno kakovosti, označevanjem itd. To je osnova za določitev področnih specifikacij za različne tipe večkanalnih radiofrekvenčnih konektorjev. Ta dokument se uporablja za večkanalne radiofrekvenčne konektorje (v nadaljevanju »konektorji«) za uporabo v komunikacijah, elektroniki in drugi opremi.
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN IEC 63138-1:2020
01-januar-2020
Večkanalni radiofrekvenčni konektorji - 1. del: Splošna specifikacija - Splošne
zahteve in merilne metode (IEC 63138-1:2019)
Multi-channel radio frequency connectors - Part 1: Generic specification - General
requirements and test methods (IEC 63138-1:2019)
Mehrkanalige Hochfrequenz-Steckverbinder - Teil 1: Fachgrundspezifikation - Allgemeine
Anforderungen und Prüfverfahren (IEC 63138-1:2019)
Connecteurs radiofréquences multicanaux - Partie 1: Spécification générique -
Exigences générales et méthodes d'essai (IEC 63138-1:2019)
Ta slovenski standard je istoveten z: EN IEC 63138-1:2019
ICS:
33.120.30 Radiofrekvenčni konektorji RF connectors
(RF)
SIST EN IEC 63138-1:2020 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN IEC 63138-1:2020
---------------------- Page: 2 ----------------------
SIST EN IEC 63138-1:2020
EUROPEAN STANDARD EN IEC 63138-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
November 2019
ICS 33.120.30
English Version
Multi-channel radio frequency connectors - Part 1: Generic
specification - General requirements and test methods
(IEC 63138-1:2019)
Connecteurs radiofréquences multicanaux - Partie 1: Mehrkanalige Hochfrequenz-Steckverbinder - Teil 1:
Spécification générique - Exigences générales et méthodes Fachgrundspezifikation - Allgemeine Anforderungen und
d'essai Prüfverfahren
(IEC 63138-1:2019) (IEC 63138-1:2019)
This European Standard was approved by CENELEC on 2019-10-17. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 63138-1:2019 E
---------------------- Page: 3 ----------------------
SIST EN IEC 63138-1:2020
EN IEC 63138-1:2019 (E)
European foreword
The text of document 46F/467/FDIS, future edition 1 of IEC 63138-1, prepared by SC 46F "RF and
microwave passive components" of IEC/TC 46 "Cables, wires, waveguides, RF connectors, RF and
microwave passive components and accessories" was submitted to the IEC-CENELEC parallel vote
and approved by CENELEC as EN IEC 63138-1:2019.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2020-07-17
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2022-10-17
document have to be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Endorsement notice
The text of the International Standard IEC 63138-1:2019 was approved by CENELEC as a European
Standard without any modification.
2
---------------------- Page: 4 ----------------------
SIST EN IEC 63138-1:2020
EN IEC 63138-1:2019 (E)
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 60068-1 - Environmental testing - Part 1: General EN 60068-1 -
and guidance
IEC 60068-2-6 - Environmental testing - Part 2-6: Tests - EN 60068-2-6 -
Test Fc: Vibration (sinusoidal)
IEC 60068-2-11 - Basic environmental testing procedures - EN 60068-2-11 -
Part 2-11: Tests - Test Ka: Salt mist
IEC 60068-2-20 - Environmental testing - Part 2-20: Tests - EN 60068-2-20 -
Test T: Test methods for solderability and
resistance to soldering heat of devices with
leads
IEC 60068-2-27 - Environmental testing - Part 2-27: Tests - EN 60068-2-27 -
Test Ea and guidance: Shock
IEC 61169-1 2013 Radio frequency connectors - Part 1: EN 61169-1 2013
Generic specification - General
requirements and measuring methods
IEC 61169-1-2 - Radio-frequency connectors - Part 1-2: - -
Electrical test methods - Insertion loss
1 2
IEC 61169-1-4 — Radio-frequency connectors - Part 1-4: EN 61169-1-4 —
Electrical test methods- voltage standing
wave ratio, return loss and reflection
coefficient
IEC 61726 - Cable assemblies, cables, connectors and EN 61726 -
passive microwave components -
Screening attenuation measurement by the
reverberation chamber method
1
Under preparation. Stage at time of preparation: IEC CDV 61169-1-4:2019.
2
Under preparation. Stage at time of preparation: prEN IEC 61169-1-4:2019.
3
---------------------- Page: 5 ----------------------
SIST EN IEC 63138-1:2020
EN IEC 63138-1:2019 (E)
Publication Year Title EN/HD Year
IEC 62037-3 - Passive RF and microwave devices, EN 62037-3 -
intermodulation level measurement - Part
3: Measurement of passive intermodulation
in coaxial connectors
4
---------------------- Page: 6 ----------------------
SIST EN IEC 63138-1:2020
IEC 63138-1
®
Edition 1.0 2019-09
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Multi-channel radio-frequency connectors –
Part 1: Generic specification – General requirements and test methods
Connecteurs radiofréquences multicanaux –
Partie 1: Spécification générique – Exigences générales et méthodes d'essai
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 33.120.30 ISBN 978-2-8322-7270-1
Warning! Make sure that you obtained this publication from an authorized distributor.
Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.
® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale
---------------------- Page: 7 ----------------------
SIST EN IEC 63138-1:2020
– 2 – IEC 63138-1:2019 © IEC 2019
CONTENTS
FOREWORD . 4
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 7
4 Design and construction . 7
4.1 General . 7
4.2 Materials and finishes . 8
4.3 Connector interface dimensions and gauge . 8
4.4 RF channel interface dimensions and gauge . 8
5 Standard ratings and characteristics . 8
6 Classifications into climatic categories . 8
7 IEC type designation . 8
8 Requirements and test methods . 9
8.1 General . 9
8.2 Visual inspection . 9
8.2.1 Requirements . 9
8.2.2 Inspection procedure . 10
8.3 Dimensions and interchangeability . 10
8.3.1 Interface dimensions for RF channels . 10
8.3.2 Interface dimensions for connectors . 10
8.3.3 Outline dimensions . 10
8.3.4 Mechanical compatibility . 10
8.4 Electrical tests . 11
8.4.1 Return loss (applicable for cabled connectors and adaptors) . 11
8.4.2 Insertion loss (applicable for cabled connectors and adaptors) . 11
8.4.3 Contact resistance . 11
8.4.4 Insulation resistance . 12
8.4.5 Voltage proof . 12
8.4.6 Screening effectiveness (applicable for cabled connectors and adaptors) . 13
8.4.7 Discharge test (applicable for cabled connectors and adaptors) . 13
8.4.8 Passive intermodulation level (PIM) . 14
8.4.9 Isolation (applicable for cabled connectors and adaptors) . 14
8.4.10 RF power rating (if necessary) . 15
8.5 Mechanical test . 17
8.5.1 Solderability (if applicable) . 17
8.5.2 Centre contact captivation (if applicable) . 17
8.5.3 RF channel captivation (if applicable) . 18
8.5.4 Engagement and disengagement forces . 18
8.5.5 Gauge retention force . 18
8.5.6 Effectiveness against cable rotation (if applicable) . 19
8.5.7 Effectiveness against cable pulling . 19
8.5.8 Effectiveness against cable bending . 20
8.5.9 Effectiveness against cable torsion (if applicable) . 20
8.5.10 Strength of coupling mechanism (if applicable) . 21
8.5.11 Low frequency vibration . 21
8.5.12 High frequency vibration . 22
---------------------- Page: 8 ----------------------
SIST EN IEC 63138-1:2020
IEC 63138-1:2019 © IEC 2019 – 3 –
8.5.13 Shock . 22
8.5.14 Mechanical endurance . 23
8.5.15 Safety wire hole pullout (if applicable) . 24
8.6 Environmental test . 24
8.6.1 Damp heat, steady state . 24
8.6.2 Thermal shock . 24
8.6.3 High temperature endurance. 24
8.6.4 Low temperature endurance . 24
8.6.5 Leakage (if applicable) . 24
8.6.6 Hermetic seal . 25
8.6.7 Salt mist . 25
9 Quality assessment . 25
9.1 General . 25
9.2 Qualification inspection . 25
9.2.1 Test samples . 25
9.2.2 Inspection procedure . 26
9.2.3 Structurally similar components . 27
9.3 Conformance inspection. 27
9.3.1 General . 27
9.3.2 Lot-by-lot inspection . 27
9.3.3 Periodic inspections . 28
9.4 Specification structures . 30
9.4.1 General . 30
9.4.2 Sectional specification (SS) . 30
9.4.3 Detail specification (DS) . 30
10 Marking . 30
10.1 Marking of components . 30
10.2 Marking and contents of package . 31
Figure 1 – Diagram for test for isolation . 15
Table 1 – Preferred climatic categories (see IEC 60068-1) . 8
Table 2 – Severities of vibration . 22
Table 3 – Recommended severities for shocks . 23
Table 4 – Qualification inspection . 26
Table 5 – Lot-by-lot inspection . 28
Table 6 – Sampling plans for mechanical compatibility and return loss inspection . 28
Table 7 – Periodic inspection . 29
---------------------- Page: 9 ----------------------
SIST EN IEC 63138-1:2020
– 4 – IEC 63138-1:2019 © IEC 2019
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
MULTI-CHANNEL RADIO-FREQUENCY CONNECTORS –
Part 1: Generic specification –
General requirements and test methods
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in
addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 63138-1 has been prepared by subcommittee 46F: RF and
microwave passive components, of IEC technical committee 46: Cables, wires, waveguides, RF
connectors, RF and microwave passive components and accessories.
The text of this International Standard is based on the following documents:
FDIS Report on voting
46F/467/FDIS 46F/481/RVD
Full information on the voting for the approval of this International Standard can be found in the
report on voting indicated in the above table.
This document has been drafted in accordance with the ISO/IEC Directives, Part 2.
---------------------- Page: 10 ----------------------
SIST EN IEC 63138-1:2020
IEC 63138-1:2019 © IEC 2019 – 5 –
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC website under "http://webstore.iec.ch" in the data related to
the specific document. At this date, the document will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
---------------------- Page: 11 ----------------------
SIST EN IEC 63138-1:2020
– 6 – IEC 63138-1:2019 © IEC 2019
MULTI-CHANNEL RADIO-FREQUENCY CONNECTORS –
Part 1: Generic specification –
General requirements and test methods
1 Scope
This part of IEC 63138-1, which is a generic specification, specifies general requirements for
multi-channel radio-frequency connectors, including terms and definitions, design and
construction, ratings and characteristics, climatic categories, IEC type designation,
requirements and test procedures, quality assessment, marking, etc.
It provides the basis for establishing the sectional specifications for various multi-channel
radio-frequency connector types.
This document applies to multi-channel radio-frequency connectors (called "connectors",
hereinafter) for use in communications, electronics and other equipment.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their
content constitutes requirements of this document. For dated references, only the edition cited
applies. For undated references, the latest edition of the referenced document (including any
amendments) applies.
IEC 60068-1, Environmental testing – Part 1: General and guidance
IEC 60068-2-6, Environmental testing – Part 2-6: Tests – Test Fc: Vibration (sinusoidal)
IEC 60068-2-11, Basic environmental testing procedures – Part 2-11: Tests – Test Ka: Salt mist
IEC 60068-2-20, Environmental testing – Part 2-20: Tests – Test T: Test methods for
solderability and resistance to soldering heat of devices with leads
IEC 60068-2-27, Environmental testing – Part 2-27: Tests – Test Ea and guidance: Shock
IEC 61169-1:2013, Radio frequency connectors – Part 1: Generic specification – General
requirements and measuring methods
IEC 61169-1-2, Radio-frequency connectors – Part 1-2: Electrical test methods – Insertion loss
1
, Radio-frequency connectors – Part 1-4: Electrical test methods – Voltage
IEC 61169-1-4:—
standing wave ratio, return loss and reflection coefficient
IEC 61726, Cable assemblies, cables, connectors and passive microwave components –
Screening attenuation measurement by the reverberation chamber method
IEC 62037-3, Passive RF and microwave devices, intermodulation level measurement – Part 3:
Measurement of passive intermodulation in coaxial connectors
___________
1
Under preparation. Stage at the time of publication: IEC CDV 61169-1-4:2019.
---------------------- Page: 12 ----------------------
SIST EN IEC 63138-1:2020
IEC 63138-1:2019 © IEC 2019 – 7 –
3 Terms and definitions
For the purposes of this document, the terms and definitions given in IEC 61169-1 and the
following apply.
ISO and IEC maintain terminological databases for use in standardization at the following
addresses:
• IEC Electropedia: available at http://www.electropedia.org/
• ISO Online browsing platform: available at http://www.iso.org/obp
3.1
RF channel
channel for RF transmission which is composed of an RF contact pair
3.2
multi-channel radio-frequency connector
connector with two or more RF channels
3.3
isolation
RF signal leakage generated from any one RF channel, with respect to any other RF channel
around it, and expressed by ratio of input power into the channel to the received power of any
other RF channel around it, in dB
It can be also expressed by Formula (1):
P
2
Isolation = −10log (1)
10
P
1
where
P is the input power into the RF channel, transmitted by signal source;
1
P is the received power of any other RF channel
2
4 Design and construction
4.1 General
The connectors and accessories shall be designed and constructed to meet the allowance
required for proper mating, installation and maintenance. The inserts in the connectors shall be
designed and constructed to ensure proper mating and performance of RF channels. When
design and construction permit, the connectors should have an indicator to show when mating
is in place. The RF contacts of connectors should be removable as far as possible.
A visual means shall be provided to indicate when two mating connectors are properly mated.
The relevant specification is not intended to restrict details of construction which do not affect
interchangeability or performance, or to be used as manufacturing drawings. The interface of
the connector accessories and the recommended opening hole dimensions of the panel shall
be as specified in the relevant specification.
The dimensions and tolerances shall be given in metric units. During conversion of dimensions
given in inches into millimetres, they shall be rounded to the nearest 0,001 mm or 0,000 05 in.
Where, however, mechanical and electrical considerations permit, the rounding shall usually be
to the nearest 0,01 mm or 0,000 5 in.
---------------------- Page: 13 ----------------------
SIST EN IEC 63138-1:2020
– 8 – IEC 63138-1:2019 © IEC 2019
4.2 Materials and finishes
The materials and finishes used for the connectors shall be as specified in the safety and
environmental regulations and in the relevant specifications. Dissimilar metals (between which
an electromotive coupling may exist) shall not be placed in contact with one another as an
electromotive force may be created between them.
4.3 Connector interface dimensions and gauge
The connector interface dimensions (including RF channel arrangements) and gauge shall
comply with the relevant specification.
4.4 RF channel interface dimensions and gauge
The interface dimensions and gauge for the RF channels in connectors shall comply with the
relevant specification.
5 Standard ratings and characteristics
The ratings and characteristics applicable to each connector type and style shall be specified in
the relevant specification. They should normally cover:
– electrical, mechanical and environmental performances;
– performances for each type of RF channel, which should be specified respectively when the
connector is composed of different types of RF channel.
6 Classifications into climatic categories
The classification of connectors with regard to climatic conditions is based on IEC 60068-1 and
indicated by a series of three sets of digits separated by oblique strokes corresponding
respectively to tests at low temperature (minus sign not shown), high temperature and the
number of days of exposure to damp heat, steady state.
The climatic severities are referenced by a cold temperature, high temperature and damp heat
steady state duration. Examples of preferred climatic categories of this are shown in Table 1.
Table 1 – Preferred climatic categories (see IEC 60068-1)
Category designation Letter Temperature range Damp heat steady state
40/85/21 A −40 °C to +85 °C 21 days
55/125/21 B −55 °C to +125 °C 21 days
55/155/56 C −55 °C to +155 °C 56 days
7 IEC type designation
The purpose of the IEC type designation is to identify a particular connector within the scope of
IEC RF connector standardization. It is not intended to include information in excess of this.
In practice, it is usually necessary to identify a manufacturer's product because, although it
may comply with this document, there may be features that are not covered by this document.
Connectors complying with the relevant specification shall be designated by the following
indications and in the order given:
a) the number of this document;
---------------------- Page: 14 ----------------------
SIST EN IEC 63138-1:2020
IEC 63138-1:2019 © IEC 2019 – 9 –
b) the letters "IEC";
c) series code (type designation);
d) additional identification as i
...
SLOVENSKI STANDARD
SIST EN IEC 63138-1:2020
01-januar-2020
Konektorji za večfrekvenčni radijski kanal - 1. del: Splošna specifikacija - Splošne
zahteve in merilne metode (IEC 63138-1:2019)
Multi-channel radio frequency connectors - Part 1: Generic specification - General
requirements and test methods (IEC 63138-1:2019)
Mehrkanalige Hochfrequenz-Steckverbinder - Teil 1: Fachgrundspezifikation -
Allgemeine Anforderungen und Prüfverfahren (IEC 63138-1:2019)
Connecteurs radiofréquences multicanaux - Partie 1: Spécification générique -
Exigences générales et méthodes d'essai (IEC 63138-1:2019)
Ta slovenski standard je istoveten z: EN IEC 63138-1:2019
ICS:
33.120.30 Radiofrekvenčni konektorji RF connectors
(RF)
SIST EN IEC 63138-1:2020 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN IEC 63138-1:2020
---------------------- Page: 2 ----------------------
SIST EN IEC 63138-1:2020
EUROPEAN STANDARD EN IEC 63138-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
November 2019
ICS 33.120.30
English Version
Multi-channel radio frequency connectors - Part 1: Generic
specification - General requirements and test methods
(IEC 63138-1:2019)
Connecteurs radiofréquences multicanaux - Partie 1: Mehrkanalige Hochfrequenz-Steckverbinder - Teil 1:
Spécification générique - Exigences générales et méthodes Fachgrundspezifikation - Allgemeine Anforderungen und
d'essai Prüfverfahren
(IEC 63138-1:2019) (IEC 63138-1:2019)
This European Standard was approved by CENELEC on 2019-10-17. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 63138-1:2019 E
---------------------- Page: 3 ----------------------
SIST EN IEC 63138-1:2020
EN IEC 63138-1:2019 (E)
European foreword
The text of document 46F/467/FDIS, future edition 1 of IEC 63138-1, prepared by SC 46F "RF and
microwave passive components" of IEC/TC 46 "Cables, wires, waveguides, RF connectors, RF and
microwave passive components and accessories" was submitted to the IEC-CENELEC parallel vote
and approved by CENELEC as EN IEC 63138-1:2019.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2020-07-17
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2022-10-17
document have to be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Endorsement notice
The text of the International Standard IEC 63138-1:2019 was approved by CENELEC as a European
Standard without any modification.
2
---------------------- Page: 4 ----------------------
SIST EN IEC 63138-1:2020
EN IEC 63138-1:2019 (E)
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 60068-1 - Environmental testing - Part 1: General EN 60068-1 -
and guidance
IEC 60068-2-6 - Environmental testing - Part 2-6: Tests - EN 60068-2-6 -
Test Fc: Vibration (sinusoidal)
IEC 60068-2-11 - Basic environmental testing procedures - EN 60068-2-11 -
Part 2-11: Tests - Test Ka: Salt mist
IEC 60068-2-20 - Environmental testing - Part 2-20: Tests - EN 60068-2-20 -
Test T: Test methods for solderability and
resistance to soldering heat of devices with
leads
IEC 60068-2-27 - Environmental testing - Part 2-27: Tests - EN 60068-2-27 -
Test Ea and guidance: Shock
IEC 61169-1 2013 Radio frequency connectors - Part 1: EN 61169-1 2013
Generic specification - General
requirements and measuring methods
IEC 61169-1-2 - Radio-frequency connectors - Part 1-2: - -
Electrical test methods - Insertion loss
1 2
IEC 61169-1-4 — Radio-frequency connectors - Part 1-4: EN 61169-1-4 —
Electrical test methods- voltage standing
wave ratio, return loss and reflection
coefficient
IEC 61726 - Cable assemblies, cables, connectors and EN 61726 -
passive microwave components -
Screening attenuation measurement by the
reverberation chamber method
1
Under preparation. Stage at time of preparation: IEC CDV 61169-1-4:2019.
2
Under preparation. Stage at time of preparation: prEN IEC 61169-1-4:2019.
3
---------------------- Page: 5 ----------------------
SIST EN IEC 63138-1:2020
EN IEC 63138-1:2019 (E)
Publication Year Title EN/HD Year
IEC 62037-3 - Passive RF and microwave devices, EN 62037-3 -
intermodulation level measurement - Part
3: Measurement of passive intermodulation
in coaxial connectors
4
---------------------- Page: 6 ----------------------
SIST EN IEC 63138-1:2020
IEC 63138-1
®
Edition 1.0 2019-09
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Multi-channel radio-frequency connectors –
Part 1: Generic specification – General requirements and test methods
Connecteurs radiofréquences multicanaux –
Partie 1: Spécification générique – Exigences générales et méthodes d'essai
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 33.120.30 ISBN 978-2-8322-7270-1
Warning! Make sure that you obtained this publication from an authorized distributor.
Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.
® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale
---------------------- Page: 7 ----------------------
SIST EN IEC 63138-1:2020
– 2 – IEC 63138-1:2019 © IEC 2019
CONTENTS
FOREWORD . 4
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 7
4 Design and construction . 7
4.1 General . 7
4.2 Materials and finishes . 8
4.3 Connector interface dimensions and gauge . 8
4.4 RF channel interface dimensions and gauge . 8
5 Standard ratings and characteristics . 8
6 Classifications into climatic categories . 8
7 IEC type designation . 8
8 Requirements and test methods . 9
8.1 General . 9
8.2 Visual inspection . 9
8.2.1 Requirements . 9
8.2.2 Inspection procedure . 10
8.3 Dimensions and interchangeability . 10
8.3.1 Interface dimensions for RF channels . 10
8.3.2 Interface dimensions for connectors . 10
8.3.3 Outline dimensions . 10
8.3.4 Mechanical compatibility . 10
8.4 Electrical tests . 11
8.4.1 Return loss (applicable for cabled connectors and adaptors) . 11
8.4.2 Insertion loss (applicable for cabled connectors and adaptors) . 11
8.4.3 Contact resistance . 11
8.4.4 Insulation resistance . 12
8.4.5 Voltage proof . 12
8.4.6 Screening effectiveness (applicable for cabled connectors and adaptors) . 13
8.4.7 Discharge test (applicable for cabled connectors and adaptors) . 13
8.4.8 Passive intermodulation level (PIM) . 14
8.4.9 Isolation (applicable for cabled connectors and adaptors) . 14
8.4.10 RF power rating (if necessary) . 15
8.5 Mechanical test . 17
8.5.1 Solderability (if applicable) . 17
8.5.2 Centre contact captivation (if applicable) . 17
8.5.3 RF channel captivation (if applicable) . 18
8.5.4 Engagement and disengagement forces . 18
8.5.5 Gauge retention force . 18
8.5.6 Effectiveness against cable rotation (if applicable) . 19
8.5.7 Effectiveness against cable pulling . 19
8.5.8 Effectiveness against cable bending . 20
8.5.9 Effectiveness against cable torsion (if applicable) . 20
8.5.10 Strength of coupling mechanism (if applicable) . 21
8.5.11 Low frequency vibration . 21
8.5.12 High frequency vibration . 22
---------------------- Page: 8 ----------------------
SIST EN IEC 63138-1:2020
IEC 63138-1:2019 © IEC 2019 – 3 –
8.5.13 Shock . 22
8.5.14 Mechanical endurance . 23
8.5.15 Safety wire hole pullout (if applicable) . 24
8.6 Environmental test . 24
8.6.1 Damp heat, steady state . 24
8.6.2 Thermal shock . 24
8.6.3 High temperature endurance. 24
8.6.4 Low temperature endurance . 24
8.6.5 Leakage (if applicable) . 24
8.6.6 Hermetic seal . 25
8.6.7 Salt mist . 25
9 Quality assessment . 25
9.1 General . 25
9.2 Qualification inspection . 25
9.2.1 Test samples . 25
9.2.2 Inspection procedure . 26
9.2.3 Structurally similar components . 27
9.3 Conformance inspection. 27
9.3.1 General . 27
9.3.2 Lot-by-lot inspection . 27
9.3.3 Periodic inspections . 28
9.4 Specification structures . 30
9.4.1 General . 30
9.4.2 Sectional specification (SS) . 30
9.4.3 Detail specification (DS) . 30
10 Marking . 30
10.1 Marking of components . 30
10.2 Marking and contents of package . 31
Figure 1 – Diagram for test for isolation . 15
Table 1 – Preferred climatic categories (see IEC 60068-1) . 8
Table 2 – Severities of vibration . 22
Table 3 – Recommended severities for shocks . 23
Table 4 – Qualification inspection . 26
Table 5 – Lot-by-lot inspection . 28
Table 6 – Sampling plans for mechanical compatibility and return loss inspection . 28
Table 7 – Periodic inspection . 29
---------------------- Page: 9 ----------------------
SIST EN IEC 63138-1:2020
– 4 – IEC 63138-1:2019 © IEC 2019
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
MULTI-CHANNEL RADIO-FREQUENCY CONNECTORS –
Part 1: Generic specification –
General requirements and test methods
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in
addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 63138-1 has been prepared by subcommittee 46F: RF and
microwave passive components, of IEC technical committee 46: Cables, wires, waveguides, RF
connectors, RF and microwave passive components and accessories.
The text of this International Standard is based on the following documents:
FDIS Report on voting
46F/467/FDIS 46F/481/RVD
Full information on the voting for the approval of this International Standard can be found in the
report on voting indicated in the above table.
This document has been drafted in accordance with the ISO/IEC Directives, Part 2.
---------------------- Page: 10 ----------------------
SIST EN IEC 63138-1:2020
IEC 63138-1:2019 © IEC 2019 – 5 –
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC website under "http://webstore.iec.ch" in the data related to
the specific document. At this date, the document will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
---------------------- Page: 11 ----------------------
SIST EN IEC 63138-1:2020
– 6 – IEC 63138-1:2019 © IEC 2019
MULTI-CHANNEL RADIO-FREQUENCY CONNECTORS –
Part 1: Generic specification –
General requirements and test methods
1 Scope
This part of IEC 63138-1, which is a generic specification, specifies general requirements for
multi-channel radio-frequency connectors, including terms and definitions, design and
construction, ratings and characteristics, climatic categories, IEC type designation,
requirements and test procedures, quality assessment, marking, etc.
It provides the basis for establishing the sectional specifications for various multi-channel
radio-frequency connector types.
This document applies to multi-channel radio-frequency connectors (called "connectors",
hereinafter) for use in communications, electronics and other equipment.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their
content constitutes requirements of this document. For dated references, only the edition cited
applies. For undated references, the latest edition of the referenced document (including any
amendments) applies.
IEC 60068-1, Environmental testing – Part 1: General and guidance
IEC 60068-2-6, Environmental testing – Part 2-6: Tests – Test Fc: Vibration (sinusoidal)
IEC 60068-2-11, Basic environmental testing procedures – Part 2-11: Tests – Test Ka: Salt mist
IEC 60068-2-20, Environmental testing – Part 2-20: Tests – Test T: Test methods for
solderability and resistance to soldering heat of devices with leads
IEC 60068-2-27, Environmental testing – Part 2-27: Tests – Test Ea and guidance: Shock
IEC 61169-1:2013, Radio frequency connectors – Part 1: Generic specification – General
requirements and measuring methods
IEC 61169-1-2, Radio-frequency connectors – Part 1-2: Electrical test methods – Insertion loss
1
, Radio-frequency connectors – Part 1-4: Electrical test methods – Voltage
IEC 61169-1-4:—
standing wave ratio, return loss and reflection coefficient
IEC 61726, Cable assemblies, cables, connectors and passive microwave components –
Screening attenuation measurement by the reverberation chamber method
IEC 62037-3, Passive RF and microwave devices, intermodulation level measurement – Part 3:
Measurement of passive intermodulation in coaxial connectors
___________
1
Under preparation. Stage at the time of publication: IEC CDV 61169-1-4:2019.
---------------------- Page: 12 ----------------------
SIST EN IEC 63138-1:2020
IEC 63138-1:2019 © IEC 2019 – 7 –
3 Terms and definitions
For the purposes of this document, the terms and definitions given in IEC 61169-1 and the
following apply.
ISO and IEC maintain terminological databases for use in standardization at the following
addresses:
• IEC Electropedia: available at http://www.electropedia.org/
• ISO Online browsing platform: available at http://www.iso.org/obp
3.1
RF channel
channel for RF transmission which is composed of an RF contact pair
3.2
multi-channel radio-frequency connector
connector with two or more RF channels
3.3
isolation
RF signal leakage generated from any one RF channel, with respect to any other RF channel
around it, and expressed by ratio of input power into the channel to the received power of any
other RF channel around it, in dB
It can be also expressed by Formula (1):
P
2
Isolation = −10log (1)
10
P
1
where
P is the input power into the RF channel, transmitted by signal source;
1
P is the received power of any other RF channel
2
4 Design and construction
4.1 General
The connectors and accessories shall be designed and constructed to meet the allowance
required for proper mating, installation and maintenance. The inserts in the connectors shall be
designed and constructed to ensure proper mating and performance of RF channels. When
design and construction permit, the connectors should have an indicator to show when mating
is in place. The RF contacts of connectors should be removable as far as possible.
A visual means shall be provided to indicate when two mating connectors are properly mated.
The relevant specification is not intended to restrict details of construction which do not affect
interchangeability or performance, or to be used as manufacturing drawings. The interface of
the connector accessories and the recommended opening hole dimensions of the panel shall
be as specified in the relevant specification.
The dimensions and tolerances shall be given in metric units. During conversion of dimensions
given in inches into millimetres, they shall be rounded to the nearest 0,001 mm or 0,000 05 in.
Where, however, mechanical and electrical considerations permit, the rounding shall usually be
to the nearest 0,01 mm or 0,000 5 in.
---------------------- Page: 13 ----------------------
SIST EN IEC 63138-1:2020
– 8 – IEC 63138-1:2019 © IEC 2019
4.2 Materials and finishes
The materials and finishes used for the connectors shall be as specified in the safety and
environmental regulations and in the relevant specifications. Dissimilar metals (between which
an electromotive coupling may exist) shall not be placed in contact with one another as an
electromotive force may be created between them.
4.3 Connector interface dimensions and gauge
The connector interface dimensions (including RF channel arrangements) and gauge shall
comply with the relevant specification.
4.4 RF channel interface dimensions and gauge
The interface dimensions and gauge for the RF channels in connectors shall comply with the
relevant specification.
5 Standard ratings and characteristics
The ratings and characteristics applicable to each connector type and style shall be specified in
the relevant specification. They should normally cover:
– electrical, mechanical and environmental performances;
– performances for each type of RF channel, which should be specified respectively when the
connector is composed of different types of RF channel.
6 Classifications into climatic categories
The classification of connectors with regard to climatic conditions is based on IEC 60068-1 and
indicated by a series of three sets of digits separated by oblique strokes corresponding
respectively to tests at low temperature (minus sign not shown), high temperature and the
number of days of exposure to damp heat, steady state.
The climatic severities are referenced by a cold temperature, high temperature and damp heat
steady state duration. Examples of preferred climatic categories of this are shown in Table 1.
Table 1 – Preferred climatic categories (see IEC 60068-1)
Category designation Letter Temperature range Damp heat steady state
40/85/21 A −40 °C to +85 °C 21 days
55/125/21 B −55 °C to +125 °C 21 days
55/155/56 C −55 °C to +155 °C 56 days
7 IEC type designation
The purpose of the IEC type designation is to identify a particular connector within the scope of
IEC RF connector standardization. It is not intended to include information in excess of this.
In practice, it is usually necessary to identify a manufacturer's product because, although it
may comply with this document, there may be features that are not covered by this document.
Connectors complying with the relevant specification shall be designated by the following
indications and in the order given:
a) the number of this document;
---------------------- Page: 14 ----------------------
SIST EN IEC 63138-1:2020
IEC 63138-1:2019 © IEC 2019 – 9 –
b) the letters "IEC";
c) series code (type designation);
d) additional identification
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.