Safety of machinery - Safety requirements for the design and construction of paper making and finishing machines - Part 7: Chests

This document applies to chests used in paper making and shall be applied together with EN 1034-1:2000. It
deals with all significant hazards, hazardous situations and hazard events relevant to chests when they are
used as intended and under the conditions foreseen by the manufacturer (see clause 4). This standard does
not apply to tanks for chemicals, storage tanks for starch and other additives used in paper making or basins
or vessels for waste water resulting from the paper making process.
This document does not apply to chests manufactured before the publication date of this document.

Sicherheit von Maschinen - Sicherheitstechnische Anforderungen an Konstruktion und Bau von Maschinen der Papierherstellung und Ausrüstung - Teil 7: Bütten

Diese Europäische Norm gilt für Bütten, die zur Verwendung bei der Papierherstellung bestimmt sind, und ist
gemeinsam mit EN 1034-1:2000 anzuwenden. Sie behandelt alle signifikanten Gefährdungen,
Gefährdungssituationen und Gefährdungsereignisse, die auf Bütten zutreffen, wenn sie bestimmungsgemäß und
entsprechend den vorhersehbaren Bedingungen des Herstellers verwendet werden (siehe Abschnitt 4). Diese
Europäische Norm gilt nicht für Behälter für Chemikalien, Silos für Stärke und andere Zuschlagstoffe, die bei der
Papierherstellung verwendet werden, und Becken oder Behälter für Abwasser, das bei der Papierherstellung
anfällt.
Diese Europäische Norm gilt nicht für Bütten, die hergestellt wurden, bevor CEN diese Europäische Norm
veröffentlichte.

Sécurité des machines - Prescriptions de sécurité pour la conception et la construction de machines de fabrication et de finition du papier - Partie 7 : Cuviers

La présente Norme européenne s'applique aux cuviers, qui sont destinés a etre employés dans la fabrication
du papier, et doit etre utilisée conjointement avec l'EN 1034-1:2000. Elle traite tous les phénomenes
dangereux significatifs, les situations dangereuses et les évenements dangereux qui s'appliquent aux cuviers
lorsqu'ils sont utilisés dans des conditions normales et conformément aux conditions prévisibles du fabricant
(voir article 4). La présente norme européenne ne s'applique ni aux réservoirs de produits chimiques, silos
pour l?amidon et autres matieres d?apport utilisés dans la fabrication du papier, ni aux bassins ou réservoirs
d?eaux usées résultant de la fabrication du papier.
La présente Norme européenne ne s'applique pas aux cuviers qui ont été fabriqués avant sa publication par
le CEN.

Varnost strojev – Varnostne zahteve za načrtovanje in konstrukcijo strojev in opreme za izdelavo papirja – 7. del: Kadi

General Information

Status
Withdrawn
Publication Date
31-Oct-2005
Withdrawal Date
22-Dec-2009
Technical Committee
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
18-Dec-2009
Due Date
10-Jan-2010
Completion Date
23-Dec-2009

RELATIONS

Buy Standard

Standard
SIST EN 1034-7:2005
English language
11 pages
sale 10% off
Preview
sale 10% off
Preview

e-Library read for
1 day

Standards Content (sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Sicherheit von Maschinen - Sicherheitstechnische Anforderungen an Konstruktion und Bau von Maschinen der Papierherstellung und Ausrüstung - Teil 7: BüttenSécurité des machines - Prescriptions de sécurité pour la conception et la construction de machines de fabrication et de finition du papier - Partie 7 : CuviersSafety of machinery - Safety requirements for the design and construction of paper making and finishing machines - Part 7: Chests85.100Oprema za papirno industrijoEquipment for the paper industry21.020Characteristics and design of machines, apparatus, equipment13.110Varnost strojevSafety of machineryICS:Ta slovenski standard je istoveten z:EN 1034-7:2005SIST EN 1034-7:2005en01-november-2005SIST EN 1034-7:2005SLOVENSKI

STANDARD
SIST EN 1034-7:2005

EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 1034-7June 2005ICS 85.100English versionSafety of machinery - Safety requirements for the design andconstruction of paper making and finishing machines - Part 7:ChestsSécurité des machines - Prescriptions de sécurité pour laconception et la construction de machines de fabrication etde finition du papier - Partie 7 : CuviersSicherheit von Maschinen - SicherheitstechnischeAnforderungen an Konstruktion und Bau von Maschinender Papierherstellung und Ausrüstung - Teil 7: BüttenThis European Standard was approved by CEN on 21 April 2005.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36

B-1050 Brussels© 2005 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 1034-7:2005: ESIST EN 1034-7:2005

EN 1034-7:2005 (E) 2 Contents Page Foreword.......................................................................................................................................................3 Introduction...................................................................................................................................................4 1 Scope................................................................................................................................................4 2 Normative references.......................................................................................................................4 3 Terms and definitions......................................................................................................................5 4 List of significant hazards................................................................................................................5 5 Safety requirements and/or measures............................................................................................7 5.1 General..............................................................................................................................................7 5.2 Power transmission elements.........................................................................................................7 5.3 Working platforms and means of access........................................................................................7 5.4 Inspection holes...............................................................................................................................7 5.5 Electrical equipment.........................................................................................................................7 5.6 Hydraulic and pneumatic equipment...............................................................................................7 5.7 Level control devices.......................................................................................................................7 5.8 Lighting.............................................................................................................................................8 5.9 Noise.................................................................................................................................................8 5.10 Equipment and measures for maintenance and cleaning..............................................................8 5.11 Powered gate valves........................................................................................................................8 5.12 Emergency stop devices and emergency measures......................................................................9 5.13 Explosion protection........................................................................................................................9 6 Verification of safety requirements and/or measures.....................................................................9 7 Information for use...........................................................................................................................9 Annex ZA (informative)

Relationship between this European

Standard and the Essential Requirements of EU Directive 98/37/EC........................................................................................11

SIST EN 1034-7:2005

EN 1034-7:2005 (E) 3 Foreword This European Standard (EN 1034-7:2005) has been prepared by Technical Committee CEN/TC 198 “Printing and paper machinery - Safety”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by December 2005, and conflicting national standards shall be withdrawn at the latest by December 2005 This European Standard has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of the EU Directive For relationship with the EU Directive, see informative annex ZA, which is an integral part of this European Standard. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. . SIST EN 1034-7:2005

EN 1034-7:2005 (E) 4 Introduction This European Standard is a C type standard as stated in EN ISO 12100-1.

The extent to which hazards, hazardous situations and hazard results are covered is indicated in the scope of this standard. For machines which have been designed and built in accordance with the stipulations of this C type standard, the following applies: where C type standard stipulations deviate from respective stipulations in A or B type standards, the stipulations made in this C type standard take precedence over stipulations in the other standards. 1 Scope This European Standard applies to chests used in paper making and shall be applied together with EN 1034-1:2000. It deals with all significant hazards, hazardous situations and hazard events relevant to chests when they are used as intended and under the conditions foreseen by the manufacturer (see clause 4). This European Standard does not apply to tanks for chemicals, storage tanks for starch and other additives used in paper making or basins or vessels for waste water resulting from the paper making process. This European Standard does not apply to chests manufactured before the publication date of this European Standard. 2 Normative references The following referenced documents are indispensable for the application of this European Standard.

For dated references, only the edition cited applies.

For undated references, the latest edition of the referenced document (including any amendments) applies. EN 294:1992, Safety of machinery — Safety distances to prevent danger zones being reached by the upper limbs EN 349:1993, Safety of machinery — Minimum gaps to avoid crushing of parts of the human body EN 418:1992, Safety of machinery — Emergency stop equipment — Functional aspects EN 547-2:1996, Safety of machinery — Human body measurement — Part 2: Principles for determining the dimensions required for access openings EN 953:1997, Safety of machinery — Guards — General requirements for the design and construction of fixed and movable guards EN 954-1:1996, Safety of machinery — Safety-related parts of control systems — Part 1: General principles for design EN 982:1996, Safety of machinery — Safety requirements for fluid power systems and components — Hydraulics EN 983:1996, Safety of machinery — Safety requirements for fluid power systems and components — Pneumatics SIST EN 1034-7:2005

EN 1034-7:2005 (E) 5 EN 1034-1:2000, Safety of machinery — Safety requirements for the design and construction of paper making and finishing machines — Part 1: Common requirements EN 1037:1995, Safety of machinery — Prevention of unexpected start-up EN 1050:1996, Safety of machinery — Principles for risk assessment EN 1127-1:1997, Explosive atmospheres — Explosion prevention and protection — Part 1: Basic concepts and methodology EN 13023:2003, Noise measurement methods for printing, paper converting, paper making machines and auxiliary equipment — Accuracy categories 2 and 3 EN 50144-1:1998, Safety of hand-held powered electrical devices — Part 1: General requirements EN 60204-1:1997, Safety of machinery — Electrical equipment of machines — Part 1: General requirements

(IEC 60204-1:1997) EN 60974-1:1988, Arc welding equipment - Part 1: Welding power sources (IEC 60974-1:1998)

EN 61000-6-2:2001, Electromagnetic compatibility (EMC) — Part 6-2: Generic standards; immunity for industrial environment (IEC 61000-6-2:1999, modified) EN ISO 12100-1:2003, Safety of machinery — Basic concepts, general principles for design — Part 1: Basic terminology, methodology (ISO 12100-1:2003) EN ISO 12100-2:2003, Safety of machinery — Basic concepts, general principles for design — Part 2: Technical principles

(ISO 12100-2:2003) EN ISO 14122:2001 (all parts), Safety of machinery — Permanent means of access to machinery 3 Terms and definitions For the purposes of this European Standard, the definitions given in EN 1034-1:2000, EN ISO 12100-1:2003, and the following definitions apply: 3.1

chest vessel usually made of special steel or concrete and equipped with a fixed agitating device, associated measuring and control devices and necessary shutoff devices intended for

...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.