SIST EN 13249:2001/A1:2005
(Amendment)Geotextiles and geotextile-related products - Required characteristics for use in the construction of roads and other trafficked areas
Geotextiles and geotextile-related products - Required characteristics for use in the construction of roads and other trafficked areas
This European Standard specifies the relevant characteristics of geotextiles and geotextile-related products used in the construction of roads and other trafficked areas (excluding railways and asphaltic inclusion), and the appropriate test methods to determine these characteristics. The intended use of these geotextiles or geotextile-related products is to fulfil one or more of the following functions: filtration, separation and reinforcement. The separation function is always used in conjunction with filtration or reinforcement, accordingly separation will never be specified alone. This standard is not applicable to geomembranes. This standard provides for the evaluation of conformity of the product to this European Standard and for factory production control procedures. This standard defines requirements to be met by manufacturers and distributors with regard to the presentation of product properties.
Geotextilien und geotextilverwandte Produkte - Geforderte Eigenschaften für die Anwendung beim Bau von Straßen und sonstigen Verkehrsflächen
Géotextiles et produits apparentés - Caractéristiques requises pour l'utilisation dans la construction des routes et autres zones de circulation
Geotekstilije in geotekstilijam sorodni izdelki - Zahtevane lastnosti za uporabo pri gradnji cest in drugih prometnih površin
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 13249:2001/A1:2005
01-maj-2005
Geotekstilije in geotekstilijam sorodni izdelki - Zahtevane lastnosti za uporabo pri
gradnji cest in drugih prometnih površin
Geotextiles and geotextile-related products - Required characteristics for use in the
construction of roads and other trafficked areas
Geotextilien und geotextilverwandte Produkte - Geforderte Eigenschaften für die
Anwendung beim Bau von Straßen und sonstigen Verkehrsflächen
Géotextiles et produits apparentés - Caractéristiques requises pour l'utilisation dans la
construction des routes et autres zones de circulation
Ta slovenski standard je istoveten z: EN 13249:2000/A1:2005
ICS:
59.080.70 Geotekstilije Geotextiles
93.080.20 Materiali za gradnjo cest Road construction materials
SIST EN 13249:2001/A1:2005 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 13249:2001/A1:2005
---------------------- Page: 2 ----------------------
SIST EN 13249:2001/A1:2005
EUROPEAN STANDARD
EN 13249:2000/A1
NORME EUROPÉENNE
EUROPÄISCHE NORM
January 2005
ICS 59.080.70
English version
Geotextiles and geotextile-related products - Required
characteristics for use in the construction of roads and other
trafficked areas
Géotextiles et produits apparentés - Caractéristiques Geotextilien und geotextilverwandte Produkte - Geforderte
requises pour l'utilisation dans la construction des routes et Eigenschaften für die Anwendung beim Bau von Straßen
autres zones de circulation und sonstigen Verkehrsflächen
This amendment A1 modifies the European Standard EN 13249:2000; it was approved by CEN on 15 December 2004.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this
amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references concerning such
national standards may be obtained on application to the Central Secretariat or to any CEN member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2005 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13249:2000/A1:2005: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 13249:2001/A1:2005
EN 13249:2000/A1:2005 (E)
Foreword
This document (EN 13249:2000/A1:2005) has been prepared by Technical Committee CEN/TC 189
"Geosynthetics", the secretariat of which is held by IBN.
This Amendment to the European Standard EN 13249:2000 shall be given the status of a national
standard, either by publication of an identical text or by endorsement, at the latest by July 2005, and
conflicting national standards shall be withdrawn at the latest by July 2005.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia,
Spain, Sweden, Switzerland and United Kingdom.
2
---------------------- Page: 4 ----------------------
SIST EN 13249:2001/A1:2005
EN 13249:2000/A1:2005 (E)
1 Modification to Clause 2
include reference to:
"ISO 10390:1994 – Soil quality – Determination of pH"
2 Modification to 5.2, Note 1
replace by:
"This method should not be used for on-site quality control purposes. On-site control procedures are
described in CEN/TR 15019.”
3 Modification to 5.4
th
add at the end of the 4 paragraph:
"The tasks of the manufacturer shall be described in detail including the type of tests to be performed
and the frequency of these tests (see also Annex A, Clause A.2)."
4 Modification to 5.5
replace by:
"Inspection of the factory and of the factory production control shall be made not less than once a
year, given constant production conditions, on the provisions contained in Clause 5.4 and Annex A.
The inspection shall include an initial inspection of the factory and a continuous surveillance,
assessment and approval of the factory production control, where required. The single steps of this
inspection are specified in Annex A, Clause A.2."
6 Modification to Annex A
- Rename Annex A (normative) as: Factory Production Control
- Renumber and rename the current and its subclauses:
Annex A becomes A.1 Scheme of factory production control, A1 becomes A1.1, A2 becomes A1.2
etc.
- A.1.1.1 and A.1.1.2
Replace "design" by " product design"
- The introductory text shall read as:
"The items to be addressed in the factory production control manual relating to the system of control,
determined from Clause 5.4, are given in Clause A.1. The single steps of factory production control
are addressed in the checklist (A.2).
- Replace NOTE by:
NOTE Manufacturers operating a quality system conforming to EN ISO 9001:2000 are presumed to
meet requirements of this Annex A.
After A.1.4.6, insert new Clause A.2: text see below
A.2 Checklist for the assessment of a factory production control (FPC)
system.
NOTE This checklist has been developed for CE marking, but may also be used for the purpose of
voluntary certification systems.
A.2.1 General
A factory production control system can only be applicable to one production site. In case of several
production lines at the same site, all of them shall be checked.
The results of audits performed by a quality management system certification body (e.g. for ISO
9001:2000 certification) can be taken into account, although such certificate is not compulsory.
3
---------------------- Page: 5 ----------------------
SIST EN 13249:2001/A1:2005
EN 13249:2000/A1:2005 (E)
The FPC shall cover specified product ranges produced on the same production site. Each product
covered by the FPC shall be clearly identified. To add a new product to the covered range, the
producer shall submit the results of the initial type testing of the new product for an extension of the
FPC system. This shall be taken into account at the next follow-up inspection. In case of a new
production process the manufacturer shall apply for a new inspection visit.
Follow-up inspections shall take place not less than once a year.
All the questions in this checklist shall be checked at the first inspection visit and at each follow-up
inspection.
A.2.2 Checklist
The items marked with "E" are considered to be of essential importance, i.e. immediate corrective
actions are needed if the requirement is not fulfilled.
The assessment can lead to A-, B- or C-type remarks:
A: an immediate corrective action is needed;
B: corrective action shall be taken within 3 months;
C: corrective action shall be taken before the next inspection visit.
If a B-type remark is not corrected in due time, it becomes an "A" and if a C-type remark is not
corrected in due time, it becomes a "B".
Question Relevance Comment
1 Design
1.1 - Has the manufacturer a description how To be assessed only if
claimed by the manufacturer.
design requirements and criteria are identified,
checked, controlled and updated to be Refer to the manufacturer's
documentation.
unambiguous and relevant to the use of the
product and its specification?
1.2 - Has the manufacturer a description of the To be assessed only if
claimed by the manufacturer.
communication of the design to the internal
production departments or to external Refer to the manufacturer's
documentation.
subcontractors?
2 Product identification and traceability
Refer to the manufacturer's
2.1 -What are the means used for the unique E
identification of any individual finished product? documentation.
2.2 - Is it possible to identify and check date, E Refer to the manufacturer's
documentation.
place and general manufacturing conditions
(including raw material used) through the
identifications on the final product?
2.3 -Does the marking on the final product E
comply with EN ISO 10320?
3 Production process control
3.1 -Are there documents which define the E Refer to the manufacturer's
documentation.
production process parameters which could
affect quality?
3.2 -Are the standards and procedures E
i
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.