Bitumen and bituminous binders - Preparation of test samples

This European Standard specifies a method for preparing samples of bituminous binders in order to test their properties.
WARNING - Use of this European Standard can involve hazardous materials, operations and equipment. This European Standard does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this European Standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Bitumen und bitumenhaltige Bindemittel - Vorbereitung von Untersuchungsproben

Diese Europäische Norm legt ein Verfahren zur Vorbereitung von Proben von Bitumen und bitumenhaltigen Bindemitteln zur Prüfung ihrer Eigenschaften fest.
WARNUNG — Die Anwendung dieser Europäischen Norm kann den Umgang mit gefährlichen Substanzen und Ausrüstungsteilen und die Ausführung gefährlicher Arbeitsgänge einschließen. Diese Europäische Norm erhebt nicht den Anspruch, alle mit ihrer Anwendung verbundenen Sicherheitsprobleme anzusprechen. Es liegt in der Verantwortung des Anwenders dieser Europäischen Norm, geeignete Verhaltensregeln zur Sicherheit und Gesundheit festzulegen und die Anwendbarkeit einschränkender Vorschriften vor der Anwendung zu bestimmen.

Bitumes et liants bitumineux - Préparation des échantillons d'essai

La présente Norme européenne prescrit une méthode de préparation des échantillons de liants bitumineux afin de tester leurs propriétés.
AVERTISSEMENT — L'utilisation de la présente Norme européenne peut nécessiter des produits, des opérations et des équipements dangereux. La présente norme européenne n’est pas censée aborder tous les problèmes de sécurité concernés par son utilisation. Il est de la responsabilité de l'utilisateur de la présente Norme européenne de consulter et d'établir des règles de sécurité et d'hygiène appropriées et de déterminer si des restrictions réglementaires sont applicables avant son utilisation.

Bitumen in bitumenska veziva - Priprava preskusnih vzorcev

Ta evropski standard določa metodo priprave preskusnih vzorcev bitumenskih veziv za preskus njihovih lastnosti.
OPOZORILO – pri uporabi tega evropskega standarda so lahko prisotni nevarni materiali, postopki in oprema. Ta evropski standard ne obravnava vseh varnostnih težav, ki se nanašajo na njegovo uporabo. Za vzpostavitev ustreznih varnostnih in zdravstvenih praks ter za določitev uporabnosti regulativnih omejitev pred uporabo je odgovoren uporabnik tega evropskega standarda.

General Information

Status
Published
Public Enquiry End Date
19-May-2013
Publication Date
24-Nov-2014
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
10-Nov-2014
Due Date
15-Jan-2015
Completion Date
25-Nov-2014

RELATIONS

Buy Standard

Standard
SIST EN 12594:2014
English language
10 pages
sale 10% off
Preview
sale 10% off
Preview

e-Library read for
1 day

Standards Content (sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Bitumen in bitumenska veziva - Priprava preskusnih vzorcevBitumen und bitumenhaltige Bindemittel - Vorbereitung von UntersuchungsprobenBitumes et liants bitumineux - Préparation des échantillons d'essaiBitumen and bituminous binders - Preparation of test samples91.100.50Veziva. Tesnilni materialiBinders. Sealing materials75.140Voski, bitumni in drugi naftni proizvodiWaxes, bituminous materials and other petroleum productsICS:Ta slovenski standard je istoveten z:EN 12594:2014SIST EN 12594:2014en,fr,de01-december-2014SIST EN 12594:2014SLOVENSKI

STANDARDSIST EN 12594:20071DGRPHãþD
SIST EN 12594:2014
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 12594
November 2014 ICS 75.140; 91.100.50 Supersedes EN 12594:2007English Version
Bitumen and bituminous binders - Preparation of test samples
Bitumes et liants bitumineux - Préparation des échantillons d'essai

Bitumen und bitumenhaltige Bindemittel - Vorbereitung von Untersuchungsproben This European Standard was approved by CEN on 16 August 2014.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,

B-1000 Brussels © 2014 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12594:2014 ESIST EN 12594:2014

EN 12594:2014 (E) 2 Contents Page Foreword ..............................................................................................................................................................3 1 Scope ......................................................................................................................................................4 2 Normative references ............................................................................................................................4 3 Terms and definitions ...........................................................................................................................5 4 Principle ..................................................................................................................................................5 5 Reagents and materials ........................................................................................................................5 6 Apparatus ...............................................................................................................................................6 7 Procedure for sample preparation .......................................................................................................6 8 Test report ..............................................................................................................................................9

SIST EN 12594:2014

EN 12594:2014 (E) 3 Foreword This document (EN 12594:2014) has been prepared by Technical Committee CEN/TC 336 “Bituminous binders”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2015 and conflicting national standards shall be withdrawn at the latest by May 2015. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 12594:2007. In comparison with EN 12594:2007, the following significant changes have been made: — changed/added wording of the Warning in the Scope; — normative reference to ISO 5280 Xylene for industrial use – specification has been deleted; — subclause 5.3: reference to xylene deleted; — references to hot jacket oven (subclause 6.2) and hot air bath (subclause 7.2) have been deleted;

— changed wording of first paragraph of subclause 7.1.2; — subclause 7.1.2: time unit added for sample size 2 l to 3 l containers; — subclause 7.2: maximum temperature for cutbacks has been changed to 60 °C; — subclause 7.4 has been rephrased. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. SIST EN 12594:2014

EN 12594:2014 (E) 4 1 Scope This European Standard specifies a method for preparing samples of bituminous binders in order to test their properties. WARNING — Use of this European Standard can involve hazardous materials, operations and equipment. This European Standard does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this European Standard to identify the hazards and assess the risks involved in performing this test method and to implement sufficient control measures to protect individual operators (and the environment). This includes appropriate safety and health practices and determination of the applicability of regulatory limitations prior to use. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 58:2012, Bitumen and bituminous binders — Sampling bituminous binders EN 1425, Bitumen and bituminous binders — Characterization of perceptible properties EN 1427, Bitumen and bituminous binders — Determination of the softening point — Ring and Ball method EN 1429, Bitumen and bituminous binders — Determination of residue on sieving of bituminous emulsions, and determination of storage stability by sieving EN 1431, Bitumen and bituminous binders — Determination of residual binder and oil distillate from bitumen emulsions by distillation EN 12607-1, Bitumen and bituminous binders — Determination of the resistance to hardening under the influence of heat and air — Part 1: RTFOT method EN 12607-2, Bitumen and bituminous binders — Determination of the resistance to hardening under the influence of heat and air — Part 2: TFOT Method EN 12607-3, Bitumen and bituminous binders — Determination of the resistance to hardening under the influence of heat and air — Part 3: RFT Method EN 12697-1, Bituminous mixtures — Test methods for hot mix asphalt — Part 1: Soluble binder content EN 12697-2, Bituminous mixtures — Test method for hot mix asphalt — Part 2: Determination of particle size distribution EN 12697-4, Bituminous mixtures — Test methods for hot mix asphalt — Part 4: Bitumen recovery: Fractionating column EN 12847, Bitumen and bituminous binders — Determination of settling tendency of bituminous emulsions EN 13074-1, Bitumen and bituminous binders — Recovery of binder from bituminous emulsion or cut-back or fluxed bituminous binders — Part 1: Recovery by evaporation EN 13074-2, Bitumen and bituminous binders — Recovery of binder from bituminous emulsion or cut-back or fluxed bituminous binders — Part 2: Stabilisation after recovery by evaporation SIST EN 12594:2014

EN 12594:2014 (E) 5 EN 14023, Bitumen and bituminous binders — Specification framework for polymer modified bitumens EN 14769, Bitumen and bituminous binders — Accelerated long-term ageing conditioning by a Pressure Ageing Vessel (PAV) EN ISO 3696:1995, Water for analytical laboratory use — Specification and test methods (ISO 3696:1987) 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 58:2012 and the following apply. 3.1 laboratory sample sample of bituminous binder intended for laboratory tests Note 1 to entry: It may be a spot sample, a composite sample or a part thereof (a divided sample). 3.2 test sample sample of bituminous binder produced by treatment or subdivision of a laboratory sample for individual testing 4 Principle In order to produce the laboratory sample, the test material shall have been sampled in accordance with EN 58. Perceptible properties of the test material shall be checked in accordance with EN 1425, prior to performing this European Standard. Homogenize the laboratory sample before the test samples are taken. For certain tests (7.3.2), transfer the laboratory sample directly to the test sample containers, and for other tests (7.3.3), sieve the laboratory sample prior to testing. Store the laboratory sample from which the test samples are taken under controlled conditions. Stir gently to render it uniform and warm the sample, if necessary. Prepare all test samples that are required for one property at the same time. 5 Reagents and materials Use only reagents of standard analytical grade and water conforming to grade 3 of EN ISO 3696:1995. 5.1 Solution Sa Aqueous solution with a nominal 0,01 mol/l of sodium hydroxide (NaOH) containing a nominal 1 % mass fraction sodium oleate. This solution may be used for preparing anionic emulsion samples. The actual soap solution may be used if available on site, in case of routine tests or for simplicity. NOTE Sa stands for “anionic solution” as this solution is used for preparing anionic emulsion samples. SIST EN 12594:2014

EN 12594:2014 (E) 6 5.2 Solution Sc Aqueous solution of nominal 0,01 mol/l of hydrochloric acid (HCl) containing a nominal 1 % mass fraction cetyltrimethylammonium bromide. This solution may be used fo

...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.