SIST EN ISO 16852:2017
(Main)Flame arresters - Performance requirements, test methods and limits for use (ISO 16852:2016)
Flame arresters - Performance requirements, test methods and limits for use (ISO 16852:2016)
This International Standard specifies the requirements for flame arresters that prevent flame
transmission when explosive gas-air or vapour-air mixtures are present. It establishes uniform principles
for the classification, basic construction and information for use, including the marking of flame arresters,
and specifies test methods to verify the safety requirements and determine safe limits of use.
This International Standard is valid for pressures ranging from 80 kPa to 160 kPa and temperatures
ranging from −20 °C to + 150 °C.
NOTE 1 For flame arresters with operational conditions inside the scope, but outside atmospheric conditions,
see 7.4.
NOTE 2 In designing and testing flame arresters for operation under conditions other than those specified
above, this International Standard can be used as a guide. However, additional testing related specifically to the
intended conditions of use is advisable. This is particularly important when high temperatures and pressures are
applied. The test mixtures might need to be modified in these cases.
NOTE 3 An additional standard IMO MSC/Circ. 677 for maritime application from IMO (International Maritime
Organization) exists.
This International Standard is not applicable to the following:
— external safety-related measurement and control equipment that might be required to keep the
operational conditions within the established safe limits;
NOTE 4 Integrated measurement and control equipment, such as integrated temperature and flame sensors
as well as parts which, for example, intentionally melt (retaining pin), burn away (weather hoods) or bend
(bimetallic strips), is within the scope of this International Standard.
— flame arresters used for explosive mixtures of vapours and gases, which tend to self-decompose
(e.g. acetylene) or which are chemically unstable;
— flame arresters used for carbon disulphide, due to its special properties;
— flame arresters whose intended use is for mixtures other than gas-air or vapour-air mixtures (e.g.
higher oxygen-nitrogen ratio, chlorine as oxidant, etc.);
— flame arrester test procedures for internal-combustion compression ignition engines;
— fast acting valves, extinguishing systems and other explosion isolating systems.
Flammendurchschlagsicherungen - Leistungsanforderungen, Prüfverfahren und Einsatzgrenzen (ISO 16852:2016)
Diese Internationale Norm legt die Anforderungen an Flammendurchschlagsicherungen fest, die Flammendurchschläge bei Vorhandensein von explosionsfähigen Gas-Luft- oder Dampf-Luft-Gemischen verhindern. Sie stellt einheitliche Grundsätze für die Klassifizierung, die grundlegende Konstruktion und die Informationen für den Einsatz einschließlich der Kennzeichnung von Flammendurchschlagsicherungen auf und legt Prüfverfahren zur Überprüfung der sicherheitstechnischen Anforderungen und zur Bestimmung der sicheren Einsatzgrenzen fest.
Diese Internationale Norm gilt für Drücke von 80 kPa bis 160 kPa und für Temperaturen von −20 °C bis +150 °C.
ANMERKUNG 1 Für Flammendurchschlagsicherungen unter Betriebsbedingungen innerhalb des Anwendungsbereichs, aber außerhalb der atmosphärischen Bedingungen siehe 7.4.
ANMERKUNG 2 Diese Internationale Norm kann für Betriebsbedingungen, die von den oben festgelegten abweichen, als Leitlinie für die Auslegung und Prüfung von Flammendurchschlagsicherungen, dienen. Zusätzliche Prüfungen, insbesondere hinsichtlich der vorgesehenen Einsatzbedingungen, sind jedoch ratsam. Dies ist besonders bei hohen Temperaturen und Drücken wichtig. Die Prüfgemische müssen in diesen Fällen möglicherweise verändert werden.
ANMERKUNG 3 Es ist eine zusätzliche Norm IMO MSC/Circ. 677 für die Anwendung auf See von der IMO (Internationale Seeschifffahrts-Organisation) vorhanden.
Diese Internationale Norm gilt nicht für:
externe sicherheitsrelevante Mess- und Überwachungseinrichtungen, die erforderlich sind, um die Betriebsbedingungen innerhalb der festgelegten sicheren Grenzen zu halten;
ANMERKUNG 4 Eingebaute Mess- und Überwachungseinrichtungen, wie z. B. integrierte Temperatur- und Flammenmessfühler sowie Bauteile bei denen es beispielsweise beabsichtigt ist, dass sie schmelzen (Rückhaltestift), wegbrennen (Wetterhauben) oder sich verformen (Bimetallstreifen), fallen in den Anwendungsbereich dieser Internationalen Norm.
Flammendurchschlagsicherungen für explosionsfähige Gemische aus Dämpfen und Gasen, die zum Selbstzerfall neigen (z. B. Acetylen) oder die chemisch instabil sind;
Flammendurchschlagsicherungen, die bei Schwefelkohlenstoff eingesetzt werden, da dieser spezielle Eigenschaften besitzt;
Flammendurchschlagsicherungen, die bestimmungsgemäß für andere Gemische als Gas-Luft- oder Dampf Luft-Gemische (z. B. höheres Verhältnis Sauerstoff-Stickstoff, Chlor als Oxidationsmittel usw.) eingesetzt werden sollen;
Prüfverfahren für Flammendurchschlagsicherungen an Verbrennungsmotoren mit Kompressionszündung;
Schnellschlussventile, Löschsysteme und andere Explosionsentkoppelungssysteme.
Arrête-flammes - Exigences de performance, méthodes d'essai et limites d'utilisation (ISO 16852:2016)
ISO 16852:2016 internationale spécifie les exigences applicables aux arrête-flammes qui préviennent la transmission d'une flamme en présence de mélanges explosifs gaz-air ou vapeur-air. Elle établit des principes homogènes pour la classification, la construction de base et les informations pour l'utilisation, y compris le marquage des arrête-flammes, et spécifie des méthodes d'essai permettant de vérifier les exigences de sécurité et de déterminer des limites de sécurité d'utilisation.
La présente Norme internationale est valide pour des pressions comprises entre 80 kPa et 160 kPa et des températures comprises entre −20 °C et +150 °C.
NOTE 1 Pour les arrête-flammes avec des conditions de fonctionnement qui relèvent du domaine d'application, mais qui sont en dehors des conditions atmosphériques, voir 7.4.
NOTE 2 Lors de la conception et des essais des arrête-flammes destinés à fonctionner dans des conditions autres que celles spécifiées ci-dessus, la présente Norme internationale peut être utilisée comme guide. Toutefois, il est conseillé d'effectuer des essais supplémentaires se rapportant spécifiquement aux conditions d'utilisation prévues. Cela est particulièrement important lorsque des températures et des pressions élevées sont appliquées. Les mélanges d'essai pourraient avoir besoin d'être modifiés dans ces cas.
NOTE 3 Il existe une norme supplémentaire IMO MSC/Circ. 677 pour l'application maritime émise par l'Organisation maritime internationale (OMI).
ISO 16852:2016 n'est pas applicable aux cas suivants:
- appareils externes de mesurage et de commande liés à la sécurité qui peuvent être nécessaires pour maintenir les conditions de fonctionnement dans les limites de sécurité établies;
NOTE 4 Les équipements intégrés de mesurage et de commande, par exemple des capteurs intégrés de température et de flamme, de même que des pièces qui, par exemple, sont prévues pour fondre (clavette d'arrêt), brûler (abri contre les intempéries) ou se courber (bandes bimétalliques), relèvent du domaine d'application de la présente Norme internationale.
- arrête-flammes utilisés pour des mélanges explosifs de vapeurs et de gaz qui ont tendance à s'autodécomposer (par exemple l'acétylène) ou qui sont chimiquement instables;
- arrête-flammes utilisés pour le disulfure de carbone, du fait de ses propriétés spécifiques;
- arrête-flammes destinés à être utilisés pour des mélanges autres que des mélanges gaz-air ou vapeur-air (par exemple avec un rapport oxygène-azote plus élevé, avec du chlore en tant qu'oxydant, etc.);
- modes opératoires d'essai des arrête-flammes pour les moteurs à combustion interne et à allumage par compression;
- soupapes à action rapide, systèmes de coincement et autres systèmes d'isolement d'explosion.
Plamenske zapore - Zahtevane lastnosti, preskusne metode in omejitve uporabe (ISO 16852:2016)
Ta mednarodni standard določa zahteve za plamenske zapore, ki preprečujejo širjenje plamena v prisotnosti eksplozivnih mešanic plinov in zraka ali hlapov in zraka. Uveljavlja enotna načela za razvrstitev, osnovno konstrukcijo in informacije za uporabo, vključno z označevanjem plamenskih zapor, ter določa preskusne metode za preverjanje varnostnih zahtev in določanje varnih omejitev uporabe.
Ta mednarodni standard se uporablja za tlake med 80 kPa in 160 kPa ter temperature
med −20 °C in 150 °C.
OPOMBA 1: Za plamenske zapore s pogoji delovanja, ki so znotraj določenega obsega vendar zunaj atmosferskih pogojev, glej točko 7.4.
OPOMBA 2: Pri načrtovanju in preskušanju plamenskih zapor za delovanje v pogojih, ki se razlikujejo od zgoraj določenih, se lahko ta mednarodni standard uporabi kot vodilo, vendar se priporoča izvedba dodatnih preskusov za predvidene pogoje uporabe. To je pomembno zlasti, kadar je proizvod izpostavljen visokim temperaturam in tlaku. Preskusne mešanice je v teh primerih morda treba spremeniti.
OPOMBA 3: Obstaja dodatni standard IMO MSC/Circ. 677 za pomorsko uporabo, ki ga je sestavila Mednarodna pomorska organizacija (IMO).
Ta mednarodni standard se ne uporablja za:
– zunanjo varnostno merilno in nadzorno opremo, ki je morda potrebna za vzdrževanje
delovnih pogojev znotraj določenih varnih omejitev;
OPOMBA 4: Vgrajena merilna in nadzorna oprema, kot so vgrajeni senzorji temperature in plamena, ter deli, ki se na primer namensko topijo (zatiči), zgorijo (zaščita pred vremenskimi vplivi) ali se upogibajo
(dvokovinski trakovi), spadajo na področje uporabe tega mednarodnega standarda.
– plamenske zapore, ki se uporabljajo za eksplozivne mešanice samorazgradljivih
(npr. acetilen) ali kemično nestabilnih hlapov in plinov;
– plamenske zapore, ki se uporabljajo za ogljikov disulfid, zaradi njegovih posebnih lastnosti;
– plamenske zapore, ki se uporabljajo za mešanice, ki niso mešanice plinov in zraka ali hlapov in zraka (npr.
mešanice z višjim razmerjem kisika proti dušiku, mešanice s klorom kot oksidantom itd.);
– preskusne postopke za plamenske zapore za motorje z notranjim izgorevanjem in kompresijskim vžigom;
– hitro delujoče ventile, gasilne sisteme in druge sisteme za izolacijo eksplozij.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-februar-2017
1DGRPHãþD
SIST EN ISO 16852:2010
Plamenske zapore - Zahtevane lastnosti, preskusne metode in omejitve uporabe
(ISO 16852:2016)
Flame arresters - Performance requirements, test methods and limits for use (ISO
16852:2016)
Flammendurchschlagsicherungen - Leistungsanforderungen, Prüfverfahren und
Einsatzgrenzen (ISO 16852:2016)
Arrête-flammes - Exigences de performance, méthodes d'essai et limites d'utilisation
(ISO 16852:2016)
Ta slovenski standard je istoveten z: EN ISO 16852:2016
ICS:
13.220.10 Gašenje požara Fire-fighting
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 16852
EUROPEAN STANDARD
NORME EUROPÉENNE
November 2016
EUROPÄISCHE NORM
ICS 13.220.10 Supersedes EN ISO 16852:2010
English Version
Flame arresters - Performance requirements, test methods
and limits for use (ISO 16852:2016)
Arrête-flammes - Exigences de performance, méthodes Flammendurchschlagsicherungen -
d'essai et limites d'utilisation (ISO 16852:2016) Leistungsanforderungen, Prüfverfahren und
Einsatzgrenzen (ISO 16852:2016)
This European Standard was approved by CEN on 19 September 2016.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2016 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 16852:2016 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
Annex ZA (informative) Relationship between this European Standard and the Essential
Requirements of EU Directive 2014/34/EU concerning equipment and protective
systems intended for use in potentially explosive atmospheres . 4
European foreword
This document (EN ISO 16852:2016) has been prepared by Technical Committee ISO/TC 21
“Equipment for fire protection and fire fighting” in collaboration with Technical Committee CEN/TC 305
“Potentially explosive atmospheres — Explosion prevention and protection” the secretariat of which is
held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by May 2017, and conflicting national standards shall be
withdrawn at the latest by May 2017.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent
rights.
This document supersedes EN ISO 16852:2010.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this
document.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 16852:2016 has been approved by CEN as EN ISO 16852:2016 without any modification.
Annex ZA
(informative)
Relationship between this European Standard and the Essential
Requirements of EU Directive 2014/34/EU concerning equipment and
protective systems intended for use in potentially explosive atmospheres
This European Standard has been prepared under a mandate given to CEN by the European
Commission and the European Free Trade Association to provide a means of conforming to Essential
Requirements of the New Approach Directive 2014/34/EU concerning equipment and protective
systems intended for use in potentially explosive atmospheres
Once this standard is cited in the Official Journal of the European Union under that Directive and has
been implemented as a national standard in at least one Member State, compliance with the clauses of
this standard given in Table ZA.1 confers, within the limits of the scope of this standard, a presumption
of conformity with the corresponding Essential Requirements of that Directive and associated EFTA
regulations.
Table ZA.1 — Correspondence between this European Standard and Directive 2014/34/EU
concerning equipment and protective systems intended for use in potentially explosive
atmospheres
Essential Requirements (ERs) of Clause(s)/subclause(s) of this EN
Qualifying remarks/Notes
Directive 2014/34/EU
1.0.1 Principles of integrated Clause 5; 6.2
explosion safety
1.0.2 Design and manufacture 6.2; 7.1
considerations
1.0.3 Special checking and Annex C
maintenance conditions
1.0.4 Surrounding area conditions 6.2
1.0.5 Marking 12.2
1.0.6 Instructions 7.4; 8.4; 9.3; 10.3; 12.1
1.1.1 Operational stresses on 6.2; 7.1; Annex C
material
1.1.2 Reaction of material 6.2; Annex C
1.1.3 Wear of material 6.2; 7.1
1.2.1 Design and construction for 5.1; 6.2; 6.3; 6.4; 6.5; 7.1;
safe operation
1.2.3 Enclosed structures and 6.6
prevention of leaks
1.2.5 Additional mans of protection 12.1
1.2.8 Overloading of equipment 7.3.4; 10.1; 11.1
1.2.9 Flameproof enclosure systems 6.3; 6.4; 7.3.2.3
1.3.1 Hazards arising from different 6.2
ignition sources
1.3.2 Hazards arising from static Annex B; Annex C
electricity
1.4.1 External effects 6.2
1.4.2 Mechanical, thermal and 6.2
chemical stresses
1.6.4 Hazards arising from 6.4
connections
3.0.1 Dimensioning 6; 7; 8; 9; 10; 11
3.0.2 Design and position 6; 7; 8; 9; 10; 11
3.1.2 Shock waves 6.5; 7.3.3
WARNING — Other requirements and other EU Directives may be applicable to the product(s) falling
within the scope of this standard.
INTERNATIONAL ISO
STANDARD 16852
Second edition
2016-10-15
Flame arresters — Performance
requirements, test methods and
limits for use
Arrête-flammes — Exigences de performance, méthodes d’essai et
limites d’utilisation
Reference number
ISO 16852:2016(E)
©
ISO 2016
ISO 16852:2016(E)
© ISO 2016, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2016 – All rights reserved
ISO 16852:2016(E)
Contents Page
Foreword .v
Introduction .vii
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Abbreviated terms and symbols . 5
5 Hazards and flame arrester classifications . 6
5.1 Flame transmission: deflagration, stable and unstable detonation . 6
5.2 Flame transmission: stabilized burning . 7
6 General requirements . 7
6.1 Measuring instruments . 7
6.2 Construction . 7
6.3 Housings . 7
6.4 Joints . 8
6.5 Pressure test . 8
6.6 Leak test . 8
6.7 Flow measurement (air) . 8
6.8 Flame transmission test . 8
6.8.1 General. 8
6.8.2 Test mixtures . 9
6.9 Summary of tests to be conducted .10
7 Specific requirements for static flame arresters .11
7.1 Construction .11
7.2 Design series .11
7.3 Flame transmission test .12
7.3.1 General.12
7.3.2 Deflagration test .12
7.3.3 Detonation test .16
7.3.4 Short time burning test .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.