oSIST prEN IEC 60794-1-107:2024
(Main)Optical fibre cables - Part 1-107: Generic specification - Basic optical cable test procedures - Mechanical test methods - Torsion, Method E7
Optical fibre cables - Part 1-107: Generic specification - Basic optical cable test procedures - Mechanical test methods - Torsion, Method E7
Câbles à fibres optiques - Partie 1-107: Spécification générique - Procédures fondamentales d’essais des câbles optiques - Méthodes d’essais mécaniques - Torsion, méthode e7
Optični kabli - 1-107. del: Splošna specifikacija - Osnovni preskusni postopki za optične kable - Mehanske preskusne metode - Torzija, metoda E7
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
01-september-2024
Optični kabli - 1-107. del: Splošna specifikacija - Osnovni preskusni postopki za
optične kable - Mehanske preskusne metode - Torzija, metoda E7
Optical fibre cables - Part 1-107: Generic specification - Basic optical cable test
procedures - Mechanical test methods - Torsion, Method E7
Câbles à fibres optiques - Partie 1-107: Spécification générique - Procédures
fondamentales d’essais des câbles optiques - Méthodes d’essais mécaniques - Torsion,
méthode e7
Ta slovenski standard je istoveten z: prEN IEC 60794-1-107:2024
ICS:
19.060 Mehansko preskušanje Mechanical testing
33.180.10 (Optična) vlakna in kabli Fibres and cables
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
86A/2464/CDV
COMMITTEE DRAFT FOR VOTE (CDV)
PROJECT NUMBER:
IEC 60794-1-107 ED1
DATE OF CIRCULATION: CLOSING DATE FOR VOTING:
2024-06-21 2024-09-13
SUPERSEDES DOCUMENTS:
86A/2417/CD, 86A/2461/CC
IEC SC 86A : FIBRES AND CABLES
SECRETARIAT: SECRETARY:
France Mr Laurent Gasca
OF INTEREST TO THE FOLLOWING COMMITTEES: PROPOSED HORIZONTAL STANDARD:
Other TC/SCs are requested to indicate their interest, if any, in
this CDV to the secretary.
FUNCTIONS CONCERNED:
EMC ENVIRONMENT QUALITY ASSURANCE SAFETY
SUBMITTED FOR CENELEC PARALLEL VOTING NOT SUBMITTED FOR CENELEC PARALLEL VOTING
Attention IEC-CENELEC parallel voting
The attention of IEC National Committees, members of CENELEC,
is drawn to the fact that this Committee Draft for Vote (CDV) is
submitted for parallel voting.
The CENELEC members are invited to vote through the CENELEC
online voting system.
This document is still under study and subject to change. It should not be used for reference purposes.
Recipients of this document are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Recipients of this document are invited to submit, with their comments, notification of any relevant “In Some Countries” clau ses to be
included should this proposal proceed. Recipients are reminded that the CDV stage is the final stage for submitting ISC c lauses.
(SEE AC/22/2007 OR NEW GUIDANCE DOC).
TITLE:
Optical fibre cables - Part 1-107: Generic specification - Basic optical cable test procedures - Mechanical test
methods - Torsion, Method E7
PROPOSED STABILITY DATE: 2028
NOTE FROM TC/SC OFFICERS:
file, to make a copy and to print out the content for the sole purpose of preparing National Committee positions. You may not copy
or "mirror" the file or printed version of the document, or any part of it, for any other purpose without permission in writi ng from IEC.
86A/2464/CDV - 2 - IEC CDV 60794-1-107 © IEC 2024
CONTENTS
FOREWORD . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Method E7 – Torsion . 5
4.1 Object . 5
4.2 Sample . 6
4.3 Apparatus . 6
4.4 Procedure . 7
4.5 Requirements . 8
4.6 Details to be specified . 8
4.7 Details to be reported . 9
Bibliography . 10
Figure 1 – Cable torsion apparatus . 6
Figure 2 – Cable torsion apparatus with tension applied . 6
Figure 3 – Alternative cable torsion apparatus with tension applied . 7
Table 1 – Typical test length . 7
IEC CDV 60794-1-107 © IEC 2024 - 3 - 86A/2464/CDV
1 INTERNATIONAL ELECTROTECHNICAL COMMISSION
2 ____________
4 OPTICAL FIBRE CABLES –
6 Part 1-107: Generic specification –
7 Basic optical cable test procedures –
8 Mechanical test methods – Torsion, Method E7
10 FOREWORD
11 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
12 all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
13 co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
14 in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
15 Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their
16 preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
17 may participate in this preparatory work. International, governmental and non-governmental organizations liaising
18 with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
19 Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
20 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
21 consensus of opinion on the relevant subjects since each technical committee has representation from all
22 interested IEC National Committees.
23 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
24 Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
25 Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
26 misinterpretation by any end user.
27 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
28 transparently to the maximum extent possible in their national and regional publications. Any divergence between
29 any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
30 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
31 assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
32 services carried out by independent certification bodies.
33 6) All users should ensure that they have the latest edition of this publication.
34 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
35 members of its technical committees and IEC National Committees for any personal injury, property damage or
36 other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
37 expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
38 Publications.
39 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
40 indispensable for the correct application of this publication.
41 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent
42 rights. IEC shall not be held responsible for identifying any or all such patent rights.
43 IEC 60794-1-107 has been prepared by subcommittee 86A: Fibres and cables, of IEC technical
44 committee 86: Fibre optics. It is an International Standard.
45 This document partially replaces IEC 60794-1-21:2015+AMD1:2020 CSV.
46 This edition includes the following significant technical changes with respect to IEC 60794 -1-
47 21:2015+AMD1:2020 CSV:
48 a) this document cancels and replaces method E7 of IEC 60794-1-21:2015+AMD1:2020
49 CSV;
50 b) update the typical test length according to different types of cables;
51 c) update Figure 2 by loading weights to cable gripping fixture.
52 The text of this an International Standard is based on the following documents:
86A/2464/CDV - 4 - IEC CDV 60794-1-107 © IEC 2024
Draft Report on voting
XX/XX/FDIS XX/XX/RVD
54 Full information on the voting for its approval can be found in the report on voting indicated in
55 the above table.
56 The language used for the development of this an International Standard is English.
57 This document was drafted in accordance with ISO/IEC Directives, Part 2, and developed in
58 accordance with ISO/IEC Directives, Part 1 and ISO/IEC Directives, IEC Supplement, available
59 at www.iec.
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.