SIST EN ISO 11252:2008
(Main)Lasers and laser-related equipment - Laser device - Minimum requirements for documentation (ISO 11252:2004)
Lasers and laser-related equipment - Laser device - Minimum requirements for documentation (ISO 11252:2004)
This International Standard specifies the minimum documentation and information for marking and labelling, to be provided with laser devices (including laser diodes). The documentation is presented on two levels: as a technical data sheet (Clause 5 ) and as an instruction manual (Clause 6). This International Standard does not apply to laser products which incorporate la ser devices. It also does not apply to laser devices manufactu red before the date of publication of this document.Requirements on noise are not included in this standard. These requirem ents will be included in a subsequent amendment.
Laser und Laseranlagen - Lasergerät - Mindestanforderungen an die Dokumentation (ISO 11252:2004)
Diese Internationale Norm legt die Mindestanforderungen für die Dokumentation, Kennzeichnung und
Beschilderung fest, die Lasergeräten (einschließlich Laserdioden) beigefügt werden müssen.
Die Dokumentation wird in zwei Bereiche gegliedert: in das technische Datenblatt (Abschnitt 5) und in die
Betriebsanleitung (Abschnitt 6).
Diese Internationale Norm gilt nicht für Laseranlagen, die Lasergeräte enthalten.
Sie gilt auch nicht für Lasergeräte, die vor der Veröffentlichung dieser Norm hergestellt wurden.
Anforderungen an Lärmschutz sind nicht enthalten. Diese Anforderungen sollen in einer späteren Änderung
eingeführt werden.
Lasers et équipements associés aux lasers - Source laser - Exigences minimales pour la documentation (ISO 11252:2004)
L'ISO 11252:2004 spécifie la documentation minimale et les informations sur le marquage et l'étiquetage qui doivent être fournies avec une source laser (y compris les diodes lasers).
La documentation est présentée en deux niveaux: comme une fiche technique et comme un manuel d'instructions.
L'ISO 11252:2004 ne s'applique pas aux produits lasers qui contiennent des sources laser.
L'ISO 11252:2004 ne s'applique pas non plus aux sources lasers fabriquées avant la date de publication de ce document.
Les exigences sur le bruit ne sont pas incluses dans cette norme. Elles seront incluses dans un amendement à venir.
Laserji in laserska oprema - Laserska naprava - Minimalne zahteve za dokumentacijo (ISO 11252:2004)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 11252:2008
01-november-2008
1DGRPHãþD
SIST EN ISO 11252:2005
Laserji in laserska oprema - Laserska naprava - Minimalne zahteve za
dokumentacijo (ISO 11252:2004)
Lasers and laser-related equipment - Laser device - Minimum requirements for
documentation (ISO 11252:2004)
Laser und Laseranlagen - Lasergerät - Mindestanforderungen an die Dokumentation
(ISO 11252:2004)
Lasers et équipements associés aux lasers - Source laser - Exigences minimales pour la
documentation (ISO 11252:2004)
Ta slovenski standard je istoveten z: EN ISO 11252:2008
ICS:
31.260 Optoelektronika, laserska Optoelectronics. Laser
oprema equipment
SIST EN ISO 11252:2008 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 11252:2008
---------------------- Page: 2 ----------------------
SIST EN ISO 11252:2008
EUROPEAN STANDARD
EN ISO 11252
NORME EUROPÉENNE
EUROPÄISCHE NORM
July 2008
ICS 31.260 Supersedes EN ISO 11252:2004
English Version
Lasers and laser-related equipment - Laser device - Minimum
requirements for documentation (ISO 11252:2004)
Lasers et équipements associés aux lasers - Source laser - Laser und Laseranlagen - Lasergerät -
Exigences minimales pour la documentation (ISO Mindestanforderungen an die Dokumentation (ISO
11252:2004) 11252:2004)
This European Standard was approved by CEN on 22 June 2008.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2008 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 11252:2008: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 11252:2008
EN ISO 11252:2008 (E)
Contents Page
Foreword.3
Annex ZA ((informative) Relationship between this European Standard and the Essential
Requirements of EU Directive 98/37/EC .4
Annex ZB (informative) Relationship between this European Standard and the Essential
Requirements of EU Directive 2006/42/EC .5
2
---------------------- Page: 4 ----------------------
SIST EN ISO 11252:2008
EN ISO 11252:2008 (E)
Foreword
The text of ISO 11252:2004 has been prepared by Technical Committee ISO/TC 172 “Optics and optical
instruments” of the International Organization for Standardization (ISO) and has been taken over as EN ISO
11252:2008 by Technical Committee CEN/TC 123 “Lasers and photonics” the secretariat of which is held by
DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by January 2009, and conflicting national standards shall be withdrawn at
the latest by January 2009.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 11252:2004.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EC Directive(s).
For relationship with EC Directives, see informative Annexes ZA and ZB, which are integral part of this
document.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 11252:2004 has been approved by CEN as a EN ISO 11252:2008 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 11252:2008
EN ISO 11252:2008 (E)
Annex ZA
((informative)
Relationship between this European Standard and the Essential Requirements of EU
Directive 98/37/EC
This European Standard has been prepared under a mandate given to CEN by the European Commission
and the European Free Trade Association to provide one means of conforming to Essential Requirements of
the New Approach Directive 98/37/EC.
Once this standard is cited in the Official Journal of the European Communities under that Directive and has
been implemented as a national standard in at least one Member State, compliance with the normative
clauses of this standard confers, within the limits of the scope of this standard, a presumption of conformity
with the relevant Essential Requirements of that Directive and associated EFTA regulations.
WARNING: Other requirements and other EU Directives may be applicable to the products falling within the
scope of this International standard.
4
---------------------- Page: 6 ----------------------
SIST EN ISO 11252:2008
EN ISO 11252:2008 (E)
Annex ZB
(informative)
Relationship between this European Standard and the Essential Requirements of
EU Directive 2006/42/EC
This European Standard has been prepared under a mandate given to CEN by the European Commission
and the European Free Trade Association to provide a means of conforming to Essential Requirements of the
New Approach Directive 2006/42/EC on machinery.
Once this standard is cited in the Official Journal of the European Communities under that Directive and has
been implemented as a national standard in at least one Member State, compliance with the normative
clauses of this standard confers, within the limits of the scope of this standard, a presumption of conformity
with the relevant Essential Requirements of that Directive and associated EFTA regulations.
WARNING — Other requirements and other EU Directives may be applicable to the product(s) falling within
the scope of this standard.
5
---------------------- Page: 7 ----------------------
SIST EN ISO 11252:2008
---------------------- Page: 8 ----------------------
SIST EN ISO 11252:2008
INTERNATIONAL ISO
STANDARD 11252
Second edition
2004-11-15
Lasers and laser-related equipment —
Laser device — Minimum requirements
for documentation
Lasers et équipements associés aux lasers — Source laser —
Exigences minimales pour la documentation
Reference number
ISO 11252:2004(E)
©
ISO 2004
---------------------- Page: 9 ----------------------
SIST EN ISO 11252:2008
ISO 11252:2004(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2004
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2004 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 11252:2008
ISO 11252:2004(E)
Contents Page
Foreword. iv
Introduction . v
1 Scope. 1
2 Normative references . 1
3 Terms and definitions. 2
4 Units . 2
5 Technical data sheet. 2
5.1 General. 2
5.2 Beam output characteristics. 2
5.3 Power supply. 2
5.4 Liquids and gases. 3
5.5 Environmental conditions. 3
5.6 Mechanical interfaces. 4
5.7 Safety. 4
6 Instruction manual . 4
7 Marking and labelling . 4
Annex A (informative) Model of data sheet. 5
Bibliography . 9
© ISO 2004 – All rights reserved iii
---------------------- Page: 11 ----------------------
SIST EN ISO 11252:2008
ISO 11252:2004(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 11252 was prepared by Technical Committee ISO/TC 172, Optics and photonics, Subcommittee SC 9,
Electro-optical systems.
This second edition cancels and replaces the first edition (ISO 11252:1993), which has been technically
revised.
iv © ISO 2004 – All rights reserved
---------------------- Page: 12 ----------------------
SIST EN ISO 11252:2008
ISO 11252:2004(E)
Introduction
This document is a type B1 standard as defined in ISO 12100-1.
The provisions of this document may be supplemented or modified by a type C standard.
NOTE For machines which are covered by the scope of a type C standard and which have been designed and built
according to the provisions of that standard, the provisions of that type C standard take precede
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.