SIST EN ISO 374-5:2017

Protective gloves against dangerous chemicals and micro-organisms - Part 5: Terminology and performance requirements for micro-organisms risks (ISO 374-5:2016)

This European Standard specifies a test method for the penetration resistance of gloves that protect against
micro-organisms.
NOTE If other protection features should be needed, e.g. chemical risks, mechanical risks , thermal risks ,
electrostatic dissipation etc., the appropriate specific performance standard, e.g. EN 374-1, EN 388, EN 407,
EN 16350 etc., should be used.

Schutzhandschuhe gegen gefährliche Chemikalien und Mikroorganismen - Teil 5: Terminologie und Leistungsanforderungen für Risiken durch Mikroorganismen (ISO 374-5:2016)

Dieser Teil von ISO 374 legt ein Prüfverfahren für den Widerstand gegen Penetration von Handschuhen fest, die vor Mikroorganismen schützen.
ANMERKUNG   Wenn weitere Schutzmerkmale, z. B. chemische Risiken, mechanische Risiken, thermische Risiken, elektrostatische Entladung, erforderlich sind, muss zusätzlich die entsprechende spezifische Leistungsnorm verwendet werden. Weitere Informationen zu Schutzhandschuh-Normen können in EN 420 gefunden werden.

Gants de protection contre les micro-organismes - Partie 5: Terminologie et exigences de performance pour des risques par des micro-organisme (ISO 374-5:2016)

L'ISO 374-5:2016 spécifie une méthode d'essai permettant de déterminer la résistance à la pénétration des gants qui protègent contre les micro-organismes.
NOTE       Si d'autres fonctions de protection doivent être couvertes, par exemple les risques mécaniques, les risques thermiques, la dissipation électrostatique, etc., il convient que la norme de performance spécifique appropriée soit utilisée en complément. Des informations supplémentaires sur les normes concernant les gants de protection peuvent se trouver dans l'EN 420.

Varovalne rokavice za zaščito pred nevarnimi kemikalijami in mikroorganizmi - 5. del: Izrazje in zahtevane lastnosti za zaščito pred tveganji, povezanimi z mikroorganizmi (ISO 374-5:2016)

Ta evropski standard določa preskusno metodo za rokavice, odporne proti predrtju, ki ščitijo pred mikroorganizmi. OPOMBA: Če je treba zajeti tudi druge zaščitne lastnosti, npr. kemične nevarnosti, mehanske nevarnosti, toplotne nevarnosti, elektrostatično razelektritev itd., je treba uporabiti tudi ustrezne standarde zmogljivosti, npr. EN 374-1, EN 388, EN 407, EN 16350 idr.

General Information

• Status: Published
• Public Enquiry End Date: 19-Jul-2015
• Publication Date: 31-Jan-2017
• ICS: 13.340.40 - Hand and arm protection
• Technical Committee: OVP - Personal protecting equipment
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 03-Jan-2017
• Due Date: 10-Mar-2017
• Completion Date: 01-Feb-2017
• Directive: 2016/425 - Regulation (EU) 2016/425 of the European Parliament and of the Council of 9 March 2016 on personal protective equipment and repealing Council Directive 89/686/EEC
• Directive: 89/686/EEC - Council Directive 89/686/EEC of 21 December 1989 on the approximation of the laws of the Member States relating to personal protective equipment
• Mandate: M/031 - Standardization mandate to CEN/CENELEC concerning standards for Personal Protective Equipment
• Ref Project: EN ISO 374-5:2016 - Protective gloves against dangerous chemicals and micro-organisms - Part 5: Terminology and performance requirements for micro-organisms risks (ISO 374-5:2016)

Relations

• Revises: oSIST prEN ISO 374-5:2022 - Protective gloves against dangerous chemicals and micro-organisms - Part 5: Terminology and performance requirements for micro-organisms risks (ISO/DIS 374-5:2022)
• Effective Date: 18-Jan-2023
• Revises: oSIST prEN ISO 374-5:2022 - Protective gloves against dangerous chemicals and micro-organisms - Part 5: Terminology and performance requirements for micro-organisms risks (ISO/DIS 374-5:2022)
• Effective Date: 19-Jan-2023
• Revised: oSIST prEN ISO 374-5:2022 - Protective gloves against dangerous chemicals and micro-organisms - Part 5: Terminology and performance requirements for micro-organisms risks (ISO/DIS 374-5:2022)
• Effective Date: 23-Jun-2021

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 374-5:2017
01-marec-2017
9DURYDOQHURNDYLFH]D]DãþLWRSUHGQHYDUQLPLNHPLNDOLMDPLLQPLNURRUJDQL]PL
GHO,]UD]MHLQ]DKWHYDQHODVWQRVWL]D]DãþLWRSUHGWYHJDQMLSRYH]DQLPL]
PLNURRUJDQL]PL,62
Protective gloves against dangerous chemicals and micro-organisms - Part 5:
Terminology and performance requirements for micro-organisms risks (ISO 374-5:2016)
Schutzhandschuhe gegen gefährliche Chemikalien und Mikroorganismen - Teil 5:
Terminologie und Leistungsanforderungen für Risiken durch Mikroorganismen (ISO 374-
5:2016)
Gants de protection contre les micro-organismes - Partie 5: Terminologie et exigences
de performance pour des risques par des micro-organisme (ISO 374-5:2016)
Ta slovenski standard je istoveten z: EN ISO 374-5:2016
ICS:
13.340.40 Varovanje dlani in rok Hand and arm protection
SIST EN ISO 374-5:2017 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 374-5:2017

---------------------- Page: 2 ----------------------

SIST EN ISO 374-5:2017


EN ISO 374-5
EUROPEAN STANDARD

NORME EUROPÉENNE

November 2016
EUROPÄISCHE NORM
ICS 01.040.13; 13.340.40
English Version

Protective gloves against dangerous chemicals and micro-
organisms - Part 5: Terminology and performance
requirements for micro-organisms risks (ISO 374-5:2016)
Gants de protection contre les micro-organismes - Schutzhandschuhe gegen Chemikalien und
Partie 5: Terminologie et exigences de performance Mikroorganismen - Teil 5: Terminologie und
pour des risques par des micro-organisme (ISO 374- Leistungsanforderungen für Risiken durch
5:2016) Mikroorganismen (ISO 374-5:2016)
This European Standard was approved by CEN on 24 September 2016.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2016 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 374-5:2016 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 374-5:2017
EN ISO 374-5:2016 (E)
Contents Page
Europen foreword . 3
Annex ZA (informative) Relationship between this European Standard and the Essential
Requirements of EU Directive 89/686/EEC . 4

2

---------------------- Page: 4 ----------------------

SIST EN ISO 374-5:2017
EN ISO 374-5:2016 (E)
Europen foreword
This document (EN ISO 374-5:2016) has been prepared by Technical Committee CEN/TC 162
“Protective clothing including hand and arm protection and lifejackets", the secretariat of which is held
by DIN, in collaboration with Technical Committee ISO/TC 94 "Personal safety - Protective clothing and
equipment".
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by May 2017, and conflicting national standards shall be
withdrawn at the latest by May 2017.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent
rights.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this
document.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia,
Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands,
Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 374-5:2016 has been approved by CEN as EN ISO 374-5:2016 without any modification.
3

---------------------- Page: 5 ----------------------

SIST EN ISO 374-5:2017
EN ISO 374-5:2016 (E)
Annex ZA
(informative)
Relationship between this European Standard and the Essential
Requirements of EU Directive 89/686/EEC
This European Standard has been prepared under a mandate given to CEN by the European
Commission and the European Free Trade Association to provide a means of conforming to Essential
Requirements of the New Approach Directive 89/686/EEC on the approximation of the laws of the
Member States relating to personal protective equipment.
Once this standard is cited in the Official Journal of the European Union under that Directive and has
been implemented as a national standard in at least one Member State, compliance with the clauses of
this standard given in Table ZA confers, within the limits of the scope of this standard, a presumption of
conformity with the corresponding Essential Requirements of that Directive and associated EFTA
regulations
Table ZA — Correspondence between this European Standard and Directive (Add the reference
and title of the Directive)
Essential Requirements (ERs) of Directive 89/686/EEC Clause(s)/ Qualifying
subclause(s remarks/
) of this EN Notes
1.4 Information supplied by the manufacturer Clause 7
PPE bearing one or more identification or recognition Clause 6
marks
2.12.
directly or indirectly relating to health and safety
Protection against dangerous substances and infective 5.2, 5.3 5.4
3.10
agents

3.10.2
Protection against cutaneous and ocular contact

WARNING — Other requirements and other EU Directives may be applicable to the product(s) falling
within the scope of this standard.
4

---------------------- Page: 6 ----------------------

SIST EN ISO 374-5:2017
INTERNATIONAL ISO
STANDARD 374-5
First edition
2016-10-15
Protective gloves against dangerous
chemicals and micro-organisms —
Part 5:
Terminology and performance
requirements for micro-organisms
risks
Gants de protection contre les micro-organismes —
Partie 5: Terminologie et exigences de performance pour des risques
par des micro-organisme
Reference number
ISO 374-5:2016(E)
©
ISO 2016

---------------------- Page: 7 ----------------------

SIST EN ISO 374-5:2017
ISO 374-5:2016(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2016, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. [phone]
Fax [phone]
[e-mail]
www.iso.org
ii © ISO 2016 – All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 374-5:2017
ISO 374-5:2016(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Sampling . 2
4.1 Sampling for viral penetration testing . 2
4.2 Sampling for bacteria/fungi penetration testing . 2
5 Performance requirement . 3
5.1 General requirements .
...