SIST EN 14895:2006
(Main)Bitumen and bituminous binders - Stabilisation of binder from bituminous emulsions or from cut-back and fluxed bituminous binders
Bitumen and bituminous binders - Stabilisation of binder from bituminous emulsions or from cut-back and fluxed bituminous binders
This document specifies a method for the stabilisation of binder from bituminous emulsions or from cut-back or fluxed bituminous binders that will permit further testing.
It applies to all types of bituminous emulsion, with or without polymers, and as well as to all types of bituminous cut-back and fluxed materials, with or without polymers.
WARNING — The use of this document may involve hazardous materials, operations and equipment. This document does not purport to address all of the safety problems associated with its use. The hazards associated with the use of this method have been assessed using cut-back bitumen containing 10 % kerosene and 90 % 160/220 penetration grade bitumen and were found to be acceptable. However it is the responsibility of the user of this document to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Bitumen und bitumenhaltige Bindemittel - Stabilisierung von Bindemittel aus Bitumenemulsionen oder verschnittenen oder gefluxten bitumenhaltigen Bindemitteln
Dieses Dokument legt ein Verfahren fest, mit dem das Bindemittel aus Bitumenemulsionen oder
verschnittenen oder gefluxten bitumenhaltigen Bindemitteln so stabilisiert werden kann, dass eine weitere
Prüfung möglich wird.
Es gilt für alle Arten von Bitumenemulsionen, mit oder ohne Polymer(en), sowie für alle Arten von
bitumenhaltigen verschnittenen und gefluxten Materialien, mit oder ohne Polymer(en).
WARNUNG : Die Anwendung dieses Dokuments kann den Umgang mit gefährlichen Substanzen und
Ausrüstungen sowie die Durchführung gefährlicher Arbeitsschritte einschließen. Dieses Dokument
erhebt nicht den Anspruch, dass alle mit seiner Anwendung verbundenen Sicherheitsprobleme
angesprochen werden. Die mit der Anwendung dieses Verfahrens verbundene Gefährdung wurde mit
verschnittenem Bitumen mit 10 % Kerosin und mit 90 % Bitumen der Penetration 160/220 ermittelt und
war niedrig genug, um als akzeptabel angesehen zu werden. Jedoch liegt es in der Verantwortung des
Anwenders dieses Dokuments, geeignete Vorsichtsmaßnahmen für den Arbeits- und
Gesundheitsschutz zu treffen und die Anwendbarkeit einschränkender Vorschriften vor der
Anwendung zu bestimmen.
Bitumes et liants bitumineux - Stabilisation du liant d'une émulsion de bitume ou d'un bitume fluxé ou fluidifié
Le présent document prescrit une méthode pour la stabilisation du liant d'émulsions bitumineuses ou de liants
bitumineux fluidifiés ou fluxés, pour permettre la réalisation d'essais ultérieurs.
Elle s'applique a tous les types d'émulsions bitumineuses, avec ou sans polymeres, ainsi qu'a tous les types
de produits bitumineux fluidifiés et fluxés, avec ou sans polymeres.
AVERTISSEMENT : La mise en oeuvre du présent document peut impliquer l'utilisation de produits,
des manipulations et des appareillages a caractere dangereux. Le présent document n'est pas censé
aborder tous les problemes de sécurité concernés par son usage. Les risques découlant de la mise en
oeuvre de cette méthode ont été évalués en l'appliquant a un bitume fluidifié contenant 10 % de
kérosene et 90 % de bitume de classe de pénétrabilité 160/220, il a été établi que ces risques étaient
suffisamment faibles pour etre acceptables. Cependant, il est de la responsabilité de l'utilisateur du
présent document d'établir des regles de sécurité et d'hygiene appropriées et de déterminer
l'applicabilité des restrictions réglementaires avant son utilisation.
Bitumen in bitumenska veziva – Stabilizacija veziva iz bitumenskih emulzij ali rezanih in fluksiranih bitumnov
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Bitumen and bituminous binders - Stabilisation of binder from bituminous emulsions or from cut-back and fluxed bituminous bindersBitumen in bitumenska veziva – Stabilizacija veziva iz bitumenskih emulzij ali rezanih in fluksiranih bitumnovBitumes et liants bitumineux - Stabilisation du liant d'une émulsion de bitume ou d'un bitume fluxé ou fluidifiéBitumen und bitumenhaltige Bindemittel - Stabilisierung von Bindemittel aus Bitumenemulsionen oder verschnittenen oder gefluxten bitumenhaltigen BindemittelnTa slovenski standard je istoveten z:EN 14895:2006SIST EN 14895:2006en91.100.5075.140ICS:SLOVENSKI
STANDARDSIST EN 14895:200601-september-2006
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 14895April 2006ICS 75.140; 91.100.50 English VersionBitumen and bituminous binders - Stabilisation of binder frombituminous emulsions or from cut-back and fluxed bituminousbindersBitumes et liants bitumineux - Stabilisation du liant d'uneémulsion de bitume ou d'un bitume fluxé ou fluidifiéBitumen und bitumenhaltige Bindemittel - Stabilisierung vonBindemittel aus Bitumenemulsionen oder verschnittenenoder gefluxten bitumenhaltigen BindemittelnThis European Standard was approved by CEN on 27 February 2006.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2006 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 14895:2006: E
EN 14895:2006 (E) 2 Contents Page Foreword.3 1 Scope.4 2 Normative references.4 3 Terms and definitions.4 4 Principle.4 5 Apparatus.5 6 Sampling.5 7 Procedure.5 8 Test report.7 Bibliography.8
EN 14895:2006 (E) 3 Foreword This document (EN 14895:2006) has been prepared by Technical Committee CEN/TC 336 “Bituminous binders”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2006, and conflicting national standards shall be withdrawn at the latest by October 2006. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EN 14895:2006 (E) 4 1 Scope This document specifies a method for the stabilisation of binder from bituminous emulsions or from cut-back or fluxed bituminous binders that will permit further testing. It applies to all types of bituminous emulsion, with or without polymers, and as well as to all types of bituminous cut-back and fluxed materials, with or without polymers. WARNING — The use of this document may involve hazardous materials, operations and equipment. This document does not purport to address all of the safety problems associated with its use. The hazards associated with the use of this method have been assessed using cut-back bitumen containing 10 % kerosene and 90 % 160/220 penetration grade bitumen and were found to be low enough to be acceptable. However it is the responsibility of the user of this document to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 58, Bitumen and bituminous binders – Sampling bituminous binders EN 12594, Bitumen and bituminous binders – Preparation of test samples EN 13074, Bitumen and bituminous binders – Recovery of binder from bitumen emulsions by evaporation 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 recovered binder material remaining after the treatment of a bituminous emulsion under the condition specified in 7.1.1 or cut-back or fluxed bituminous binders under the conditions specified in 7.2.1 of this document 3.2 stabilised binder binder free from most of the volatile part of its flux oils obtained from recovered binder (defined in 3.1) by treatment at 85 °C for 24 h under the conditions specified in 7.1.2 or 7.2.2
4 Principle 4.1 Bituminous emulsion A thin layer of bituminous emulsion is spread onto a sheet of suitable non-stick material and is allowed to stand in the laboratory for 24 h at ambient temperature and in a ventilated oven at 50 °C for 24 h according to EN 13074. This recovered binder is then stabilised for 24 h at 85 °C in a ventilated oven.
EN 14895:2006 (E) 5 4.2 Cut-back or fluxed bituminous materials A thin layer of cut-back or fluxed bituminous b
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.